Service bulletin TSB 16-2037

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10109052
Published by NHTSA	2017-08-01
Manufacturer's number	TSB 16-2037
Manufacturer's date	2016-09-14
NHTSA component	ELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)

NHTSA's summary

Some 2015-2016 Escape and 2016 Fusion vehicles equipped with a 2.0L GTDI engine may exhibit a rolling reverse to drive engagement shudder on acceleration. Reprogram the powertrain control module (PCM) to the latest calibration using IDS release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine, Transmission and driveline, Automatic transmission, Software, Transmission control module

Vehicles listed
FORD ESCAPE	2015, 2016
FORD FUSION	2016

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
22V413000	2022-06-10. POWER TRAIN:SHIFT LINKAGE/CABLE/ROD; POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
22V254000	2022-04-14. POWER TRAIN:SHIFT LINKAGE/CABLE/ROD; POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
19V362000	2019-05-13. POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT
18V471000	2018-07-16. POWER TRAIN:AUTOMATIC TRANSMISSION:LEVER AND LINKAGE:FLOOR SHIFT

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 50375	2021-12-27. Service bulletin. Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
TSB 21-2269	2021-09-30. Service bulletin. Some 2014-2019 Fusion vehicles built on or before 10-Jun-2019 and 2017-2019 Escape vehicles built on or before 08-Apr-2019 equipped with a 1.5L EcoBoost engine may exhibit low coolant level, white exhaust smoke and/or runs rough condition with or without an illuminated malfunction indicator light (MIL) with only diagnostic trouble codes (DTCs) P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To resolve the condition, follow the Service Procedure to replace the short block and head gasket.
SSM 49821	2021-06-01. Service bulletin. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 20-2255	2020-09-02. Service bulletin. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 19-2100	2019-05-06. Service bulletin. Some 2013-2015 Escape vehicles equipped with a 1.6L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) and/or a transmission malfunction service now warning with only diagnostic trouble codes (DTCs) P0741 and/or P1744 stored in the powertrain control module (PCM). This may be due to internal damage to the torque converter. To resolve the condition, repair or replace the affected internal transmission components as directed by the Service Procedure.
SSM 47710	2019-03-04. Service bulletin. Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 47041	2018-06-11. Service bulletin. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 47211	2018-05-21. Service bulletin. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 46900	2018-01-29. Service bulletin. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 46891	2017-12-14. Service bulletin. Some 2016 Escape and Focus vehicles equipped with a front control display interface module (FCDIM) may exhibit the inability to store AM/FM presets and/or preset buttons work erratically. Engineering is currently investigating this concern. Until a new service procedure and/or parts are available use the pre-set buttons in the following manner. To store/program a new station for a pre-set location, press and hold desired button for 3 seconds. To select a previously programmed pre-set location, perform a quick press and release of the button. Refer to Workshop Manual (WSM) Section, 415-00 for normal diagnostics. Continue to monitor OASIS for updates.