Service bulletin SSM 54114
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 11021705 |
| Published by NHTSA | 2025-08-07 |
| Manufacturer's number | SSM 54114 |
| Manufacturer's date | 2025-08-04 |
| NHTSA component | ENGINE; POWER TRAIN |
NHTSA's summary
Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Engine, Transmission and driveline
Trouble codes named
P1285, P1299
| FORD ESCAPE | 2023, 2024, 2025 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 2026094 | 2026-03-03. Engine |
|---|---|
| 26V122000 | 2026-03-03. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE) |
| 2025306 | 2025-06-03. Engine |
| 25V372000 | 2025-06-03. ENGINE |
| 2025281 | 2025-05-23. Engine |
| 25V345000 | 2025-05-23. ENGINE |
| 2023309 | 2023-05-29. Engine |
| 23V380000 | 2023-05-26. ENGINE |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| SSM 55221 | 2026-10-12. Service bulletin. For 20222026 vehicles equipped with a 8F35 transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, and/or D>R) should be noted in the warranty claim. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article. |
|---|---|
| SSM 55211 | 2026-10-06. Over-the-air update. 2023-2026 Escape and 2025-2026 Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 1.5L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure has been added. In addition, the wastegate control actuator linkage rod with retaining clips (6K682) and actuator linkage rubber boot seal (9E416) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate control actuator assembly. |
| TSB 26-2428 | 2026-10-02. Service bulletin. This bulletin supersedes 25-2326. Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve. |
| TSB 26-2428 | 2026-10-02. Service bulletin. This bulletin supersedes 25-2326. Reason for update: update the service procedure to include the fuel tank isolation valve replacement, update the causal part number, and increase the labor time allowance to include the fuel tank isolation valve replacement. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software in the PCM and/or the fuel tank isolation valve. |
| SSM 55142 | 2026-09-04. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers |
| 25M03 | 2026-09-01. Other. Customer Satisfaction Program 25M03 Certain 2020-2025 Model Year Escape, 2021-2025 Model Year Corsair and 2022- 2025 Model Year Maverick Vehicles equipped with a 2.5L Hybrid or Plug-In Hybrid engine - Exhaust Gas Recirculation (EGR) Differential Pressure Sensor Replacement, if Required After Dealer Evaluation |
| TSB 26-2328 | 2026-07-20. Service bulletin. This bulletin supersedes 26-2194. Reason for update: update the Parts list to correct a part description " Loctite 638", update the claim quantity for the drain/fill plug, update the claim quantity of the wheel hub bolts (Corsair) and limited the parts list for Edge/Nautilus to only the rear drive unit fluid. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Shudder chatter condition, most noticeable at low speeds turning No relevant diagnostic trouble codes (DTCs) present This may be due to internal rear drive unit (RDU) fluid contamination. |
| 25B33 | 2026-07-01. Other. Certain 2023-2025 Model Year Escape and Corsair, 2024-2025 Model Year Nautilus, 2025-2026 Model Year Bronco Sport and 2025 Model Year Maverick Vehicles Equipped with an Engine Block Heater System Block Heater Replacement |
| SSM 54939 | 2026-06-22. Service bulletin. Some 2020-2026 Corsair/Escape, 2021-2026 Bronco Sport, and 2022-2026 Maverick vehicles equipped with an 8F35 transmission may exhibit a shudder condition, most noticeable at speeds below 60 mph (100 km/h), with no relevant diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). Sometimes, this may be perceived/felt as an engine misfire. This may be due to the torque converter. If Pinpoint Test K: Torque Converter Clutch Operation in Workshop Manual (WSM), Section 307-01 > Diagnosis and Testing > Diagnosis by Symptom directs to replace the torque converter, remove and replace the torque converter and torque converter seal. Refer to WSM, Section 307-01 > Removal and Installation > Torque Converter Seal. Remove the main control valve body. Refer to WSM, Section 307-01 > Removal and Installation > Main Control Valve Body. Overhaul and thoroughly clean the main control valve body. Refer to WSM, Section 307-01 > Overhaul > Main Control Valve Body. Reverse the removal procedure to reassemble the transmission. Install the transmission. Refer to WSM, Section 307-01 > Installation. For claim |
| TSB 26-2210 | 2026-06-05. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM) |