Service bulletin SSM 52219
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10249778 |
| Published by NHTSA | 2024-02-06 |
| Manufacturer's number | SSM 52219 |
| Manufacturer's date | 2024-01-30 |
| NHTSA component | ENGINE AND ENGINE COOLING |
NHTSA's summary
Some 2023-2024 Escape vehicles built on or before 11-Jan-2024 equipped with 1.5L engines may exhibit an Engine Coolant Over-Temperature Warning message displayed in the IPC and an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern can not be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Disconnect the charge air cooler inlet and outlet hose, overflow hose, upper and lower hose of the radiator and position these components aside. Disconnect the inlet and outlet coolant hoses of the heater core and position these compone
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Engine
Trouble codes named
P1285, P1299
| FORD ESCAPE | 2023, 2024 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 2025306 | 2025-06-03. Engine |
|---|---|
| 25V372000 | 2025-06-03. ENGINE |
| 2025281 | 2025-05-23. Engine |
| 25V345000 | 2025-05-23. ENGINE |
| 2023309 | 2023-05-29. Engine |
| 23V380000 | 2023-05-26. ENGINE |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| SSM 55211 | 2026-10-06. Over-the-air update. 2023-2026 Escape and 2025-2026 Bronco Sport vehicles equipped with a 1.5L EcoBoost engine may require removal of the turbocharger wastegate control actuator linkage for various reasons. The Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls - Turbocharger - 1.5L EcoBoost > Removal and Installation > Wastegate Control Actuator Linkage service procedure has been added. In addition, the wastegate control actuator linkage rod with retaining clips (6K682) and actuator linkage rubber boot seal (9E416) have been released as lower-level components to complete the repair without replacing the entire turbocharger wastegate control actuator assembly. |
|---|---|
| SSM 55142 | 2026-09-04. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. If the concern pers |
| 25M03 | 2026-09-01. Other. Customer Satisfaction Program 25M03 Certain 2020-2025 Model Year Escape, 2021-2025 Model Year Corsair and 2022- 2025 Model Year Maverick Vehicles equipped with a 2.5L Hybrid or Plug-In Hybrid engine - Exhaust Gas Recirculation (EGR) Differential Pressure Sensor Replacement, if Required After Dealer Evaluation |
| 25B33 | 2026-07-01. Other. Certain 2023-2025 Model Year Escape and Corsair, 2024-2025 Model Year Nautilus, 2025-2026 Model Year Bronco Sport and 2025 Model Year Maverick Vehicles Equipped with an Engine Block Heater System Block Heater Replacement |
| TSB 26-2210 | 2026-06-05. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM) |
| SSM 54738 | 2026-04-14. Service bulletin. Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op |
| SSM 54631 | 2026-03-11. Service bulletin. Some 2020-2026 Escape and 2022-2026 Maverick 2.5L Duratec hybrid vehicles may require various repairs on the exhaust system. This may require removal of the exhaust heat exchanger. WSM, Section 309-00 Exhaust System > 2.5L Duratec hybrid > Removal and Installation > Exhaust Heat Exchanger has been revised to eliminate the need to remove the muffler assembly. The procedure steps and labor times have been updated to reflect this adjustment. |
| SSM 54593 | 2026-02-27. Service bulletin. Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. |
| SSM 54288 | 2025-10-14. Service bulletin. Some 2023-2025 Escape vehicles built on or before 16-Sep-2024 equipped with 1.5L EcoBoost engine may exhibit an "Engine Coolant Over-Temperature" warning message displayed in the IPC and an illuminated MIL with DTCs P1285 and/or P1299 stored in the powertrain control module (PCM) during hard acceleration or under high load conditions. This may be due to machining chips trapped in the cylinder head causing a potential blockage in the coolant passage near the cylinder head temperature 2 (CHT2) port. To diagnose this condition, start the vehicle and idle for 15 minutes. Perform a road test at a temperature above -20°C (-4°F) and apply wide-open throttle (WOT) hard accelerations in rapid succession. If the concern cannot be replicated, drain and refill the coolant system. If the concern can be replicated, drain the coolant system. Perform the Engine Cooling System Flushing procedure in Workshop Manual (WSM) > 303-03A Engine Cooling - 1.5L EcoBoost > General Procedures. Do not use the VC1 flush additive. Reassemble the engine. Fill and bleed the coolant system and re-evaluate the concern. |
| 25H03 | 2025-10-03. Other. Harvest Program 25H03 Certain 2024 - 2025 Model Year Bronco, Bronco Sport, Corsair, Escape, Explorer, Maverick, Mustang, and Ranger Vehicles with 1.5L, 2.0L, or 2.3L Engine Spark Plug Replacemen |