WenmarOpen by Wenmar Pro

Service bulletins for the 2023 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

207 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 552112026-10-06. Over-the-air update. ENGINE; FUEL/PROPULSION SYSTEM; UNKNOWN OR OTHER. 2023-2026 Escape and 2025-2026 Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 1.5L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure has been added. In addition, the wastegate control actuator linkage rod with retaining clips (6K682) and actuator linkage rubber boot seal (9E416) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate control actuator assembly.
SSM 551422026-09-04. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers
25M032026-09-01. Other. UNKNOWN OR OTHER; ENGINE. Customer Satisfaction Program 25M03 Certain 2020-2025 Model Year Escape, 2021-2025 Model Year Corsair and 2022- 2025 Model Year Maverick Vehicles equipped with a 2.5L Hybrid or Plug-In Hybrid engine - Exhaust Gas Recirculation (EGR) Differential Pressure Sensor Replacement, if Required After Dealer Evaluation
25B332026-07-01. Other. ENGINE. Certain 2023-2025 Model Year Escape and Corsair, 2024-2025 Model Year Nautilus, 2025-2026 Model Year Bronco Sport and 2025 Model Year Maverick Vehicles Equipped with an Engine Block Heater System Block Heater Replacement
SSM 547382026-04-14. Service bulletin. ENGINE; POWER TRAIN. Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op
SSM 546312026-03-11. Service bulletin. ENGINE. Some 2020-2026 Escape and 2022-2026 Maverick 2.5L Duratec hybrid vehicles may require various repairs on the exhaust system. This may require removal of the exhaust heat exchanger. WSM, Section 309-00 Exhaust System > 2.5L Duratec hybrid > Removal and Installation > Exhaust Heat Exchanger has been revised to eliminate the need to remove the muffler assembly. The procedure steps and labor times have been updated to reflect this adjustment.
SSM 542882025-10-14. Service bulletin. ENGINE; POWER TRAIN. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern.
25B332025-10-03. Other. ENGINE. Certain 2023-2025 Model Year Escape and Corsair, 2024-2025 Nautilus, 2025 Bronco Sport and Maverick Vehicles Originally Equipped with an Engine Block Heater System Block Heater Element Installation
SSM 541142025-08-07. Service bulletin. ENGINE; POWER TRAIN. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers
PCM-25.12.3 Escape2025-08-05. Over-the-air update. ELECTRICAL SYSTEM; ENGINE. Software Update: Quality improvements include: -Addresses a potential Malfunction Indicator Lamp caused by two Diagnostic Trouble Codes triggered by a random engine misfire in the first thousand revolutions of vehicle start
SSM 540682025-07-30. Service bulletin. POWER TRAIN; ENGINE. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position
SSM 539732025-07-02. Service bulletin. POWER TRAIN; ENGINE. Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 539712025-07-02. Service bulletin. ENGINE; POWER TRAIN. Some 2023-2025 Escape vehicles equipped with a 1.5L/2.0L EcoBoost engine, 2023-2025 Corsair vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Nautilus vehicles equipped with a 2.0L EcoBoost engine, 2024-2025 Mustang vehicles with a 2.3L EcoBoost engine, and 2025 Bronco/Explorer/Ranger vehicles equipped with a 2.3L EcoBoost engine may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). This may be due to the spark plugs and/or ignition coils. To correct the condition, refer to Workshop Manual (WSM), Section 303-07 for normal diagnostics.
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
SSM 526442024-07-03. Service bulletin. ENGINE. Some 2023 Escape/Corsair vehicles built on or before 27-Nov-2023 equipped with 1.5L/2.0L engines may exhibit a harsh engagement after auto start/stop feature restarts the engine. This may be due to the software installed in the anti-lock brake (ABS) module. To correct this condition, reprogram the ABS module using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming use causal part number 2C219 and the applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual.
SSM 526302024-07-03. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some 2023-2024 Escape/Corsair vehicles equipped with a 1.5L or 2.0L EcoBoost engine, 2024 Mustang vehicles equipped with a 2.3L EcoBoost engine, and 2024 Nautilus vehicles may exhibit an engine misfire condition with diagnostic trouble codes (DTC) P0301, P0302, P0303 and/or P0304 set in the powertrain control module (PCM). If the codes are stored in the PCM, remove and inspect the condition of all the spark plugs. If all spark plugs are found to be free of damage, replacement of the spark plugs is not necessary. Refer to the Workshop Manual and perform normal diagnostics. If any spark plugs appear to be damaged, use a borescope to inspect the condition of the cylinder walls. If the cylinder walls are scored/scraped/damaged, replace the long block engine assembly (6006) to resolve this condition. If the cylinder walls are not scored/scraped/damaged, replace the damaged spark plug(s) and advise the customer that engineering is investigating this issue. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 525012024-05-17. Service bulletin. ENGINE. Some 2023-2024 Escape vehicles equipped with a 1.5L engine may require a cylinder head replacement as directed by other service bulletins. It is not necessary to discard the 17 valve cover bolts during disassembly; these bolts can be reused up to 3 times. The Workshop Manual (WSM), Section 303-01A, is scheduled to be updated by the end of June 2024.
SSM 523352024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed.
SSM 522192024-02-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2023-2024 Escape vehicles built on or before 11-Jan-2024 equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone
SSM 522012024-01-30. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape, 2021-2023 Corsair vehicles equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current (DC/DC) converter control module. The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC converter control module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB). To correct this condition, refer to Workshop Manual (WSM), Section 414-05 > Pinpoint Test H to verify the 300 amp high-current fuse condition. If the high-current fuse is found to be open, replace the high-current fuse per the application listing in the parts catalog. Recharge and test the 12v battery. For repairs under warranty, use the base part number of the component that caused the damage to the fuse.
23B612023-12-05. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2023 Model Year Escape and Corsair Vehicles Equipped with a 2.0L Engine - Seal Replacement for Turbocharger Coolant Return Tube to Cylinder Head
SSM 520242023-11-04. Service bulletin. HYBRID PROPULSION SYSTEM; ENGINE AND ENGINE COOLING. Some 2020-2023 Escape/2021-2023 Corsair equipped with 2.5L engine full hybrid electric vehicle (FHEV) and plug-in hybrid electric vehicle (PHEV) powertrain and 2022-2023 Maverick vehicles equipped with 2.5L engine FHEV powertrain may exhibit a condition where the 12V battery voltage is low or discharged with diagnostic trouble code (DTC) U3003:62 stored in the direct current/direct current converter control module (DC/DC). The vehicle may also exhibit DTC U3003:16 and/or U3000:04 stored in the DC/DC module. This may be due to an open in the 300 amp high-current fuse F4 located in the high-current battery junction box (BJB).
TSB 23-22742023-09-01. Service bulletin. ENGINE AND ENGINE COOLING. Some 2022-2023 Bronco Sport/Escape vehicles equipped with a 1.5L engine and 2022-2023 Corsair vehicles equipped with a 2.5L engine, built on 01-Sep-2022 and through 06-Apr-2023, may exhibit a low coolant level with engine oil in the coolant and/or coolant in the engine oil. This may be caused by an internal oil cooler leak. To correct this condition, follow the Service Procedure to test and replace the oil cooler.
SSM 517992023-07-25. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2020-2023 Escape and 2021-2023 Bronco Sport vehicles equipped with the 1.5L engine may exhibit a lugging vibration and/or boom noise while driving in gears 5-8 at approximately 1500 engine revolutions per minute (RPM). This may be felt more when the engine is under a light to moderate load. A vibration and/or boom noise could be generated from the firing frequency of the 3 cylinders or when cylinder deactivation occurs and the engine is running on 2 cylinders. This condition is more noticeable when the vehicle is driven in ECO mode. This mode was designed to deliver maximum fuel efficiency and increase the driving range.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.