WenmarOpen by Wenmar Pro

Service bulletins for the 2016 MINI Cooper Convertible

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

251 on file from NHTSA, as of 2026-10-19.

By type

By component

By topic

Bulletins, newest first
M1108152018-11-13. Service bulletin. ENGINE. Surface Cracks on the Water Pump Drive Pulley. During a repair, service or inspection, the drive pulley on the water pump shows signs of cracking. No part replacement is necessary unless there is another issue found that will be corrected by replacing the drive pulley.
M0901152018-11-13. Service bulletin. ELECTRICAL SYSTEM. New programming feature: Exclusion of Infotainment Control Units from Programming.
M6403152018-11-13. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR. "Intermittent Failure of the Blower Motor. Intermittent failure of the blower motor at high vehicle speeds and/or strong headwinds. The fault code ""0x801204 - blower output stage: Short circuit or blocked"" is stored in IHX_I1 (Heater-air conditioning control unit) sets under the following conditions: High vehicle speeds. Or Driving into strong headwind. Sunroof in the open/tilt position and/or an open side window may cause situation to occur at lower speeds. The blower resumes operation again after 60 seconds. CAUSE High wind flow and wind force causes a current overload in the blower motor."
M6402152018-11-13. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:FAN/MOTOR; ENGINE AND ENGINE COOLING. The Blower Motor is Faulty. The blower motor does not operate at any fan speed. The blower motor may work intermittently with the blower fan speed operating only on FULL speed. CAUSE The blower motor is faulty and causes the blower resistor to fail.
M6201152018-11-13. Service bulletin. STRUCTURE. Door Open Message Displayed, Even Though Door Is Closed. While driving, a CCM (Check Control Message) indicates the doors are open, even though they are closed. Also, sometimes the gong will sound and the interior lights will go on and off. The FRM (Footwell Module) sees an incorrect door lock status caused by voltage variations in the door locks.
M5107152018-11-13. Service bulletin. EQUIPMENT; STRUCTURE. Paint on the B-Pillar is Scratched/Damaged. The paint finish on the B-pillar (above the door stricker) is scratched due to the inner door cavity window seal. The door window cavity seal rubber is too hard and scuffs the B-Pillar area when opening and closing door.
M3301152018-11-13. Service bulletin. SUSPENSION; SUSPENSION:REAR:SHOCK ABSORBER. Noises from the Rear Axle Shock Absorber. The customer complains about a hammering noise from the rear axle area, when driving on rough road surfaces with low ambient temperatures. This noise will disappear with warmer ambient temperature. CAUSE Rear axle shock absorbers
M3101152018-11-13. Service bulletin. SUSPENSION. Front Axle Noise when Turning at Low Ambient Temperatures. A groaning and/or squeaking noise from the front axle occurs when turning at low speeds or idle. The noise is most noticeable at low temperatures (approx. 32 degrees F), but not at higher temperatures and after driving.
M1107152018-11-13. Service bulletin. ENGINE. "Excessive amount of water condensation may accumulate in the engine's crankcase. With prolonged vehicle storage, water condensation in engine's oil may cause oil pump malfunction. AFFECTED VEHICLES This Service Action involves F55 and F56 models (MINI Cooper with B38 engine) produced from 07/05/2014 to 02/24/2015 that are still ""new vehicles"" in dealer inventory, based on our analysis. Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Increased number of colds starts and stops during a vehicle's transportation and storage process (prior to customer delivery)."
M0110142018-11-13. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; EQUIPMENT. "MINI Motorer-Focused Satisfaction (MFS) Program. Based on Motorer feedback, MINI has determined that during the first three years of service, some vehicles may require specific additional service work to be performed. To address this issue, MINI USA, a division of BMW of North America, LLC (""MINI USA"") is providing the following Motorer-Focused Satisfaction (MFS) Program. This program's procedures have been available to you to address specific Motorers' concerns since September 1, 2014. As part of our Motorer Pledge to deliver an incredible MINI motoring experience, for the abovereferenced MINI vehicles, we developed this program to increase our Motorers' satisfaction by helping to prevent unexpected dealer service repair visits."
M6402142018-11-13. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Foul Odor when Switching On A/C. The customer states there is a foul smell when the A/C is first turned on. It lasts for five minutes. Defective coating on the evaporator, allowing bacteria to form
M3601152018-11-13. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware failure in the remote control unit (FBD3 antenna)
M1207152018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "Reduced Engine Power with Misfiring and Valvetronic Shutdown. The engine misfires with the engine power reduced, and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is displayed. Various misfire faults and the following Valvetronic fault codes are stored in the DME: ? Fault 134A02: Valvetronic servomotor: Overloading ? Fault 135302: Valvetronic servomotor: Switch-off, Component protection CAUSE DME software error"
M1206152018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "Engine Power Reduction with ""Clutch Damaged"" Faults Stored. A drivetrain malfunction check control message is displayed, prompting the customer to contact the dealer for a service visit. The vehicle drives normally, but fault(s) for a damaged clutch are stored in the DME. ? 1D3101 - Clutch: Damaged, transmittable torque too low ? 1D3201 - Clutch: Severely damaged, transmittable torque too low CAUSE 1. The DME software diagnostic for detecting excessive clutch slip is too sensitive. 2. The clutch is damaged."
M1205152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Engine Power Reduction with Electrical Wastegate Faults Stored. The Service Engine Soon (MIL) light is on, along with a check control message for engine power reduction. The following faults can sporadically be stored in the DME: B38M ? 123431 - Electric wastegate, adaptation: Limit position open implausible ? 123432 - Electric wastegate, adaptation: Limit position closed implausible B48M ? 123433 - Electric wastegate, adaptation: Adjustment range implausible The following fault can also be stored in either engine as a result of the engine power reduction: ? 120408 - Charging pressure control: Switch-off, pressure build-up blocked CAUSE DME diagnostic software
M1204152018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "?SI M12 04 15 Engine Electrical Systems June 2015 Technical Service This Service Information bulletin supersedes SI M12 04 15 dated March 2015. designates changes to this revision SUBJECT B38, B46, and B48 Engines: Engine Noise, Drivability Complaints, and Various DME Faults. The vehicle exhibits one the following complaints: ? Noise from the lower engine area, described as a high-pitched whine ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed, and will not return to the disengaged position. ? Emergency operation is active, with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"
M1102152018-11-13. Service bulletin. ENGINE. B38 and B48 Engines: Rough Running and Various Faults for Camshaft Sensor Signal and VANOS Control Stored in the DME. The engine runs rough and the malfunction warning is illuminated. One or more of the following faults are stored in the DME: 130104 Variable camshaft timing control, intake: Control fault, camshaft jamming 130108 Variable camshaft timing control, intake: Control fault, position not reached 130304 Variable camshaft timing control, exhaust: Control fault, camshaft jamming 130308 Variable camshaft timing control, exhaust: Control fault, position not reached 130E11 Intake camshaft sensor, plausibility: Signal implausible 130E20 Intake camshaft: Angle offset with respect to the crankshaft lies outside tolerance range 130F20 Exhaust camshaft: Angle offset with respect to the crankshaft lies outside tolerance range 131401 Variable camshaft timing control, exhaust, cold start: Cannot be controlled 131501 Variable camshaft timing control, intake, cold start: Cannot be controlled 131808 Variable camshaft timing control, exhaust, cold start: Position not reached 131908 Variable camshaft timing control, intake, cold start: Position not reached CAUSE DME software error and/or a mechanical failure of the VANOS actuators, camshafts and the VANOS central bolt valves.
M6601152018-11-13. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Comfort Access Inoperative. 1. Unlocking the vehicle with the Comfort Access button does not work. 2. Lowering both windows with the Comfort Access button does not work. Vehicles with option 6FP (MINI Visual Boost radio) and option 609 (Navigation Professional) are not affected. Software error
M6106072018-11-13. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. "Discharged Battery: Energy Diagnosis Must Be Performed. MINI electrical systems and advancements in vehicle technology have resulted in an increased demand on the vehicle battery. This SI will help the dealer handle ""discharged battery"" complaints. A discharged battery can have various causes, most unrelated to the battery. A failed battery is often the symptom and not the cause. A fully serviceable battery fails when an electrical component causes the battery to discharge; the battery becomes internally damaged and must be replaced. For more information, refer to http://www.batteryuniversity.com/parttwo-42B.htm. For this reason, replacing the battery is not usually a permanent repair. The cause of the discharged battery must be analyzed in order to guarantee a proper repair. To repair the vehicle properly the first time in the workshop, the diagnostic test plans must be performed to completion, with all results taken into consideration. Without performing the energy diagnosis test plan, the root cause of the discharged battery cannot be identified. This increases the chances of a repeat repair. Discharged battery."
M3101152018-11-13. Service bulletin. SUSPENSION; SUSPENSION:FRONT. Front Axle Technical Service. Front Axle Noise when Turning at Low Ambient Temperatures.
M1204152018-11-13. Service bulletin. ENGINE; ELECTRICAL SYSTEM. "B38, B46 and B48 Engines: Drivability Complaints with Crankshaft Sensor Fault. The vehicle exhibits one of the following complaints: ? Loss of power when idling ? At a higher engine speed (above 3,000 rpm), a brief decrease in the engine speed can be felt. ? Extended cranking before the engine will start ? The customer notices an increased level of ""free play"" in the clutch pedal when changing gears. ? The clutch pedal remains depressed and will not return to the disengaged position. ? Emergency operation is active with one or more of the faults listed below. Faults stored in the vehicle: ? 160020 Crankshaft sensor, signal: implausible ? 180001 Catalytic converter: efficiency too low ? 200D0C Powertrain, safety function: bus signal rpm reduction implausible ? 11A002 Fuel high pressure, plausibility: Pressure too low ? 1F054D Powertrain, safety function: powertrain reduced power, DSC-signal implausible? 120408 Boost pressure control: Shut-down as a consecutive reaction"
M1201152018-11-13. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Engine Misfire Due to Failed Ignition Coil. ? The Check Engine or Service Engine Soon (MIL) lamp is on with misfire fault(s) stored in the DME. ? Intermittent performance or rough running without a relevant DME fault stored The most likely cause is that an ignition coil has failed, which in many cases can be confirmed with basic diagnosis. During operation with high temperature fluctuations, the different materials used in the Bosch ignition coil construction can deteriorate over time, leading to a failure.
M8402142018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM; EQUIPMENT. "This Service Information bulletin supersedes SI M84 02 14 dated December 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps to keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service Action will be in effect until March 2015. Thank you for your continuous support. Improved KISU data (Customer Initiated Software Update) is now available for installation in these vehicles via the USB port. Improved functionality for COMBOX: z Detailed view of the text messages z Android device connection stability (linked contacts causing BT disconnection) Improved functionality for HU-H: z Reconnection strategy z 3rd Party App Metadata - Album art and song title Note: This Service Action is to be completed only at the dealer. You (dealers) will be receiving vehicles from the VDCs that will require this Service Action to be completed prior to customer delivery. AFFECTED VEHICLES This Service Action involves certain R5x, R6x equipped with COMBOX (CMedia), and F56 vehicles equipped with HU-H (option code 7L5). First check if a Service Action label with a code number 75 is already attached to the B-pillar. If code number 75 has been punched out, the campaign has already been performed, no further action is required. For the affected vehicles, the DCSnet Warranty Vehicle Inquiry ""Vehicle Comment"" and/or the Key Reader/ISPA Light application's ""Comments Information on"" tab has been updated to display the following message: Service Action SI M84 02 14: Bluetooth So
M8401152018-11-13. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. "SUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on. https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/20701.1.M840115....3/2/2015 Page 2 of 2 Result: z The phone reconnects to the Bluetooth system (normal). z However, the contact list is not transferred (not normal). z The contact list in the iDrive will be empty. z The call list in the Kombi will display only phone numbers, but no names. z The hands-free system works for accepting calls and conversing on calls started on the phone. Solution: z Prior to the customer entering the vehicle, he or she must unlock the phone at least once (passkey). With the release of Apple's new iPhone 6, 6 Plus and iOS 8.x software, there have been many questions regarding the new phone and software. The information in the attachment to this Service Information will help answer these questions. A printed copy can be given to the customer if needed. The attachment provides information on the differences between the new iPhone 6, 6 Plus and the previous versions, along with Apple software improvements in the following areas: 1. Visual comparison 2. Connectivity 3. Functionality Refer to the PDF file in the ""Attachment"" section of this bulletin for complete details. Information on the iPhone 6 is also available via the following website: www.miniusa.com/bluetooth NOTE: This SI will be updated as new information is received. "
M6202162018-11-13. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. PERCEIVED SCRATCH IN INSTRUMENT CLUSTER. INFORMATION Replacing the instrument cluster for this issue will NOT be covered or reimbursed under MINI limited warranties. [ Copyright (c)2016 BMW of North America, Inc. ] Page 1 of 3 Page 2 of 2 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016 Page 1 of 3 https://www.minitis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/350...9/2/2016

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.