WenmarOpen by Wenmar Pro

Service bulletins for the 2019 Ford Ranger

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

140 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
TSB 22-23392022-09-23. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2021 Expedition/Navigator, 2018-2020 F-150/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to enter only the 13-digit solenoid body strategy when downloading transmission strategy.
SSM 510512022-08-30. Service bulletin. ENGINE AND ENGINE COOLING. Some 2019-2022 Ranger vehicles (equipped without an engine appearance cover) may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304 and/or P0316 stored in the powertrain control module (PCM). This may be due to water build up in the spark plug well(s) which can lead to signs of corrosion on ignition system components. To prevent reoccurrence, an engine appearance cover must be installed on the vehicle. Currently, the engine cover (SPN: L1MZ-6A949-A) is not available to order and a new engine cover kit is being released. Repair the vehicle by replacing suspect ignition system components and schedule an appointment with the customer to have an engine cover installed when the engine cover kit becomes available in November 2022. Monitor OASIS for updates
SSM 509752022-08-02. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2022 Ford/Lincoln customers may experience a notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. This occurs when the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SOC) drops below 50%. A warning may also set if the telematic control unit (TCU) has received an over the air update. The TCU powers down all communication when in this mode and app features are disabled. Manually start the vehicle to wake if from mode. More information is located in the app under: Account > Help > search 'Deep Sleep' in the entry box. If the condition remains, check the BCM 12v SOC. If the SOC does not change after charging the battery or after BMS reset is performed, continue with normal battery and/or BMS sensor diagnostics.
TSB 22-22542022-07-01. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
TSB 22-22452022-07-01. Service bulletin. POWER TRAIN. This article supersedes TSB 21-2021 to update the part list Some 2019-2020 Ranger vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0420 stored in the powertrain control module (PCM). This may be due to various software parameters within the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM and replace the catalytic converter.
SSM 508732022-06-30. Service bulletin. ELECTRICAL SYSTEM. Some 2017-2022 Ford and Lincoln vehicle owners may experience a condition of missing authorization, command and control, battery charging details or phone-as-a-key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 508632022-06-29. Service bulletin. ELECTRICAL SYSTEM. Some 2019-2022 Ranger vehicles may encounter a concern of FordPass not updating the current vehicle location and/or a battery draw is found to be from either the audio control module (ACM) or gateway module (GWM). This may be due to the software in the GWM. To correct this condition, reprogram the GWM using the latest software level of Ford Diagnosis and Repair System (FDRS). For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-22252022-06-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator, 2021 Bronco Sport and 2020-2022 Explorer/Aviator vehicles with SYNC 3 may experience various SYNC performance related concerns. This may be due to the SYNC Software. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
SSM 507932022-05-24. Service bulletin. STRUCTURE. The 2021 Ranger front fender material migrated on 22-Apr-2021 from aluminum to steel. Additionally, service replacement fenders for 2019-2022 made of aluminum are no longer available. When replacing a front fender on Rangers built on or after 22-Apr-2021, no special instructions are needed as the service replacement steel front fenders are an exact replacement component. When replacing front fenders on Rangers built on or before 21-Apr-2021, replacement of the front bumper brackets SPN: KB3Z-17C887-D (right/front) and SPN: KB3Z-17C886-D (left/front) is required to ensure proper fitment of the new steel fender. Fender apron insulators, SPN: LB3Z-16071-A(right), SPN: LB3Z-16072-A(left) The exterior appearance of the aluminum and steel front fenders are identical. The fender material do not need to match side to side on a vehicle.
SSM 507362022-05-14. Service bulletin. ENGINE AND ENGINE COOLING. 2019-2021 Ranger and 2020-2021 Explorer with 2.3L EcoBoost engines and customer concern of increased engine oil level and/or fuel smell in oil. This may occur when operating conditions do not regularly allow the oil to reach full operating temperature such as: frequent short trips, long periods of idling or driving in stop and go traffic, and/or prolonged driving in cold climates. This condition is normal and will not affect engine durability due to increased oil level or fuel content in the oil. Advise customers concerned about their engine to regularly operate the vehicle in a manner to allow the oil to reach a normal, warm operating temperature which vaporizes the fuel, and follow Intelligent Oil-Life Monitor messages that alert when the oil should be changed based on how the vehicle is operated. Refer to the owner's manual for maintenance information.
SSM 506512022-05-04. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS; EQUIPMENT. In various 2017-2022 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating "Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Please refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option
SSM 507262022-05-03. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS. Some 2017-2021 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
TSB 22-21392022-04-26. Service bulletin. POWER TRAIN; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Some 2017-2020 F-150, 2018-2022 Expedition/Navigator/Mustang and 2019-2022 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware break-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.
SSM 506422022-04-04. Service bulletin. ELECTRICAL SYSTEM:ADAS:DRIVER MONITORING:SOFTWARE. Some 2019-2021 Ranger vehicles may encounter a concern of FordPass not updating the current vehicle location. This may be due to the software in the gateway module (GWM). To correct this condition, reprogram the GWM using the latest software level of Ford Diagnosis and Repair System (FDRS). For claiming use causal part 14F642 and the applicable labor operations of Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 506292022-03-30. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; STRUCTURE:INTERIOR PANELS:DASHBOARD; EQUIPMENT. Some 2019-2020 Ranger vehicles built on or before 30-Jul-2020 may experience poor and/or no temperature change when the temperature is adjusted in the climate control system. There may also be a clicking/snapping noise from behind the instrument panel. Diagnostic trouble code (DTC) B1082 and/or B1081 may also be retrieved from the front controls interface module (FCIM). This may be due to an issue with the blend door and its controls. To avoid repeat repairs, replace the air distribution housing/heater assembly (service base part# 18478). Refer to Workshop Manual (WSM), Section 412-00. Do not replace the evaporator core for this condition. The WSM has been updated to reflect this change. Use causal part 18478 and labor operation 19700D33 of the Service Labor Time Standards (SLTS) Manual.
SSM 506032022-03-22. Service bulletin. EQUIPMENT; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Some 2019-2022 Ranger vehicles may experience condensation from the climate control system dripping on the driver's side floor and/or the driver's foot. This may be due to improper or poorly wrapped evaporator lines between the interior bulkhead and the climate control assembly case. Using a flashlight and a mirror, inspect the evaporator lines for being exposed or poorly wrapped. The cut ends of the mastic wrap should be on the top of the lines and have complete coverage. If an issue is found, cover the lines by manipulating the existing mastic wrap, or by adding more mastic to better insulate the lines and limit condensation.
SSM 505972022-03-22. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2019-2021 Ranger vehicles built on or before 09-Aug-2021 and 2021 Bronco vehicles equipped with a 2.3L engine may experience reduced engine power in freezing temperatures with an illuminated malfunction indication lamp (MIL) and/or powertrain malfunction indicator (wrench) lamp with diagnostic trouble codes (DTC) P2111, P2112, and/or P2119. This may be due to water or ice buildup in the intake manifold behind the throttle body. If suspected, remove the throttle body and inspect for water or ice in the base of the intake manifold. If water or ice is found, replace the intake manifold with part number KB3Z-9424-B and crankcase vent oil separator hose, part number LB5Z-6A664-D. Refer to Workshop Manual Sections 303-01 and 303-08. For claiming, use causal part number 9424 and applicable labor times from Section 09 of the Service Labor Times Standard (SLTS) Manual.
TSB 22-21042022-03-22. Service bulletin. EQUIPMENT:MECHANICAL; SEATS; EQUIPMENT. This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
SSM 505022022-02-23. Service bulletin. SEATS. Some 2017-2018 Focus/MKX/C-MAX, 2017-2019 MKC/Taurus/Flex/MKT, 2017-2020 Fusion/MKZ/Continental, 2017-2022 Mustang/Edge/Explorer/Police Interceptor Utility/Escape/F-150/F-Super Duty, 2018-2022 Expedition/Navigator, 2019-2022 Ranger/Nautilus, 2020-2022 Corsair/Aviator, and 2021-2022 Mustang Mach-E vehicles may exhibit a noisy, incorrectly operating, and/or inoperative seat motor. This may be due to a damaged or inoperative seat track motor. A lower level service part has been released to correct noisy, incorrect operation/inoperative seat track motors.
TSB 22-20512022-02-23. Service bulletin. POWER TRAIN. Some 2019-2022 Ranger vehicles may exhibit a shudder/vibration when accelerating from a stop. This may be due to an excessive rear axle pinion angle. To correct the condition, follow the Service Procedure steps to adjust the rear axle pinion angle.
TSB 22-20262022-02-16. Service bulletin. LATCHES/LOCKS/LINKAGES. Some 2019-2022 Ranger crew cab vehicles may exhibit excessive latching effort when returning the rear seat backrest assembly to the upright position. This may be due to oversized rear seat backrest bumpers preventing latch to striker engagement. Vehicles built on or before 04-Feb-2019 may also have excessive deadening material inside the rear seat backrest latch. To correct this condition, follow the Service Procedure to replace the rear seat backrest bumpers and adjust the striker position.
TSB 22-20252022-02-16. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Some 2019-2022 Ranger vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304 and/or P0316 stored in the powertrain control module (PCM). This may be due to water build up in the spark plug well(s) which can lead to signs of corrosion on ignition system components. To correct the condition, follow the Service Procedure to resolve the source of all DTCs and to install an engine appearance cover.
SSM 504422022-02-04. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Some 2019-2022 Ranger vehicles may experience an uneven and/or excessive gap existing between the instrument panel (IP) topper and the center tray/upfitter switch assembly. This may be due to a lack of rigidity in the IP topper not allowing the tray/upfitter switch assembly to latch properly. The following foam block service kits should be used to correct this condition. For vehicles equipped with an IP tray, order service part # KB3Z-2104338-AG, which includes a new IP tray and foam blocks. For vehicles equipped with the upfitter switch assembly, order service part # KB3Z-2104338-A, which only includes the foam blocks. If a new upfitter switch assembly is required, this must be ordered separately. Follow the installation instructions included with each kit to install the foam blocks and repair the vehicle.
TSB 21-24232022-01-01. Service bulletin. POWER TRAIN. Some 2018-2021 Expedition/Navigator, 2018-2020 F-150/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P163E stored in the powertrain control module (PCM) or transmission control module (TCM) after replacing the main control valve body. This may be due to software incompatibility between the replacement main control valve body solenoid strategy file and the PCM/TCM software. To correct this condition, follow the Service Procedure to obtain a new main control valve body with a new strategy number.
TSB 21-23572022-01-01. Service bulletin. POWER TRAIN. This article supersedes TSB 21-2315 to increase the labor operation time allowances. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.