WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Ford Mustang

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

167 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 508042022-06-01. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
TSB 22-21402022-04-26. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. Some 2015-2020 Mustang Shelby GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, follow the Service Procedure steps to replace the output shaft flange nut.
TSB 22-21042022-03-22. Service bulletin. EQUIPMENT:MECHANICAL; SEATS; EQUIPMENT. This article supersedes TSB 21-2236 to update the models and year affected. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2022 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2022 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2022 F-Super Duty, 2018-2022 EcoSport/Expedition, 2019-2022 Ranger/Nautilus, 2021-2022 Bronco/Bronco Sport/Mustang Mach-E, 2022 Maverick vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
21N102022-01-03. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Certain 2015 – 2021 Model Year Mustang Convertible Vehicles Door Opens to Secondary Latch Position n some of the affected vehicles, a front door latch may open to the secondary latched position while driving. While the door is in the secondary latched position the driver will notice wind noise from the door and a door ajar warning will appear on the instrument cluster. This concern does not result in a fully opened door while driving. The occupant can open the door normally using the door handle.
SSM 503752021-12-27. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
TSB1600662021-12-20. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Touchscreen navigation system - arabic language - blank screen
TSB1600402021-12-20. Service bulletin. ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC); SUSPENSION. GT350-R Drive selecftable suspension malfunction service required message with DTC C103E - Built on 11/01/2015 and through 12/21/2015
Service2021-12-20. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; STEERING; VISIBILITY; STRUCTURE. Online automotive service information system for March 2016
SSM 500972021-09-28. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM. Some 2016-2017 Ford and Lincoln vehicles with a new body control module (BCM) installed may exhibit a programming error when using IDS versions 122.03 through 123.01 stating 'Data Corrupt' or 'Configuration Failed, would you like to retry?'. IDS scan tool version 123.02 contains a fix for this programming error. Install IDS version 123.02 or later from PTS > Rotunda tab > Diagnostic Tool Support > Download Software. Once installed, perform the BCM programmable module installation (PMI). Refer to Workshop Manual (WSM), Section 419-10 > Removal and Installation.
SSM 500672021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 500642021-09-04. Service bulletin. SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00.
SSM 500592021-09-04. Service bulletin. ELECTRICAL SYSTEM:PROPULSION SYSTEM:CHARGING:MODULE:ONBOARD (OBCM); ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM. Some 2016-2017 Ford and Lincoln vehicles with a new Body Control Module (BCM) installed may exhibit a programming error using IDS v122.03 and newer stating "Data Corrupt" or Configuration Failed, would you like to retry?. A temporary work around has been released to complete the BCM programming process. Uninstall IDS from the computer. Run the IDS clean up utility tool located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Install IDS v122.01 (122_FULL) by copying the following link into an internet address bar https://www.fordservicecontent.com/Ford_Content/IDS/SoftwareUpdates/IDS-122.01_full.exe. Retry the BCM Programmable Module Installation (PMI) using IDS level 122.01. Monitor OASIS for updates.
SSM 500392021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
TSB 21-22362021-08-02. Service bulletin. SEATS. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement.
TSB 21-21752021-07-01. Service bulletin. ELECTRICAL SYSTEM. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F-150/Focus/C-MAX/Edge/Fiesta/MKX/Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns.
SSM 498212021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 497612021-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2021 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150F (65Å’C) or higher and engine speed is at idle up to approximately 1700 RPMs. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted.
16B102020-12-07. Service bulletin. ELECTRICAL SYSTEM. In some of the affected vehicles, the front control/display interface module (FCDIM) may have been unintentionally programmed for the European market instead of the North American market
SSM 493182020-12-04. Service bulletin. EQUIPMENT. For 2011-2020 F-150/Mustang vehicles equipped with a 5.0L engine when installing a replacement secondary timing chain tensioner (6K254) or secondary timing chain guide (6K297), it is necessary to replace both components as a pair, using the latest level parts. Make sure to use secondary timing chain tensioner part number ML3Z-6K254-A and secondary timing chain guide part number ML3Z-6K297-A.
SSM 493032020-12-04. Service bulletin. EQUIPMENT; SEATS. Some 2015-2020 Mustang vehicles may exhibit a concern of the rear seat cover appearing loose or having the foam underneath the seat cover exposed. This condition is most apparent at the front outer corners of the lower seat cushion. This may be due to the seat cover coming loose. This can be corrected by tucking the corners of the seat cushion underneath the seat cover. Any loose seat cover material can also be tucked under the cover. Replacement of the seat cushion cover is not necessary to correct this condition.
SSM 492442020-11-04. Service bulletin. SEATS:FRONT ASSEMBLY:POWER ADJUST; SEATS. Some 2015-2020 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track motor removal.
SSM 492172020-10-06. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SOFTWARE. Some 2015-2020 F-150/Mustang, 2016-2020 Edge, 2016-2018 MKX and 2019-2020 Nautilus vehicles built on or before 18-Jan-2020 may exhibit a mirror click and/or ratcheting noise when using memory functions or easy entry/exit function. This may be due to the software in the driver door module (DDM) and passenger door module (PDM). To correct the condition, reprogram the DDM and PDM with the latest software level of the appropriate Ford diagnostic scan tool. For claiming use causal part 14B291 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
SSM 490832020-09-04. Service bulletin. EQUIPMENT; POWER TRAIN. Some 2015-2017 Mustang vehicles equipped with 3.7L and 5.0L built on or before 1-Apr-2017 equipped with a 6R80 transmission may exhibit a clunk or ping noise from the driveshaft when shifting from reverse to drive or drive to reverse. A revised driveshaft which has enhanced NVH characteristics has been released. For claiming, use causal part 4R602 and applicable labor operations in section 04 of the service labor time standards (SLTS) manual.
TSB 20-22552020-09-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2016 MKS, 2016-2017 Navigator, 2016-2018 F150/Focus/CMAX/Edge/Fiesta/MKX/ Transit Connect/Mustang, 2017-2018 Continental/Fusion/MKZ, 2017-2019 Explorer, 2016-2019 Escape/MKC/Flex/MKT/Taurus/Transit/Expedition/F-Super Duty, and 2018-2019 EcoSport vehicles equipped with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.