Service bulletins for the 2021 Ford Mustang Mach-E
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
329 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Driver assistance are shown. Show all
| 26B07 | 2026-10-02. Other. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; UNKNOWN OR OTHER; ELECTRICAL SYSTEM. Recommended Repair Prior to Sale Customer Satisfaction Program 26B07 Certain 2021-2025 Model Year F-150 Lightning and Mustang Mach-E Vehicles Undesired Acceleration Due to Adaptive Cruise Control (ACC) Activation |
|---|---|
| TSB 26-2199 | 2026-05-05. Service bulletin. BACK OVER PREVENTION: WARNINGS; ELECTRICAL SYSTEM; UNKNOWN OR OTHER; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: WARNINGS. This article supersedes TSB 26-2021. Reason for update: to clarify prior approval requirements in the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to the coaxial cable between the IPMA camera and the IPMA. |
| SSM 54720 | 2026-04-10. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Various 2020-2026 Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern. |
| SSM 54668 | 2026-04-06. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION; LANE DEPARTURE: WARNING; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: WARNINGS; LANE DEPARTURE: ASSIST. Some 2021-2023 Mach-E and 2022-2024 F-150 vehicles may have customers or dealerships that wish to activate new BlueCruise features (example: Lane Change Assist). New BlueCruise features can only be activated/delivered via an over-the-air update (OTA). Inform customers that they will need to wait for the update to be pushed to their vehicle. There is no way to manually push the update. If the update fails, OTA will re-attempt an update later. |
| TSB 26-2021 | 2026-02-04. Service bulletin. ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; UNKNOWN OR OTHER. This article supersedes TSB 25-2156 to update the Service Procedure and Labor Time Allowance. Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to a connection issue between the IPMA Camera and the IPMA. |
| SSM 54313 | 2025-10-28. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION; ELECTRICAL SYSTEM. Some 2020-2025 various Ford and Lincoln vehicles equipped with blind spot information system (BLIS) may experience an inoperative blind spot monitoring with a "Blind Spot System Fault" message displayed in the instrument panel cluster (IPC). This may also be accompanied by diagnostic trouble codes (DTCs) B118C:11 and/or B118C:15 stored in the driver door module (DDM), and/or B118D:11 and/or B118D:15 stored in the passenger door module (PDM). This may be due to the wiring connector from the mirror to the BLIS module. If diagnostics lead to an internal mirror wiring harness fault, a new lower level BLIS light pigtail is now released for service. It is not necessary to replace the exterior mirror assembly. Use part number SC3Z-14A411-B to resolve the concern. |
| TSB 25-2512 | 2025-10-28. Service bulletin. LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; ELECTRICAL SYSTEM. This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR. |
| TSB 25-2427 | 2025-09-18. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; LANE DEPARTURE: ASSIST. Some of the vehicles listed in the Model statement above may exhibit an inoperative Blue Cruise and Lane Keeping system with diagnostic trouble code (DTC) U3000:49 with a status byte of 8F stored in the camera module-rear (CMR). This may be due to the CMR software level. NOTE: The driver status monitor camera module may also be called camera module-rear. |
| SCCM-25.DC MachE | 2025-07-02. Over-the-air update. LANE DEPARTURE: WARNING; ELECTRICAL SYSTEM; LANE DEPARTURE: ASSIST. Quality improvements include: -Ensures the lane change assist turn signal flashes until the change maneuver is complete |
| 25-BC-CS-25.02.01 Mach E | 2025-06-03. Over-the-air update. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. "Quality improvements include: -Module configuration settings update to ensure BlueCruise functionality" |
| TSB 24-2251 | 2024-09-02. Service bulletin. LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS). |
| 21G01 S4 | 2024-06-06. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. Certain 2021 Model Year F-150 and Mustang Mach-E Vehicles with Ford Co-Pilot360™ Active 2.0 Prep Package (Includes Ford BlueCruise Prep Kit) - BlueCruise Module Programming |
| TSB 24-2027 | 2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. This article supersedes TSB 23-2399 to update the vehicle lines affected. 2021-2023 Mustang Mach-E and 2023 e-Transit vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to the software in the SOBDM. To correct this condition, follow the Service Procedure to reprogram the powertrain control module (PCM). |
| TSB 24-2012 | 2024-02-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. Some 2021-2023 Mach-E vehicles may exhibit the drive mode default to normal mode while driving and Drive Mode Not Available message displays in the center display screen with or without diagnostic trouble code (DTC) U0253 stored in the anti-lock brake system module (ABS). This may be due to the software in the SYNC module (APIM). The APIM software update that addresses the symptom listed in this bulletin may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply. |
| OTA SU7 P1 MachE | 2024-01-04. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM:ADAS:AUTONOMOUS/SELF DRIVING:SOFTWARE. Software Update SU7 P1 for 2021- 2023 MY Mach E vehicles is now available. Quality improvements include: - Reduces erroneous BLIS warning 21 MY: - Increases availability of BlueCruise. Ignition reset will not be necessary to reengage BlueCriuse. - Reduces false eyes-off warnings - Improved OTA success rate 21-22 MY: - Improved Reverse Brake assist availability - Customer is instructed to exit the vehicle when a battery hazard is detected - Enables the e-release feature on the front trunk. |
| SSM 52134 | 2023-12-19. Service bulletin. BACK OVER PREVENTION. Various 2021-2024 Ford and Lincoln vehicles equipped with the rear camera on demand feature may exhibit a Please Check Surroundings For Safety or Full View Not Available message when the rear camera button is pressed and the vehicle is not in reverse. Inform customers this condition is considered normal operation and does not affect vehicle durability because the full rear view camera image can only be shown when the vehicle is in reverse. No additional diagnosis or service is required for this condition. |
| SU6 P1 MACH E | 2023-10-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE. "Software Update SU6 P1 for 2021 - 2023 Mach E is now available. Quality improvements include: -Improved ""Ask on Exit"" pop- up functionality '- Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing. - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved Profiles (Enhanced Memory) - prevent getting stuck in GUEST. - Improved feedback of vehicle charging behavior when plugging-in. |
| PU0722-DC-CHG3 | 2023-09-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. "Priority Update 23- PU0722-DC-CHG3 for 2021- 2022 MACH E vehicles is now available. Quality Improvements include: -Robustness actions to improve DC fast charging performance/success rate" |
| SU5 P2 MACH E | 2023-09-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 5 P2 for 2021- 2022 MACH E vehicles is now available. Quality improvements include: - Improved motion sensor on/off selection pop- up when exiting. - Selectable Drive Modes communication robustness action to prevent unintended return to default drive mode. - Improved charge status indication feedback while plugged in. - Add in-vehicle message on infotainment screen to inform customer that some display features may be unavailable while SYNC is rebooting during SYNC OTA update installation. |
| SSM 51778 | 2023-07-20. Service bulletin. EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS; BACK OVER PREVENTION:SOFTWARE. Some 2020-2021 Escape built on/before 23-Nov-2021, 2021 F-150 built on/before 08-Oct-2021, 2021 Mustang Mach-E built on/before 29-Mar-2021, 2021 Expedition built on/before 05-Aug-2021, 2021 Explorer built on/before 27-Sep-2021 and 2020-2022 Edge may exhibit a concern of the audio system does not power on, no sound from audio speakers, chimes default to coming through the instrument cluster, no communication with audio control module (ACM) or digital signal processor (DSP) module, and/or diagnostic trouble code (DTC) U0184, U0237 and/or U0238. To correct the condition, perform a hard reset of the DSP by disconnecting the 12-volt battery. Reprogram the DSP module using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18B849 and any applicable labor operations in Section 10 of the Service Labor Time Standards Manual. |
| SSM 51776 | 2023-07-12. Service bulletin. EQUIPMENT; BACK OVER PREVENTION: CAMERA SYSTEM. Some 2021-2023 Mustang Mach-E/F-150, 2022-2023 Expedition/Navigator and 2023 Corsair vehicles may exhibit a Driver Monitoring Camera Blocked message and/or DTCs B115E:97, B15E1:97 and/or B15E2:97 stored in the driver status monitor camera module (CMR). These DTCs should be disregarded unless it is a DTC with a status byte 8F. Other status bytes should be disregarded as they may be caused by a camera obstruction such as driver position, aftermarket devices or dust on the camera. To clear the DTCs, remove anything obstructing the view of the camera and light emitting diodes (LEDs), place the steering wheel in the center position and close the driver door. Connect Ford Diagnosis and Repair System (FDRS) and clear the DTCs. Turn the ignition off and wait 10 seconds. Turn the ignition on and wait 1 minute. Perform the CMR self-test and reevaluate if DTCs persist. |
| 23PU0415BLMFXVIS | 2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Priority Update 23-PU0415-BLM-FX-VIS for 2021 - 2023 Mach E vehicles is now available Quality Improvements include: -Phone as a Key Passive Entry improvement |
| 23PU0407BCDCFXME | 2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Priority Update 23-PU0407-BCDC-FX for 2021 Mach E vehicles is now available: Quality Improvements include: -Restores driver assist functionality on specific VINs that may have a configuration mismatch with the server |
| 23OTASU4P2MACHE | 2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 4 P2 for 2021- 2023 Model Year Mach E vehicles is now available. Quality improvements include: Remove Reverse Brake Assist unavailable warning Remove Beltminder Tollbooth Mode Remove incorrect frunk service now pop- up. Improves hood ajar warnings/ chimes. New thermal parameters added for increased powertrain component protection. Ford Pass Charge settings - will not revert back to previous settings. |
| 23B28 | 2023-06-06. Service bulletin. BACK OVER PREVENTION. Certain 2021 Model Year Mustang Mach E Gateway Module Reprogramming In all the affected vehicles, the Gateway Module (GWM) may have lost internet connection after an OTA update. This may cause the vehicle to display a No Driver Logged message on the screen |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.