WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Chrysler Pacifica

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

553 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Backup camera are shown. Show all

Bulletins, newest first
90044522024-01-08. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. CAMERA, Rear View Prior to replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
S14080003842024-01-02. Service bulletin. BACK OVER PREVENTION; LANE DEPARTURE. Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
90033572024-01-02. Service bulletin. BACK OVER PREVENTION. ADAPTER, Engine Oil Filter (Pentastar V6) For all 2014MY replace the Oil Filter Adapter (OFA). For any other MY (with mileage above 30,000) review and follow instructions from STAR Online S1809000007 REV. C available on Dealer Connect. Also, consider the following: 1) Remove OFA 2) Replace only the oil inlet O-ring and gaskets (seals kit in SOL above). 3) Re-install the OFA. For 2023MY and beyond use black O-ring. For 2022MY and prior use red O-ring. Note: When replacing OFA, it may be necessary to transfer the Oil Temp/Pressure Sensor from the old OFA to the new OFA.
90044522023-10-30. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. CAMERA, Rear View Prior to replacement, please contact FCA Redacted Content. If no response in 15 minutes, proceed with repair.
18020232023-04-17. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0335 - Crankshaft Position Sensor Circuit (NA Only). ? P0339 - Crankshaft Position Sensor Intermittent (NA Only). Major monitor (misfire) and other diagnostics are disabled on a pending DTCs P0335 and P0339.** Software enhancement: Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states. ? Corrections to allow the vehicle to clear the permanent fault codes. This bulletin involves reprogramming the PCM with the latest available software. NOTE: Four modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this PCM update: ? Electronic Brake Booster Module (EBBM). ? AntiLock Brake System Module (ABS). ? Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) or also known as a Power Inverter Module (PIM).
S1623000028 Rev.2023-02-13. Service bulletin. VEHICLE SPEED CONTROL; BACK OVER PREVENTION; POWER TRAIN; VISIBILITY; PARKING BRAKE. Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
S20080000952023-01-09. Service bulletin. BACK OVER PREVENTION:DISPLAY FUNCTION. Service Shifter Is Displayed In the EVIC
08053172022-10-31. Service bulletin. EQUIPMENT:ELECTRICAL; BACK OVER PREVENTION:DISPLAY FUNCTION. RA3 and RA4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. Customers may experience one or more of the following:Radio functions/touchscreen locks up (does not affect backup camera). Phone presets do not save. ?Navigation Failed? message is displayed. Navigation is inoperative or inaccurate. CD player will not play songs and/or locks up the radio. Clock will not automatically update to local time. Clock may be off by several hours. (RA3 only). Poor or no connection to cellular network. ?Charge Complete? notification is not received (RU PHEV only). Some Uconnect® App remote commands do not execute with the vehicle. Radio Apps are inoperative. Radio display screen is black or blank. Battery drain - due to radio staying on. Navigation failed message is displayed. Clock not automatically updating to local time. Improvements:Auto Play can now be configured. Media devices, Phone pairing and Bluetooth® usage improvements. Add the ability to drag and drop icons into the menu bar. Adds ?Do Not Disturb? text message feature. Fix for radio locks up/frozen. Fix for radio loses time. Enhanced Voice recognition (VR) performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Human Machine Interface (HMI) improvements. Satellite radio reception improvements.
90037902022-10-31. Service bulletin. BACK OVER PREVENTION. Valve Cover and Gasket, Left and Right Pertains to vehicles equipped with a 3.6L V6 V.V.T. Engine only: Oil leaking from the valve cover onto the O2 sensor causing faults codes P0140, P2096, P0137, P0157. Need to verify the leak source and cause (gasket pinched, out of position, rolled, or cut). Please call one of the individuals below before proceeding with the repair. Also, if possible take a picture and send it to the emails listed below. First: Scott Knaggs - Cell (313) 363-6937 scott.knaggs@facgroup.com Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com If no response in 15 minutes, proceed with repair.
05048043A2022-10-31. Service bulletin. BACK OVER PREVENTION. PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
18069172022-10-24. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DiagnosticTrouble Codes (DTCs) have been set:U1400-00 - Implausible TPS Signal Received P1D73 - AGS Performance -(Active Grill Shutter). P0171 - Fuel System 1/1 Lean. P0174 - Fuel System 2/1 Lean. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to atwo trip fault:P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. The technician may also find the following DTC stored in the Anti-lock Brake System (ABS) Module memory:The following Diagnostic Trouble Code (DTC) is caused by a calibration in the PCM that is in conflict with the ABS Module programming. Thenew software flash will correct this issue.C121C-00 - Torque Request Signal Denied. This software release also includes:Improvement at lower ambient temperatures for Engine Stop/Start (ESS) Starts. Improvements to vehicle drivability during a cam sensor and/or crank sensor malfunction. Transmission quick learn. Engine enhancements.
08076172022-10-24. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Flash: On Board Charge Module (OBCM) Diagnostic and System Improvements This bulletin involves reprogramming the OBCM with the latest available software. Customers may notice when plugged in the vehicle for charging, sometimes it will not properly charge. Upon further investigation, a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P0CF3-00 - Control Pilot Circuit Open. P0CF4-00 - Control Pilot Circuit Performance.
90037562022-10-24. Service bulletin. BACK OVER PREVENTION; AIR BAGS; STEERING; PARKING BRAKE; ELECTRICAL SYSTEM. Rain light sensor Rain sense wipers do not operate: 1. Visual Inspection--> Check if the sensor is visually OK. (all the pins are OK) Check that the Connector is NOT loose (Sensor must get a voltage from 9V to 16V) 2. Functional Checks Rain--> Steering column switch is in auto mode (sensor is active) it is necessary to splash water on the sensitive surface of the sensor to trigger wipes. check the same for different sensitivities When the rain sensitivity is increased (for example from level 0 to level 1), as an acknowledgement a single wipe is seen. (This is not a phantom wipe) and this single wipe is not seen when the rain sensitivity is decreased (from higher level to lower level) Light--> Steering column switch is in auto mode (sensor is active) block the light coming on the sensor from outside of the vehicle (use a opaque object), the head lamps should be activated 3. If the sensor seems functional, it is ideal to remove the silicon gel pad from the sensor, replace it with the new silicon gel pad instead of replacing the whole sensor. When servicing the LRSM please replace the silicon gel pad with a new silicon gel pad (PN 68224945AA) instead of replacing the whole sensor.
S20230000422022-10-17. Service bulletin. BACK OVER PREVENTION. Wind Noise From Upper Corners Of Sliding Doors
S22230000082022-10-17. Service bulletin. BACK OVER PREVENTION. Squeak Noise Opening Front Doors
S2014000001RevA2022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:PRESSURE SENSOR; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS/RECEPTACLES. (Revision A) When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit.
90038252022-09-15. Service bulletin. SEATS; VEHICLE SPEED CONTROL; ELECTRICAL SYSTEM; AIR BAGS; BACK OVER PREVENTION. LATCH, Hood For the following concerns, please verify secondary plunger switch before replacing hood latch with primary switch. Please refer to service information for complete diagnostics of the secondary plunger switch which is located in the left front under hood on RU, MP, and WK/WD and left rear under hood on KL. 1) Electronic Stop Start Message on Cluster or DTC P152F without hood ajar illuminated. 2) KL Hood ajar light is on or unlatched hood due to high closing effort. (KL hood may have a higher closing effort to latch the hood as rubber bumper interference is set purposely high to prevent hood flutter at highway speeds) If stop start message or DTC P152F is present on vehicles without a hood ajar light illuminated, the issue is not related to the primary hood latch switch.
08-049-172022-09-15. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION. Central Vision Processing Module (CVPM) Enhancements for Surround View Camera System This bulletin involves updating the CVPM with the latest available software. Customers may experience that in variable light conditions (i.e. backing into a garage on a sunny day), image harmonization between the four views can lead to part of the image being blacked outFig. 1.360 Surround View Camera
08-130-212022-08-22. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; ELECTRICAL SYSTEM:PROPULSION SYSTEM:HYBRID MANAGEMENT. Flash: Battery Pack Control Module (BPCM) Diagnostic and System Updates This bulletin involves updating the BPCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may one or more of the following Diagnostic Trouble Codes (DTCs) have been set: P0AA1-00 - Hybrid/EV Battery Positive Contactor ?A? Stuck Closed. P0AA4-00 - Hybrid Battery Negative Contactor Circuit Stuck Closed. P0C78-00 - Hybrid/EV Battery System Precharge Time Too Long. P0B3C-00 - Hybrid/EV Battery Voltage Sense 1 Circuit Performance. P0B41-00 - Hybrid/EV Battery Voltage Sense 2 Circuit Performance. P0B46-00 - Hybrid/EV Battery Voltage Sense 3 Circuit Performance. P0B4B-00 - Hybrid/EV Battery Voltage Sense 4 Circuit Performance. P0B50-00 - Hybrid/EV Battery Voltage Sense 5 Circuit Performance. P0B55-00 - Hybrid/EV Battery Voltage Sense 6 Circuit Performance. P1A16-00 - Hybrid/EV Wakeup Control 3 Output Circuit/Open. P1D7B-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Battery. P1D7C-00 - Hybrid/EV Wakeup Control 3 Output Circuit Short to Ground. P1A29 - Cell Supervisory Circuit A Failure. P1A2A - Cell Supervisory Circuit B Failure. P1D3E - Internal Control Module Shut Off Test Error. U0594 - Implausible Data Received from HCP. P2BE5 - Hybrid/EV Battery Pack Current Sensor "C" Circuit Performance. B12B0-85 - Charge Temperature Indicator-Signal Above Allowable Range. Customer may also experience one or more of the following: Premature oil change message displayed on the cluster and vehicle may be running in fuel/oil refresh mode. Scheduled charging not functioning properly because the battery pack did not wake up while plugged in.
23-032-162022-08-22. Service bulletin. BACK OVER PREVENTION; VEHICLE SPEED CONTROL. Sliding Door Lubrication. This bulletin involves applying NYE lubricant grease to the sliding door center track mechanism. Customers may describe a grinding noise coming from the left or right sliding door when opening or closing.
90035842022-08-08. Service bulletin. BACK OVER PREVENTION; STEERING; POWER TRAIN. Electric Power Steering Gear If any of the following DTCs exist, it is okay to replace the steering gear: C2217-00, C15C1-00 (EPS Mechanical Performance) or C15DB-00 (Latch Active) otherwise perform the following; 1) Electrical, Communication or DTC (other then above) issue please contact: Terry Gavit @ cell (248) 882-6108 terry.gavit@fcagroup.com Engineering is requesting a copy of Vehicle Scan Report (VSR) to be emailed to the above address. 2) Noise or Mechanical issue please contact: Ruth Delong @ cell (810) 569-0354.~ If you do not receive a return call within 15 minutes, proceed with the repair.~ Please be sure to attach a copy of the Vehicle Scan Report on the repair order
23-047-172022-08-08. Service bulletin. SEATS; SEAT BELTS:REAR/OTHER:RETRACTOR; ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:PROPULSION SYSTEM: CABLES:FASTENER/CONNECTOR; BACK OVER PREVENTION. Seat Pops or Clicks After Seatback Is Adjusted This bulletin involves adjusting the recliner cable on the second row quad seats. The customer may describe after adjusting one or both of the inboard seat upper seatbacks, a pop or clicking noise can be heard.
08-007-212022-07-18. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION; POWER TRAIN; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment:Vehicle will not start when it is cold (-30°C-22°F and below). Heard and/or felt bump when the gas engine turns on while driving This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP&AHCP update:Powertrain Control Module (PCM) Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS).
08-044-17A2021-05-03. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Combination reprogramming of the HCP and the AHCP with the latest available software.
08-007-212021-02-16. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; EXTERIOR LIGHTING; POWER TRAIN; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment:Vehicle will not start when it is cold (-30°C-22°F and below). Heard and/or felt bump when the gas engine turns on while driving This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP&AHCP update:Powertrain Control Module (PCM) Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.