WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Ford Mustang Mach-E

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

329 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
SSM 519032023-10-04. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Ford and Lincoln vehicles may exhibit DTCs U2100 and/or U3002 stored in the cruise control module (CCM), side obstacle detection control module LH (SODL), side obstacle detection control module RH (SODR), side obstacle detection control module C (SODCMC) and/or side obstacle detection control module D (SODCMD) after a module replacement. DTC U2100 may set when the module has not been properly configured after replacement. DTC U3002 may set when the module has been configured with the incorrect VIN. To correct this condition, verify that the module storing the DTC has been installed following the applicable Workshop Manual (WSM) Removal and Installation procedure. If the DTC is still stored, download and run the Vehicle Identification Number (VIN) Write application found under Toolbox, Multi-Module tab in the Ford Diagnosis and Repair System (FDRS).
TSB 23-22812023-10-03. Service bulletin. ELECTRICAL SYSTEM. his article supersedes TSB 22-2446 to update the Service Procedure. Some 2021 Mustang Mach-E vehicles built on or before 07-Jul-2021 may experience Frunk System Fault Service Required message displayed in the IPC after performing body control module (BCM) update. This may be due to the software in the BCM. To correct the condition, follow the Service Procedure to reprogram the SYNC module (APIM), BCM and front trunk release module (FTRM). NOTE: The APIM software update that addresses the symptom listed in this article may have been delivered over-the-air (OTA) via Ford Power-Up software updates to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history.
SU6 P1 MACH E2023-10-03. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE. "Software Update SU6 P1 for 2021 - 2023 Mach E is now available. Quality improvements include: -Improved ""Ask on Exit"" pop- up functionality '- Adds a ""some display features may be temporarily unavailable"" message to the SYNC screen when a SYNC update is installing. - Selectable Drive Modes - prevent default to normal mode due to loss of communication with SYNC - Improved Profiles (Enhanced Memory) - prevent getting stuck in GUEST. - Improved feedback of vehicle charging behavior when plugging-in.
PU0722-DC-CHG32023-09-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. "Priority Update 23- PU0722-DC-CHG3 for 2021- 2022 MACH E vehicles is now available. Quality Improvements include: -Robustness actions to improve DC fast charging performance/success rate"
SU5 P2 MACH E2023-09-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 5 P2 for 2021- 2022 MACH E vehicles is now available. Quality improvements include: - Improved motion sensor on/off selection pop- up when exiting. - Selectable Drive Modes communication robustness action to prevent unintended return to default drive mode. - Improved charge status indication feedback while plugged in. - Add in-vehicle message on infotainment screen to inform customer that some display features may be unavailable while SYNC is rebooting during SYNC OTA update installation.
SSM 518382023-09-04. Service bulletin. ELECTRICAL SYSTEM. In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SSM 518802023-09-02. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an inability to clear diagnostic trouble codes (DTCs) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics.
SSM 518662023-09-02. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Mustang Mach-E vehicles may exhibit an exterior charge status indicator blinking red with diagnostic trouble code (DTC) P0E5F stored in the secondary on-board diagnostic control module A (SOBDM) and the high voltage battery cannot be charged using a 48-amp AC level 2 charger. The vehicle may also exhibit in the next key cycle a Service Soon message in the instrument panel cluster (IPC) and a FordPass warning message. This may be due to an excessive charge port temperature. The concern may not be present when using a 32-amp or lower AC level 2 charger. To correct this condition, remove and replace the charge port. Refer to Workshop Manual (WSM) Section, 414-03B. For claiming, use causal part 14A303 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 23-22612023-09-01. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This article supersedes TSB 23-2168 to update the vehicle line affected. Some 2021-2022 Mustang Mach-E (non-GT) vehicles equipped with all-wheel drive (AWD) may exhibit a whine noise from the front drive unit when driving steady at speeds between 30-40 mph (48-64 km/h) without diagnostic trouble codes (DTCs) present. This may be due to software parameters. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
TSB 23-22572023-09-01. Service bulletin. ELECTRICAL SYSTEM:PROPULSION SYSTEM:TRACTION BATTERY:MANAGEMENT SYSTEM/ENERGY CONTROL MODULE (BMS/BECM); ELECTRICAL SYSTEM. Some 2021-2022 Mustang Mach-E vehicles built on or before 17-Mar-2023 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F, and/or P0C78 stored in battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box (HVBJB). To correct the condition, follow the Service Procedure to replace the HVBJB and reprogram the BECM.
SAN-Vol1 I12023-08-16. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This article includes information on warranty, technical service tips and other service information.
SSM 517782023-07-20. Service bulletin. EQUIPMENT:APPLIANCE:TV/RADIO/SPEAKERS; BACK OVER PREVENTION:SOFTWARE. Some 2020-2021 Escape built on/before 23-Nov-2021, 2021 F-150 built on/before 08-Oct-2021, 2021 Mustang Mach-E built on/before 29-Mar-2021, 2021 Expedition built on/before 05-Aug-2021, 2021 Explorer built on/before 27-Sep-2021 and 2020-2022 Edge may exhibit a concern of the audio system does not power on, no sound from audio speakers, chimes default to coming through the instrument cluster, no communication with audio control module (ACM) or digital signal processor (DSP) module, and/or diagnostic trouble code (DTC) U0184, U0237 and/or U0238. To correct the condition, perform a hard reset of the DSP by disconnecting the 12-volt battery. Reprogram the DSP module using the latest version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 18B849 and any applicable labor operations in Section 10 of the Service Labor Time Standards Manual.
SSM 517832023-07-18. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Ford and Lincoln vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). To restore charging capability, disconnect the off-board charging station charge handle from the vehicle charge port and reconnect. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in August 2023. Replacement of the SOBDM will not resolve this condition. Monitor OASIS for additional information.
SSM 517762023-07-12. Service bulletin. EQUIPMENT; BACK OVER PREVENTION: CAMERA SYSTEM. Some 2021-2023 Mustang Mach-E/F-150, 2022-2023 Expedition/Navigator and 2023 Corsair vehicles may exhibit a Driver Monitoring Camera Blocked message and/or DTCs B115E:97, B15E1:97 and/or B15E2:97 stored in the driver status monitor camera module (CMR). These DTCs should be disregarded unless it is a DTC with a status byte 8F. Other status bytes should be disregarded as they may be caused by a camera obstruction such as driver position, aftermarket devices or dust on the camera. To clear the DTCs, remove anything obstructing the view of the camera and light emitting diodes (LEDs), place the steering wheel in the center position and close the driver door. Connect Ford Diagnosis and Repair System (FDRS) and clear the DTCs. Turn the ignition off and wait 10 seconds. Turn the ignition on and wait 1 minute. Perform the CMR self-test and reevaluate if DTCs persist.
23P082023-07-07. Service bulletin. ELECTRICAL SYSTEM. Certain 2021-2023 Model Year Mustang Mach-E Door Control Module Update Some of the affected vehicles may exhibit a false alarm activation and/or a warning message in the FordPass application when the doors are locked
22B48 S12023-07-07. Service bulletin. ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:ONBOARD (OBCM); ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:SOFTWARE. Certain 2021-2022 Model Year Mustang Mach-E and 2022 Model Year E-Transit Vehicles - Off-Board Charger Controller Module Programming Technical Information update
22B482023-07-07. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:SOFTWARE. Certain 2021-2022 Model Year Mustang Mach-E and 2022 Model Year E-Transit Vehicles - Off-Board Charger Controller Module Programming Some Mustang Mach-E, and E-Transit battery electric vehicles (BEV) may experience inability to charge at certain charging stations
SSM 517272023-06-21. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES; ELECTRICAL SYSTEM:SOFTWARE. Some 2021-2023 Mustang Mach-E vehicles built on or before 21-Apr-2023 may exhibit a false alarm activation and/or warning message in the FordPass application when the doors are locked. This may be due to the software in the door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). To correct the condition, download and run the door control module software update application for each module one at a time using the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 58219A65 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 517052023-06-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. Vehicle may also exhibit reduced powertrain performance and/or a Stop Safely Now message displayed in the instrument panel cluster (IPC) and/or High-Voltage Battery Warning message in the FordPass application. This may be due to the BECM software. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics. Some 2021-2023 Mustang Mach-E and 2022-2023 E-Transit vehicles may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P0ADA, P0ADE, P0AA1, and/or P0AA4 stored in the battery energy control module (BECM) after high voltage battery junction box (HVBJB) replacement. Vehicle may also exhibit reduced powertrain performance and/or a Stop Safely Now message displayed in the instrument panel cluster (IPC) and/or High-Voltage Battery Warning message in the FordPass application. This may be due to the BECM software. To correct the condition, download and run the BECM - Reset Diagnostic Trouble Code (DTC) Occurrence Counter application in Ford Diagnosis and Repair System (FDRS). If the concern persists, refer to Workshop Manual (WSM), Section 414-03A for normal diagnostics
TSB 23-21702023-06-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2021 Mustang Mach-E and F-150 vehicles may fail PMI for the IPMA using the Ford Diagnosis and Repair System (FDRS) with an error stating Procedure Unsuccesful - GetFlashActionPartNumbers Unable To Obtain Flash Action Part Numbers From Available Topology if the power steering control module (PSCM), cruise control module (CCM), camera module - rear (CMR) and/or instrument panel cluster (IPC) are not at their latest software level prior to attempting PMI. To correct this condition follow the Service Procedure to update each of the modules necessary to complete PMI for the IPMA.
SSM 516962023-06-13. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some 2021-2022 Mustang Mach-E vehicles built on or before 19-Aug-2022 may exhibit a condition of intermittent headlamp operation while the vehicle is off and have diagnostic trouble code (DTC) B1533 stored in the body control module (BCM). This may be due to the internal logic within the headlamp switch. To correct this condition, replace the headlamp switch (service base PN: 11654). Refer Workshop Manual, Section 417-01. For claiming, use casual part 11654 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 516892023-06-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2021 Mustang Mach-E (Non-GT) vehicles built on or before 22-Jul-2021 may exhibit a buzz noise from the instrument panel cluster (IPC) that changes with the brightness setting. This may be due to the internal hardware in the IPC. To correct the condition, replace the IPC. Refer to Workshop Manual, Section 413-01. For claiming, use causal part 10849 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
23PU0415BLMFXVIS2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Priority Update 23-PU0415-BLM-FX-VIS for 2021 - 2023 Mach E vehicles is now available Quality Improvements include: -Phone as a Key Passive Entry improvement
23PU0407BCDCFXME2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Priority Update 23-PU0407-BCDC-FX for 2021 Mach E vehicles is now available: Quality Improvements include: -Restores driver assist functionality on specific VINs that may have a configuration mismatch with the server
23OTASU4P2MACHE2023-06-06. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 4 P2 for 2021- 2023 Model Year Mach E vehicles is now available. Quality improvements include: Remove Reverse Brake Assist unavailable warning Remove Beltminder Tollbooth Mode Remove incorrect frunk service now pop- up. Improves hood ajar warnings/ chimes. New thermal parameters added for increased powertrain component protection. Ford Pass Charge settings - will not revert back to previous settings.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.