WenmarOpen by Wenmar Pro

Service bulletins for the 2021 Ford Bronco

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

322 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
TSB 24-20212024-02-06. Service bulletin. EQUIPMENT. This article supersedes TSB 23-2213 to revise Figure 1, add 2024 vehicles and the part list. Some 2021-2024 Bronco vehicles may exhibit a whistle noise below the lower left windshield area at the bottom of the A-pillar. This may be due to a missed body sealer application at the factory.
TSB 23-24372024-02-06. Service bulletin. ELECTRICAL SYSTEM. This article supersedes 23-2105 to update the vehicle model years affected and customer symptoms. Some 2021-2023 Bronco vehicles may experience at least one of the following symptoms: intermittent blank/frozen center display screen that resets automatically, Android Auto Apple Carplay connectivity, checkerboard display, center display screen reset and/or Bluetooth connectivity. This may be due to the software in the SYNC module (APIM).
SSM 521972024-01-30. Service bulletin. UNKNOWN OR OTHER; WHEELS; POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2021-2024 Bronco vehicles equipped with 4x4 with part time engagement and built on or before 12-Jan-2024 may exhibit a condition of the vehicle being stuck in neutral tow mode. This may be due to a concern with the all-wheel drive (AWD) module software. Make sure the proper procedure is being followed to exit neutral tow mode by referring to the Owner's Manual > Towing Your Vehicle > Recreationally Towing Your Vehicle. Make sure the vehicle's battery is fully charged and then diagnose all diagnostic trouble codes (DTCs) in the AWD module. Refer to Workshop Manual (WSM), Section 307-07A. If diagnostics do not resolve the concern or there are no DTCs present in the AWD module, reprogram the AWD module using the latest software level of the Ford Diagnosis and Repair System (FDRS) diagnostic scan tool. Refer to the appropriate section of the WSM. Once the repair is complete, verify the vehicle's ability to successfully enter and exit neutral tow mode by cycling the vehicle in and out of neutral tow mode a minimum of two times, allowing the vehicle to enter sleep mode (key-off for at least 5 minutes) be
SSM 521782024-01-18. Service bulletin. ENGINE; UNKNOWN OR OTHER; STRUCTURE: UNDERRIDE. Some 2021-2024 Bronco vehicles may exhibit a rattle from the front windows with the windows placed in the partially down position and driving over rough roads and/or bumps. This condition is currently under investigation and repairs and/or component replacement is not expected to reduce the rattle. Inform customers that they can continue to drive the vehicle and that engineering is currently developing a solution which will be available in Q3 2024. Monitor OASIS and schedule a follow up appointment with the customer when the fix becomes available.
SSM 521662024-01-18. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; UNKNOWN OR OTHER. Some 2021-2024 Bronco vehicles equipped with SYNC 4 may experience a concern during SYNC module (APIM) programming where the vehicle's center display screen indicates: USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418.
TSB 23-24092024-01-05. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2219 to update the Parts List. Some 2021-2023 Bronco vehicles may exhibit no 3rd gear engagement and/or a grinding noise going into 3rd and/or 4th gear. This may be due to the transmission shifting system and clutch interaction such as a lack of full clutch disengagement during shifts and/or placing weight upon the gear shift lever while driving. To correct this condition, follow the Service Procedure to replace the 3rd and/or 4th gears and/or synchronizers as needed.
TSB 23-24002024-01-05. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM. This article supersedes TSB 23-2086 to update the parts list. Some 2021-2023 Bronco vehicles may encounter a Sta-bar Disconnect Service Required message in the instrument panel cluster and an illuminated warning light with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. To correct the condition, follow the Service Procedure to address water intrusion and reprogram the CHCM.
SSM 520432023-12-07. Service bulletin. EQUIPMENT. Some 2021 Bronco vehicles built on or before 01-Sep-2021 equipped with a factory soft top roof may not have the hard top roof prep kit. The prep kit includes the controls, wiring, hoses and module configurations required to have a functional rear wiper, washer and defroster. Without the prep kit installed from the factory, the rear wiper, washer and defroster, will not function. The prep kit can be identified on the window sticker as Soft-Top, Cloth W/Prep Kit under the optional equipment/other heading. This is a normal condition and no repairs/upfitting should be performed. Do not submit a claim for this condition.
TSB 23-23682023-12-05. Service bulletin. ELECTRICAL SYSTEM. This article supersedes TSB 23-2196 to update the Service Procedure. Some 2021-2022 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit various charging system error messages and/or illuminated charging system indicator displayed in the instrument panel cluster (IPC) with diagnostics trouble code (DTC) B11DB set within the body control module (BCM). This may be due to coolant contamination into the battery monitor sensor (BMS) and/or in line connector from a leaking transmission fluid heater coolant control valve. To correct the condition, follow the Service Procedure to clean the BMS connector and replace the transmission fluid heater coolant control valve.
TSB 23-23552023-12-05. Service bulletin. EQUIPMENT. This article supersedes TSB 23-2163 to update the Parts List. Some 2021-2022 Bronco vehicles built on or before 25-Jul-2022 may exhibit a rattle noise from the tailgate when driving on rough roads. The rattle may diminish with the spare tire removed. This may be due to the design of the tailgate and tailgate hinges. To correct this condition, follow the Service Procedure to replace the tailgate and the upper and lower tailgate hinges.
TSB 23-23522023-12-05. Service bulletin. POWER TRAIN. Some 2020-2023 Explorer/Aviator and 2021-2023 Bronco vehicles equipped with a 10R60 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM), the transmission solenoid ID strategy and/or sticking valves in the main control valve body. To correct the condition, follow the Service Procedure to identify and correct the condition.
23B352023-12-05. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER:MOTOR. Certain 2021-2023 Model Year Bronco Vehicles - Wiper Motor Software Update
TSB 23-23452023-11-21. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL:INFOTAINMENT. Some 2021-2023 Ford and Lincoln vehicles equipped with SYNC 4 may exhibit the navigation feature in the center display screen only displaying imperial (feet and miles) units and not being able to change to metric (meters and kilometers) units. This may be due to the software level of the SYNC module (APIM). To correct this condition, follow the Service Procedure to update the APIM to the latest software level via a coordinated flash. NOTE: The APIM software update that addresses the symptom listed in this article may have been sent via Ford Power-Up software updates delivered over-the-air (OTA) to connected vehicles that have automatic updates enabled through the center display screen. Enter the vehicle identification number (VIN) in Professional Technician System (PTS) and check the OTA Dashboard under the Connected Vehicle tab for OTA update history. If an update to the APIM has successfully completed recently and the customer is reporting the symptoms are no longer present, this article may not apply.
SSM 520362023-11-09. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; UNKNOWN OR OTHER; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2021-2023 Bronco vehicles equipped with 4x4 with part time engagement may exhibit a condition of the vehicle being stuck in neutral tow mode. This may be due to a concern with the all-wheel drive (AWD) module. Make sure the proper procedure is being followed to exit neutral tow mode by referring to the Owner's Manual > Towing Your Vehicle > Recreationally Towing Your Vehicle. Make sure the vehicle's battery is fully charged and then diagnose all diagnostic trouble codes (DTCs) in the AWD module. Refer to Workshop Manual (WSM), Section 307-07A. If diagnostics do not resolve the concern or there are no DTCs present in the AWD module, replace the transfer case and the AWD module. Refer to the appropriate section of the WSM. Once repair is complete, verify the vehicle's ability to successfully enter and exit neutral tow mode by cycling the vehicle in and out of neutral tow mode a minimum of two times, allowing the vehicle to enter sleep mode (key-off for at least 5 minutes) between each cycle. Inform customers that Ford is currently working on a software update to address this condition without a need
SSM 519892023-11-03. Service bulletin. ELECTRICAL SYSTEM. Some 2021-2023 Bronco vehicles may exhibit a charging system lamp that illuminates briefly and/or intermittently, and/or diagnostic trouble code (DTC) B11DB:08 in the body control module (BCM). This may be due to a loose fuse terminal for the 3 amp fuse in the battery positive fuse assembly. If this condition is present, compare fuse removal effort between the 3A fuse in the battery positive fuse assembly and like fuses in the under hood fuse box. If removal effort for the 3A fuse is low, replace the battery positive fuse assembly to correct this condition. Refer to Workshop Manual (WSM) Section 404-01 > Removal and Installation > Low Voltage High Current Fuse. For claiming, use causal part 14526 and M-time.
SSM 519612023-11-03. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2021-2023 Bronco vehicles may exhibit an illuminated MIL with DTCs P0096 and/or P007B in the powertrain control module (PCM), which may be more prevalent in high ambient air temperatures. For vehicles that meet this criateria, inspect the front of the vehicle for the presence of an aftermarket bumper and/or accessories which may restrict air flow to the charge air cooler and surrounding sensors. Remove the aftermarket accessory and return the vehicle to stock and reevaluate. If the concern returns with the stock bumper/accessories removed, proceed to normal Workshop Manual diagnostics.
TSB 23-23402023-11-03. Service bulletin. EQUIPMENT. This article supersedes TSB 22-2146 to update the parts list. Some 2021-2022 Bronco vehicles equipped with a soft top roof may experience paint scratches on the sports tube paint due to contact with the soft top roof frame during the open and close operation. This may be due to a lack of protective measures installed on the soft top roof frame. To correct this condition, follow the Service Procedure to install protective plates and hook and loop fasteners to sections of the soft top roof frame.
TSB 23-22822023-11-01. Service bulletin. EQUIPMENT. Some 2021-2022 Bronco vehicles built on or before 31-Mar-2022 and equipped with a factory hard top roof may have an older style latch decal installed that is no longer available to order. Replacement hard top roof panels will come with a newer style latch decal. This will create an appearance mismatch condition with the original roof panels that will still have the older style decals installed. To correct this condition, follow the Service Procedure to install newer style latch decals on all original hard top roof panels.
SSM 519392023-10-06. Service bulletin. POWER TRAIN. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P) position. A small amount of whine noise is considered to be characteristic of the 10R60/10R80/10R80 MHT/10R100 transmissions due to the offset gear drivetrain in the front support and has no effect on durability. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report if there is a customer concern of whine noise describing operating conditions and noise severity.
TSB 23-22192023-09-26. Service bulletin. POWER TRAIN. Some 2021-2023 Bronco vehicles may exhibit no 3rd gear engagement and/or a grinding noise going into 3rd and/or 4th gear. This may be due to the transmission shifting system and clutch interaction such as a lack of full clutch disengagement during shifts and/or placing weight upon the gear shift lever while driving. To correct this condition, follow the Service Procedure to replace the 3rd and/or 4th gears and/or synchronizers as needed.
TSB 23-20862023-09-26. Service bulletin. ELECTRICAL SYSTEM. This article supersedes TSB 23-2006 to update the vehicle model years affected. Some 2021-2023 Bronco vehicles may encounter a Sta-bar Disconnect Service Required message in the instrument panel cluster and an illuminated warning light with any of the following diagnostic trouble codes (DTCs) stored in the chassis control module (CHCM): C103A, C1A99, C1B03, C1B07, C1B14 and/or B1A67. To correct the condition, follow the Service Procedure to address water intrusion and reprogram the CHCM.
SU4 P3 Bronco2023-09-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE. Software Update 4 P3 for 2021-2023 Bronco Vehicles is now available. Quality improvements include: -Various Apple Carplay quality improvements
SSM 518382023-09-04. Service bulletin. ELECTRICAL SYSTEM. In various 2017-2023 Ford and Lincoln vehicles, customers may receive a message in the FordPass or LincolnWay App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the (SYNC Connect) FordPass or LincolnWay app through the TCU Embedded Modem. If this message appears, the vehicle may be equipped with a fleet telematics module. Replacement of the TCU or TCU related repairs will not prevent this message from appearing. Refer the customer to in app FordPass Guides or LincolnWay Concierge Teams to aid with fleet telematics removal. Open app, select Account > Help > CHAT or CALL option.
SSM 518632023-09-02. Service bulletin. SUSPENSION:FRONT:STABILIZER BAR; ELECTRICAL SYSTEM; ELECTRONIC STABILITY CONTROL (ESC). During replacement of the electronic front stabilizer bar disconnect assembly on 2021-2023 Bronco vehicles, removal and replacement of the sta-bar harness is required. To assist engineering with root cause analysis of failed sta-bar disconnect assemblies, include the sta-bar harness with the part in the same package when returning warranty replacement sta-bar disconnect assembly. The sta-bar disconnect assembly return should also be packaged in the original box with all protective insulators in place to properly protect it during shipping. Use the Report a Vehicle Concern link at the bottom of OASIS to submit a report with photos attached (if possible) for any front stabilizer bar disconnect concerns.
SSM 518502023-09-01. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY. Some 2021-2022 Bronco vehicles equipped with a soft top roof may exhibit loose exterior fabric on the rear window assembly. This may be due to broken D-pillar clips on the rear window. To correct the condition, replace the rear window. Refer to the Workshop Manual (WSM), Section 501-18A > Removal and Installation > Soft Top Assembly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.