WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

176 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 468622017-12-14. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Some owners of 2013-2018 Escape vehicles may complain of the rear license plate viewed in the lower portion of the display screen when using the parking aid camera. This is due to the convex camera lens to provide as much viewing angle as possible. This is a normal vehicle characteristic and no repairs or adjustments should be attempted to correct this condition.
SSM 468612017-12-14. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. To recover the screen, perform any one of the following actions: touch the SYNC screen anywhere outside the vehicle image pop-up box, safely shift the vehicle into and out of reverse, or perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). If this does not resolve the concern, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 468602017-12-14. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure allowing time for the SYNC system to complete all tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 468482017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates. SYNC 3 software upgrade to support these apps is not a warrantable repair per the Warranty And Policy Manual, Section 3, Warranty Coverages SYNC.
SSM 468342017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 468252017-10-21. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2016-2017 Escape vehicles built on or before 01-Apr-2017 may exhibit a concern with the OAT reading inaccurate and/or the A/C inoperative. This may be due to water in connector C134(20 pin) in the left front fender apron. If a vehicle comes in with this condition, access connector C134 in the 14290 harness. Refer to Wiring Manual. Check connector C134 for corrosion and/or water contamination. If present, replace the pigtail harness (Refer to Pigtail Application Guide Under Repair Kits in the Wiring Manual) and add electrical grease (XG-12). For claiming, use causal part 14S411 and applicable labor operations in section 11 of the service labor time standards (SLTS) manual
SSM 468132017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor OASIS for updates.
SSM 467032017-08-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Some 2013-2017 Edge/MKX/Escape/MKC/Fusion/MKZ/Flex/MKT/Mondeo/Kuga/EcoSport AWD vehicles where diagnosis leads to a RDU clutch issue, a rear drive unit (RDU) service kit is available. Use the vehicle identification number (VIN) in the parts catalog to look for base part 4A232. If clutch assembly (base 4A232) is not listed in the catalog, this message does not apply. For vehicle repairs refer to updated Workshop Manual (WSM), Section 205-02 on ATC clutch repairs. Use causal part 4A232 or equivalent and applicable labor operations.
16B322017-08-01. Service bulletin. VEHICLE SPEED CONTROL. Certain 2015 Model Year Edge, 2015-2016 Model Year F-150, MKT, and Police Interceptor Sedan, and 2016 Model Year Escape, Explorer, Flex, Fusion, MKX, Mustang, Police Interceptor Utility, Taurus, and Transit Vehicles - Electronic Throttle Body Repair
SSM 461022017-08-01. Service bulletin. SEAT BELTS:FRONT:RETRACTOR; SEAT BELTS. Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 460732017-08-01. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due to the power saving features enabled while in transportation mode. It is beneficial to extended battery life to keep the vehicle in Transport Mode until the vehicle is prepped for sale. If the vehicle should exhibit a blank screen or other SYNC symptoms after it has been taken out of Transport mode, refer to Workshop Manual, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 460612017-08-01. Service bulletin. EQUIPMENT; SERVICE BRAKES, HYDRAULIC. Some 2016-2017 Escape vehicles equipped with a 1.6L/1.5L AWD or a 2.0L FWD/AWD may exhibit front brake squeal when applying the brakes. The noise most commonly occurs after the brakes have warmed up, however the noise may occur during other driving conditions. If the front brakes display a continuous squeal noise, install front lining kit CV6Z-2001-N. Reference Workshop Manual (WSM) Section 206-03, removal and installation instructions. Use causal part 2001 and refer to section 2 of the SLTS manual for applicable labor operations.
TSB 16-20372017-08-01. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2015-2016 Escape and 2016 Fusion vehicles equipped with a 2.0L GTDI engine may exhibit a rolling reverse to drive engagement shudder on acceleration. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
TSB 16-01252017-08-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2016 Fusion and Escape vehicles equipped with 2.5L engine may experience a delayed engagement/shudder during a drive to reverse shift. This condition occurs when the throttle is applied during reverse engagement. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 102.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
TSB 16-01172017-08-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION; ELECTRICAL SYSTEM:SOFTWARE. Some 2016 Escape vehicles equipped with a 2.0L GTDI engine may exhibit no transmission upshift after a downshift event with cruise control engaged. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
TSB 17-20682017-08-01. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION: CAMERA SYSTEM. Some 2016-2017 Edge, Escape, Expedition, Fiesta, Flex, MKC, MKT, MKX, Mustang, Navigator and Taurus or 2017 Explorer and Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 Å'C to 5 Å'C (23 Å'F to 41 Å'F). This maybe due to a temperature dependent issue within the APIM crystal oscillator circuitry. Follow the Service Procedure steps to correct the condition.
SSM 464952017-05-24. Service bulletin. SUSPENSION. SOME 2015-2017 ESCAPE AND MKC VEHICLES WITHOUT A VEHICLE DYNAMIC SUSPENSION SYSTEM AND BUILT ON 1-APR-2015 AND THROUGH 1-OCT-2016 MAY EXHIBIT A RATTLE AND/OR CLUNKING NOISE FROM THE REAR SUSPENSION WHILE DRIVING OVER BUMPS AND/OR MAKING TURNS AT LOW SPEEDS. SUSPECT REAR SHOCK ABSORBERS WILL COMPRESS 2-5 INCHES OF TRAVEL BEFORE SIGNIFICANT RESISTANCE IS OBSERVED. IF WORKSHOP MANUAL (WSM), SECTION 100-04 DIAGNOSTICS INDICATE A RATTLE AND/OR CLUNKING NOISE IS COMING FROM THE REAR SHOCK ABSORBER(S) THEN REFER TO WSM, SECTION 204-02 AND REPLACE THE REAR SHOCK ABSORBER(S)AS REQUIRED. FOR CLAIMING, USE CAUSAL PART 18125 AND APPLICABLE LABOR OPERATIONS IN SECTION 5 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 464862017-05-24. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. SOME 2016-2017 FORD OR LINCOLN VEHICLES EQUIPPED WITH SYNC 3 MAY EXHIBIT A BLANK SCREEN OR OTHER VARIOUS SYNC SYMPTOMS ONLY WHEN THE VEHICLE IS IN TRANSPORT MODE. THIS IS CONSIDERED NORMAL DUE TO THE POWER SAVING FEATURES ENABLED WHILE IN TRANSPORT MODE. IT IS BENEFICIAL FOR BATTERY LIFE TO KEEP THE VEHICLE IN TRANSPORT MODE UNTIL THE VEHICLE IS PREPPED FOR SALE. TO PREVENT A SYNC SYSTEM LOCKUP DURING TRANSPORT MODE DEACTIVATION, FOLLOW THE WORKSHOP MANUAL (WSM) PROCEDURE EXACTLY ALLOWING TIME FOR THE SYNC SYSTEM TO COMPLETE ITS TASKS SUCH AS FULLY BOOTING UP OR POWERING DOWN AND SHUTTING OFF BEFORE MOVING TO THE NEXT STEP OF THE PROCEDURE. IF THE VEHICLE EXHIBITS A BLANK SCREEN OR SYNC SYMPTOMS AFTER TRANSPORT MODE DEACTIVATION, REFER TO WSM, SECTION 415-00 FOR NORMAL DIAGNOSIS. THE SYNC VERSION CAN BE CONFIRMED VIA OASIS.
SSM 464382017-05-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. SOME 2016-2017 F150, EDGE, MKX, ESCAPE, FOCUS, MKC, FUSION, MKZ, TAURUS AND 2017 CONTINENTAL VEHICLES EQUIPPED WITH 2.0L, 2.7L OR 3.0L GASOLINE TURBOCHARGED DIRECT INJECTION(GTDI) ECOBOOST ENGINES MAY EXHIBIT MALFUNCTION INDICATOR LIGHT(MIL) ON WITH DIAGNOSTIC TROUBLE CODES(DTC) P1013, P1015 AND/OR P1016 STORED IN POWERTRAIN CONTROL MODULE(PCM). CHECK TURBOCHARGER WASTEGATE CONTROL HOSES FOR WATER/ICE RESTRICTIONS OR PINCHING AT ZIP-TIE ON ENGINE CAM COVER RETAINER(2.7L AND 3.0L ONLY). IF RESTRICTION IS FOUND ON CAM COVER RETAINER, CUT ZIP TIE AND CLEAR DTCS. IF WATER/ICE RESTRICTION IS FOUND, DRAIN HOSES, REASSEMBLE AND CLEAR DTCS. IF DTCS RETURN, REFER TO WORKSHOP MANUAL (WSM) OR POWERTRAIN CONTROL EMISSIONS DIAGNOSIS (PCED) MANUAL FOR NORMAL DIAGNOSTICS. ENGINEERING IS INVESTIGATING THE CONCERN, MONITOR OASIS FOR FURTHER UPDATES.
TSB 17-00342017-05-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. SOME 2013-2017 ESCAPE VEHICLES BUILT ON OR BEFORE 28-FEB-2017 MAY EXHIBIT A NOISE AND/OR VIBRATION FROM THE CLIMATE CONTROL BLOWER MOTOR WITH OR WITHOUT A LACK OF AIRFLOW FROM PANEL REGISTERS AND MAY ALSO HAVE AN ODOR. THIS CONCERN MAY BE DUE TO SMALL ANIMALS THAT CAN ENTER THE BLOWER MOTOR HOUSING AREA THROUGH THE AIR INLET DUCT AND CAUSE DAMAGE TO THE AIR INLET DUCT ASSEMBLY AND/OR BLOWER MOTOR ASSEMBLY. THE SMALL ANIMALS MAY DEPOSIT FOREIGN MATERIAL IN THE BLOWER MOTOR ASSEMBLY AND AIR INLET HOUSING THAT MAY CAUSE LACK OF AIRFLOW, NOISE AND/OR VIBRATION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB 17-00272017-05-12. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. SOME 2015-2017 ESCAPE VEHICLES EQUIPPED WITH EMTC AND BUILT ON OR BEFORE 8-APR-2016 MAY EXHIBIT INCORRECT AIR DISTRIBUTION FROM THE INSTRUMENT PANEL REGISTERS WHEN PANEL MODE IS SELECTED ON THE HEATER VENTILATION AIR CONDITIONING (HVAC) CONTROL PANEL. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 462102017-03-20. Service bulletin. STEERING. SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
SSM 461702017-03-20. Service bulletin. EQUIPMENT. 2013-2017 ESCAPE VEHICLES EQUIPPED WITH MOONROOF EXHIBIT A SMALL VENT OPENING POSITION OF 5 MM. THIS IS THE NORMAL VENT POSITION FOR OPTIMAL NVH/WINDNOISE QUALITIES. WHEN THE VENT IS CLOSED, THE MOONROOF WILL OPEN TO THE 10 MM POSITION THEN CLOSE. THE SLIDING GLASS ALSO OPENS TO THE 10 MM POSITION TO GIVE THE GLASS ENOUGH CLEARANCE BEFORE IT OPENS TO THE REARWARD POSITION. THIS IS THE NORMAL OPERATING CHARACTERISTIC. NO REPAIRS ARE REQUIRED.
SSM 463552017-03-17. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR. MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.