WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Chrysler Pacifica

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

553 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Fuel system are shown. Show all

Bulletins, newest first
90045092023-01-09. Service bulletin. FUEL SYSTEM, OTHER:FUEL FILTER. Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2208000020RevA2022-10-31. Service bulletin. FUEL SYSTEM, GASOLINE. Electric Mode Temporarily Unavailable, Cluster Message Displayed Vehicle in Fuel Oil Refresh Mode (FORM)
90038042022-10-31. Service bulletin. VEHICLE SPEED CONTROL; FUEL SYSTEM, GASOLINE. Fuel Tank Before replacing this part due to Hard to Fill condition, check the Fuel Filler Tube for restriction after the second door of the capless unit. Replace the Fuel Filler Tube if the second door of the capless unit does not open properly or if there is restriction after the second door of the capless unit. Contact Sylvia Lopez at cell (248) 520-9734 if a tank needs to be replaced.
18069172022-10-24. Service bulletin. BACK OVER PREVENTION; EXTERIOR LIGHTING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: Powertrain Diagnostic and System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with thelatest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DiagnosticTrouble Codes (DTCs) have been set:U1400-00 - Implausible TPS Signal Received P1D73 - AGS Performance -(Active Grill Shutter). P0171 - Fuel System 1/1 Lean. P0174 - Fuel System 2/1 Lean. The following Diagnostic Trouble Codes (DTCs) have been changed from a one trip fault to atwo trip fault:P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. The technician may also find the following DTC stored in the Anti-lock Brake System (ABS) Module memory:The following Diagnostic Trouble Code (DTC) is caused by a calibration in the PCM that is in conflict with the ABS Module programming. Thenew software flash will correct this issue.C121C-00 - Torque Request Signal Denied. This software release also includes:Improvement at lower ambient temperatures for Engine Stop/Start (ESS) Starts. Improvements to vehicle drivability during a cam sensor and/or crank sensor malfunction. Transmission quick learn. Engine enhancements.
90045092022-10-17. Service bulletin. FUEL SYSTEM, OTHER:FUEL FILTER. Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
S2014000001RevA2022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:PRESSURE SENSOR; FUEL SYSTEM, GASOLINE; BACK OVER PREVENTION; ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS/RECEPTACLES. (Revision A) When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit.
S20140000012022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:PRESSURE SENSOR; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS/RECEPTACLES. When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit. Improper wiring of the replacement connector can result in DTC P018D-Fuel Pressure Sensor High setting in the PCM.
90042832022-09-26. Service bulletin. FUEL SYSTEM, GASOLINE. TUBE, Fuel Supply If replacing Fuel Supply Tube PN 68421782A$ please refer to STAR Online publication S2014000001 for updated pressure sensor connector pin out information.
90045092022-09-26. Service bulletin. FUEL SYSTEM, OTHER:FUEL FILTER. Oil Filter If a Mopar Oil Filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. Recommended Brands: Wix, Purolator, and NapaGold
90037302022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; WHEELS. SI-eVT Transmission - China Variant & 9 inertia ring bolts For SI-eVT Transmission ONLY: Replace the nine (9) flywheel to damper bolts (68382486AA) when replacing the SI-eVT per TechConnect procedure. SI-eVTs built prior to January 11, 2019 had a 05192374AB level cooler. Using service SI-evT built after Jan 11 2019 with the 05192374AC level cooler requires new 68238385AB inlet hose and 68238386AC outlet hose. The service SI-eVT is shipped with a non-China wiring harness (68241331AC). China market replacement must replace wiring harness with 68368596AA. The China variant 68368596AA wiring harness has an interlock to the electrical charge door.
23-026-16 REV. A2022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE. Incorrect Front License Plate Bracket This bulletin involves inspecting and if necessary, replacing the front license plate bracket. The vehicle may have the incorrect front license plate bracket in the vehicle. The vehicle may have a been shipped with a license plate bracket kit for a high line fascia that will not fit vehicles with a base line fascia.
90036942022-08-08. Service bulletin. FUEL SYSTEM, GASOLINE. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
08-007-212022-07-18. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM; BACK OVER PREVENTION; POWER TRAIN; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment:Vehicle will not start when it is cold (-30°C-22°F and below). Heard and/or felt bump when the gas engine turns on while driving This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP&AHCP update:Powertrain Control Module (PCM) Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS).
08-007-212021-02-16. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; EXTERIOR LIGHTING; POWER TRAIN; BACK OVER PREVENTION; ENGINE AND ENGINE COOLING. Flash: Hybrid Control Processor (HCP) and Auxiliary Hybrid Control Processor (AHCP) Updates This bulletin involves reprogramming the HCP and AHCP or also known as Power Inverter Module (PIM) with the latest available software. Technicians and/or customers may report the vehicle will not pass a state smog check due to permanent fault codes which will not clear. As a result, the vehicles are not eligible to be registered in certain states.Customers may also experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, the technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set:P06E4 - Control Module Wake-Up Circuit Performance. P2797-00 - Auxiliary Transmission Fluid Pump Performance. P07B5-00 - Park Pawl Position Sensor 1 Circuit Performance. P177C-00 - Park Lock-Pawl Actuator Motor Current Sensor Performance. P288B-00 - Park Lock-Pawl Actuator Circuit Performance. Customers may also comment:Vehicle will not start when it is cold (-30°C-22°F and below). Heard and/or felt bump when the gas engine turns on while driving This software release includes the following software enhancement:Corrections to allow the vehicle to clear the permanent fault codes. Three modules are required to be flashed for this update to be effective, the following modules are all to be updated along with this HCP&AHCP update:Powertrain Control Module (PCM) Electronic Brake Booster Module (EBBM). Anti-Lock Brake System Module (ABS).
S2014000001 Rev2020-09-28. Service bulletin. FUEL SYSTEM, GASOLINE; EQUIPMENT. (Revision A) When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit.
S20140000012020-09-28. Service bulletin. ENGINE; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. When replacing the fuel line on a 2017-2018 RU 3.6L engine, it will be necessary to install a new fuel pressre sensor connector on to the vehicle harness. Follow the instructions below (or the I-sheet included with the part) when installing the connector repair kit. Improper wiring of the replacement connector can result in DTC P018D-Fuel Pressure Sensor High setting in the PCM.
90042832020-09-28. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS. TUBE, Fuel Supply If replacing Fuel Supply Tube PN 68421782A$ please refer to STAR Online publication S2014000001 for updated pressure sensor connector pin out information.
18-039-202020-05-26. Service bulletin. FUEL SYSTEM, GASOLINE. Possible Driveability Issues due to the Winter-Blend Fuel into the Warmer Season
90042442020-05-26. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE. COOLER, Transmission Oil Work procedure to address fluid leak issue with the transmission oil cooler on the MP (Part # 68249191A$), KL (Part # 68399021A$) and RU (Part # 68217322A$) needs to be followed. Service Instructions for the Condition of a TOC fluid leak: 1) Mark the leakage area if visible to assist in diagnosis and determination of the area where the leak has occurred. 2) If fluid leak was caused by damage or leakage at the transmission oil cooler: - Replace transmission oil cooler - Test drive and verify no additional fluid leaks 3) If fluid leak was caused by leak at quick connect fittings: - Replace transmission oil cooler lines - Test drive and verify no additional fluid leaks
18-089-192019-12-16. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
18-002-19 REV A2019-07-15. Service bulletin. BACK OVER PREVENTION; AIR BAGS; EXTERIOR LIGHTING; ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. A customer or technicians may be unable to read data information from the OBDII connector when using a generic scan tool (APAC).Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation, a technician may find the following DTCs have been set (NAFTA):U0418 - Implausible Data Received From Brake System Control Module 1. U0432 - Invalid Data Received From Multi-Axis Acceleration Sensor Module. P06EF - Engine Restart Performance. P06E9 - Engine Starter Performance. P00FD - Battery -B- State Of Charge Performance. C2222-68 - Improper Powerdown - Event Information. P0607-00 - ECU Internal Performance - ESM. U0402-00 - Implausible Data Received From TCM. U145D-00 - Implausible Data Received From TCM On D-PT. U1465-00 - Implausible Driver Shift Request Signal Received. U1400-00 - Implausible TPS Signal Received P1D73 - AGS Performance - (Active Grill Shutter). P0171 - Fuel System 1/1 Lean. P0174 - Fuel System 2/1 Lean. The following DTCs have been changed from a one trip fault to a two trip fault (NAFTA):P0335 - Crankshaft Position Sensor Circuit. P0339 - Crankshaft Position Sensor Intermittent. P0340 - Camshaft Position Sensor Circuit - Bank 1 Sensor 1. P0344 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 1. P0345 - Camshaft Position Sensor Circuit - Bank 2 Sensor 1. P0349 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 1. P0365 - Camshaft Position Sensor Circuit - Bank 1 Sensor 2. P0369 - Camshaft Position Sensor Intermittent - Bank 1 Sensor 2. P0390 - Camshaft Position Sensor Circuit - Bank 2 Sensor 2. P0394 - Camshaft Position Sensor Intermittent - Bank 2 Sensor 2. The technician may also find the following DTC stored in the Anti-lock Brake System (ABS) Module memory (NAFTA):The following DTC is caused by a calibration in the PCM that is in conflict with the ABS Module programming.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.