WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda CX-9

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

613 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
09-026-17-33462017-10-21. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain that the third-row seat headrest(s) are loose (A) and do not lock in the upright position (B) or the headrest are locked in the forward-bent position (C). These concerns are caused by improper operation while the seatback is folded down (A) and an excessive force is applied to the headrest (B) while it's in the upright locked position. When excessive force is improperly applied, this causes damage to the headrest lock mechanism (C).
09-023-17-33482017-10-21. Service bulletin. STRUCTURE:BODY:BUMPERS. On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider.
02-007-17-33372017-10-21. Service bulletin. SUSPENSION. Some vehicles may exhibit one or both of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the front lower arm bushing (A) making a stick-slip noise during wet road conditions. 2. A clunking noise from the front coil spring when driving over bumps. The clunking noise is due to stick-slip between the front strut bearing (B) and the coil spring (C).To eliminate the noise, the following mass-production changes have been made: 1. The coating treatment of the lower arm bushing has been changed to reduce friction and prevent stick-slip. 2. Protectors have been installed onto the coil springs to prevent stick-slip.
09-017-17-3347a2017-10-21. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tabin MAZDA CONNECT Settingsbefore performing the update.
01-007-17-33492017-10-21. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Some vehicles may exhibit a lack of engine power / intake air leak noise from the engine compartment. Hose clamps A and/or B for the air hose (C) for the turbocharger air outlet pipe (D) may be loose due to insufficient tightening. The tightening torque of the hose clamps has been increased to eliminate this concern.
SA-036-172017-10-12. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.
SA-066-172017-10-12. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:HIGH/LOW BEAM DIMMER SWITCH; FORWARD COLLISION AVOIDANCE: SENSING SYSTEM. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern. NOTE: Instrument Cluster Multi-Information Display Warning Messages vary depending on vehicle year/model. See the Owner's Manual for details.
SA-065-172017-10-04. Service bulletin. EQUIPMENT:ELECTRICAL. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command
09-017-17-3347c2017-10-04. Service bulletin. ELECTRICAL SYSTEM. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software. If the customer agrees, turn off the tachometer display on the AD-Display tab in MAZDA CONNECT Settings before performing the update.
09-036-17-33752017-10-04. Service bulletin. SEATS; SEATS:MID/REAR ASSEMBLY. On some vehicles, the second-row seat back does not fold (B) or slide (C) forward when the walk-in lever (A) is pulled up to access to the 3rd row seats. Also, the recliner lever knob (D) may not operate on some vehicles. These concerns may be caused by a disconnected walk-in lever cable. To eliminate these concerns, the design of the walk-in lever has been changed according to the following:
09-001-17-3296b2017-10-04. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS; STRUCTURE; ELECTRICAL SYSTEM. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No. 2 (C) socket covers have not been correctly installed or are missing due to improper prior repairs (i.e., customer replacing the headlamp bulbs or body shop not transferring them when replacing the headlamp unit(s) due to a collision). Any damage caused by missing socket covers, HID module seal (D), or missing bumper brackets (E) is not covered by warranty policy.
09-035-17-30802017-10-04. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the ?SpeedometerReplacement Label?.Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda?s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.With the use of SPECMO?s services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
15-005-17-33582017-10-04. Service bulletin. LANE DEPARTURE: BLIND SPOT DETECTION; VISIBILITY; ELECTRICAL SYSTEM. Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.
09-034-17-33792017-10-04. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some customers may experience the 8-inch center display sometimes turns black while driving. When the display turns black, the sound (for navigation or audio system) can still be heard and the volume can be controlled. The center display may return to normal after turning the ignition switch off, then on again. This concern may be caused by internal noise within the center display, which disturbs the integrated DC-DC converter and results in no power for the display. To eliminate this concern, the hardware for the center display has been modified.
09-023-17-3348a2017-10-04. Service bulletin. STRUCTURE:BODY:BUMPERS. On some vehicles, the front bumper cover may pop out causing a poor appearance complaint. This may be caused by an insufficient amount of holding force of the bumper slider. To eliminate this concern, the configuration of the bumper slider has been changed.
090181733512017-09-27. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom. If the condition is similar to the following "CONTROL LOGIC OF AMBIENT TEMPERATURE" or "DIFFERENCE BETWEEN THE TEMPERATURE DISPLAY AND OTHERS", advise the customer that this is a normal characteristic of the vehicle and not a malfunction. If the condition does not meet the following and the sensor malfunction is suspected, make sure to inspect the sensor according to MGSSonline or Workshop Manual (section 09-22 AMBIENT TEMPERATURE SENSOR INSPECTION). Replace the sensor only when it fails the Workshop Manual inspection.
090171733462017-09-27. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later). NOTE: For CX-9 with version earlier than 59.00.441, the tachometer function has been removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.
07005173335A2017-09-27. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some customers may complain that 1) the air conditioner is not cold enough or that 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor. The following may be the causes: 1)The A/C compressor ON/OFF control is not operating correctly, causing a problem with the air temperature control. 1)The air conditioner may not be cool enough due to inadequate amount of the refrigerant, due to leakage or overcharging. 2)The control of the amount of air blown is incorrect. To eliminate these concerns, the front and rear climate control unit software has been modified to optimize the amount of air blown and the A/C compressor ON/OFF controls.
070051733352017-09-27. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some customers may complain that 1) the air conditioner is not cold enough or that 2) the cabin is cold, but the fan speed stays on high and there is noise coming from the blower motor. The following may be the causes: 1)The A/C compressor ON/OFF control is not operating correctly, causing a problem with the air temperature control. 1)The air conditioner may not be cool enough due to inadequate amount of the refrigerant, due to leakage or overcharging. 2)The control of the amount of air blown is incorrect. To eliminate these concerns, the front and rear climate control unit software has been modified to optimize the amount of air blown and the A/C compressor ON/OFF controls.
SA-046-172017-08-25. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. An update to the MAZDA CONNECT system is now available for download from the Mazda Global Service Support (MGSS) system. The new version number is 59.00.502. Please refer to TSB 09-017/17 for a list of improvements to the system.
MT-015-172017-08-10. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
MT-014-172017-08-10. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging.
SA-063-172017-08-10. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.
SA-061-172017-08-10. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is© 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, a Mazda dealer can get the odometer setting updated to reflect the correct mileage at the time of replacement for both warranty and customer pay repairs, therefore resulting in a higher level of customer satisfaction. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
SA-058-172017-08-10. Service bulletin. VISIBILITY:WINDSHIELD. CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.