WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

644 on file from NHTSA, as of 2026-10-19.

About U3000 on the 2021 Ford F-150: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

Only bulletins with trouble code: U3000 are shown. Show all

Bulletins, newest first
TSB 26-23912026-09-12. Service bulletin. ELECTRICAL SYSTEM; UNKNOWN OR OTHER. This bulletin updates 26-2206. Reason for update: update the Service Procedure to revise Steps 19-21, adding Step 22, and adding Figure 15-16 to clarify connector C316 location. Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to the coaxial cable between the IPMA camera and the IPMA.
TSB 26-22062026-05-08. Service bulletin. FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; FORWARD COLLISION AVOIDANCE: WARNINGS; UNKNOWN OR OTHER; ELECTRICAL SYSTEM. This article updates TSB 23-2146. Reason for update: clarify prior approval requirements Some of the vehicles listed in the Model statement above may exhibit diagnostic trouble codes (DTCs) C1001:31, U3000:89, and/or U3000:49 stored in the image processing module A (IPMA) and at least one of the following conditions: "Front Camera Fault Service Required" message Pre-collision assist inoperative Adaptive cruise control inoperative Front windshield camera alignment routine fails to complete This may be due to the coaxial cable between the IPMA camera and the IPMA.
TSB 25-25122025-10-28. Service bulletin. LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL; ELECTRICAL SYSTEM. This article supersedes TSB 25-2104 to update the labor times associated with the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Inoperative BlueCruise and lane centering * DTC U2018:51 stored in the camera module - rear (CMR) * DTC U0565:86 stored in the image processing module A (IPMA) * DTC U3000:49 is not stored in the CMR This may be due to the software in the CMR.
TSB 25-24652025-10-09. Service bulletin. AIR BAGS. This article supersedes TSB 23-2280 to update labor times from M-time to fixed time. Some vehicles listed in the Model statement above, may exhibit an illuminated airbag warning indicator with diagnostic trouble codes (DTCs) U3000:41 and/or U3000:54 in the occupant classification system module (OCSM) and/or B00A0:09, B00A0:63, B00A0:64 and/or B00A0:68 in the restraints control module (RCM).
TSB 24-22512024-09-02. Service bulletin. LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS).
TSB 23-22802023-09-26. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 F-150 vehicles may exhibit an illuminated airbag indicator light that may be accompanied by diagnostic trouble codes (DTCs) U3000:41 and/or U3000:54 in the occupant classification system module (OCSM) and/or B00A0:09, B00A0:63, B00A0:64 and/or B00A0:68 in the restraints control module (RCM).
SSM 518942023-09-04. Service bulletin. ELECTRICAL SYSTEM; STEERING. Some 2021 F-150 vehicles may exhibit a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with DTC U3001:68 and/or U3001:89 along with U3000:96 in the power steering control module (PSCM). This may be due to low battery voltage when attempting to start the vehicle. Power steering assist will be restored when battery voltage is at or above 12 volts and the DTCs are cleared. Replacement of the PSCM is not necessary. Flash the PSCM to the latest software level and clear the DTCs afterwards. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal diagnostics. For claiming, use causal part 3504 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-21462023-05-16. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2021-2023 F-150 vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA) that will not clear and not be stored in the vehicle's history. DTC C1001:31 and/or U3000:89 may be stored in the IPMA, but may have recently been cleared and stored in the vehicle's history. This may be due to a connection issue between the IPMA Camera and the IPMA. To correct the condition, perform the following service procedure to repair the connection and reset the IPMA.
SSM 514342023-04-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2021-2022 F-150 vehicles equipped with On-Board Scale may exhibit DTC U3000:54 stored in the VDM after replacement and will not clear. This may be due to the configuration data for the VDM. To correct the condition, download and run the VDM - Vehicle Dynamics Module Configuration app using the latest level of the Ford Diagnosis and Repair System (FDRS). After the VDM configuration has completed, download and run the VDM - On Board Scales Calibration app and perform the Vehicle Payload Update and the Height Sensor Calibration to complete the repair. The Vehicle Payload Update entry in FDRS should correspond with the rating shown on the Tire and Load Information label found on either the B-pillar or the edge of the driver door. For claiming, use causal part 18B008 and applicable labor operations in Section 10 of the Service Labor Time Standards Manual.
TSB 23-20402023-03-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2021-2022 F-150 built on or before 19-May-2022, Mustang Mach-E built on or before 04-May-2022 and 2022 Expedition/Navigator vehicles built on or before 13-May-2022 may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
SSM 512262023-01-05. Service bulletin. UNKNOWN OR OTHER; STEERING:STEERING CONTROL MODULE; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2021-2023 F-150 vehicles may experience a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTC) U3001:89 and U3000:96 in the power steering control module (PSCM). This may be due to low voltage at the PSCM. Power steering assist will be restored when sufficient voltage is supplied. To clear the DTCs using the Ford Diagnosis and Repair System (FDRS), select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal diagnostics. For claiming, use causal part 3504.
SSM 509522022-07-29. Service bulletin. EQUIPMENT. Some 2021-2022 F-150 vehicles equipped with On-Board Scale may exhibit DTC U3000:54 stored in the VDM after replacement and will not clear. A warning message may also be displayed in the center display screen. If programmable module installation (PMI) was not followed or the original VDM will not communicate, the U3000:54 may be stored. If the original VDM communicates, perform a PMI before VDM removal. This DTC does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution that is expected in September 2022. Replacement or reprogramming of the VDM will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available
TSB 22-22952022-07-28. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2021-2022 F-150, Mustang Mach-E and 2022 Expedition/Navigator vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. DTC B1578:78 may also set after an image processing module A (IPMA) on-demand self test is performed. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
TSB 22-21092022-03-29. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. This article supersedes TSB 22-2069 to update the Service Procedure. Some 2021 F-150 and Mustang Mach-E vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. DTC B1578:78 may also set after an image processing module A (IPMA) on-demand self test is performed. This may be due to software in the IPMA. To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
TSB 22-20692022-03-08. Service bulletin. FORWARD COLLISION AVOIDANCE; LANE DEPARTURE. Some 2021 F-150 vehicles built on or before 22-Jul-2021 at Dearborn Truck Plant, 2021 F-150 vehicles built on or before 08-Oct-2021 at Kansas City Assembly Plant and Mustang Mach-E vehicles built on or before 07-Jul-2021 may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. This may be due to software in the image processing module A (IPMA). The revised IPMA calibration is currently not available.
SSM 504842022-02-16. Service bulletin. STEERING. Some 2021 F-150 vehicles built on or before 17-Mar-2021 may experience a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTC) U3000:96 and U3001:68 in the power steering control module (PSCM). This may be due to battery voltage below 8 volts when attempting to start the vehicle. Power steering assist will be restored when battery voltage is at or above 12 volts and the DTCs are cleared. Replacement of the PSCM is not necessary. To clear the DTCs using the FDRS, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal diagnostics. For claiming, use causal part 3504.
SSM 502022021-10-29. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:ABS WARNING LIGHT. Some 2021 F-150 vehicles may experience an illuminated anti-lock brake system (ABS) indicator in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) U3000:48 stored in the ABS module. The U3000:48 DTC in the ABS module typically sets in conjunction with various chassis DTCs. When addressing related ABS concerns, all chassis DTCs are to be diagnosed and resolved first using Workshop Manual (WSM), Section 206-09, before attempting to diagnose and resolve any network communication DTCs.
TSB 21-22492021-08-02. Service bulletin. ELECTRICAL SYSTEM. Some 2021 F-150 and Mustang Mach-E vehicles may exhibit various driver assistance system warning messages or inoperative features and/or diagnostic trouble codes (DTC) U3000:49, U3000:89, U2107:68, C1001:54 and/or C1001:78. This may be due to software in the image processing module A (IPMA). To correct the condition, follow the Service Procedure to reprogram the IPMA to the latest level.
SSM 496842021-03-31. Service bulletin. ELECTRICAL SYSTEM. Some 2021 F-150 vehicles may exhibit diagnostic trouble code (DTC) U3000:49 stored in the image processing module A (IPMA). This may be due to the learned values in the IPMA not allowing the code to be cleared. To clear the DTC, download and run the IPMA - Reset the Image Processing Module A (IPMA) Learned Values application in Ford Diagnosis and Repair System (FDRS), then run the IPMA - Image Processing Module A (IPMA) Alignment application immediately after. If the U3000:49 is still present after running both applications, continue with normal diagnostics in Pinpoint Test AI in Workshop Manual, Section 419-07.
SSM 495302021-03-03. Service bulletin. STEERING. Some 2021 F-150 vehicles may experience a lack of steering assist upon start-up along with a Steering Assist Fault message in the instrument panel cluster (IPC) with diagnostic trouble codes (DTC) U3000:96 and U3001:68 in the power steering control module (PSCM). This may be due to battery voltage below 8 volts when attempting to start the vehicle. Power steering assist will be restored when battery voltage is at or above 12 volts and the DTCs are cleared. Replacement of the PSCM is not necessary. To clear the DTCs using the FDRS, select and run the PSCM - Reset the Power Steering Control Module (PSCM) application. Once cleared, cycle the ignition to verify normal system operation. If the DTCs return, refer to Workshop Manual Section 211-02 for normal diagnostics. For claiming, use causal part 3504.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.