WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Mazda CX-3

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

519 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Glass, wipers and mirrors are shown. Show all

Bulletins, newest first
SA-039-23a2023-10-05. Service bulletin. STRUCTURE; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
09-031-20b2023-08-04. Service bulletin. VISIBILITY; EQUIPMENT ADAPTIVE/MOBILITY. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
09-031/20a2023-08-04. Service bulletin. VISIBILITY; EQUIPMENT ADAPTIVE/MOBILITY. Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
00-001-232023-08-03. Service bulletin. ELECTRICAL SYSTEM; VISIBILITY; LANE DEPARTURE. In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an “as-needed” basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
09-025-232023-07-05. Service bulletin. VISIBILITY. Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at or around the washer motor (1). This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section. This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.
SA-012-232023-04-04. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; VISIBILITY. Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
SA-010-232023-03-03. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY; EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC; ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
SA-074-222022-12-02. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ELECTRICAL SYSTEM. Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.
09-014-21-3802a2021-10-31. Service bulletin. VISIBILITY:WINDSHIELD; EQUIPMENT; VISIBILITY. Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. When small pebbles/rocks are caught between the cowl grille and the windshield, deep scratches can lead to a crack in the windshield. To prevent this concern in the future, the cowl grille will be modified to reduce the pressure to the windshield.
07-005-21-38362021-10-31. Service bulletin. EQUIPMENT; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM:CONDENSOR/EVAPORATOR. Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing (A) of the evaporator (B), causing a refrigerant leak from the joint between the tubes (C) and the header (D). To eliminate this concern, the configuration of the brazing set up has been improved.
09-022-21-38152021-08-02. Service bulletin. VISIBILITY. Some customers may complain that the frequency of replenishing the window washer liquid is higher than expected, or they may complain of leakage at around the washer motor (1).This is caused by a crack that may occur at the joint section of the washer motor housing due to an inappropriate assembly process. To eliminate this concern, the design of the washer motor has been modified to not have a joint section.
SA-040-212021-07-01. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
MT-003-212021-06-29. Service bulletin. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
09-014-21-38022021-06-01. Service bulletin. VISIBILITY; UNKNOWN OR OTHER. Some vehicles may exhibit a crack in the lower center area of the windshield. This may be caused by fixtures located at the center of the cowl grille, which result in higher pressures applied to the windshield. When small pebbles/rocks are caught between the cowl grille and the windshield, deep scratches can lead to a crack in the windshield. To prevent this concern in the future, the cowl grille will be modified to reduce the pressure to the windshield.
15-005-17-3358c2021-03-08. Service bulletin. VISIBILITY; STRUCTURE. Some customers may complain that the BSM indicator light on the outer mirror glass does not illuminate when: Customer vehicle (A) is slowly passing other vehicle, even if the vehicle is still in the alert area. Adjacent vehicle (B) driving at same speed, even if the vehicle is still in the alert area. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address these customer concerns.
SA-015-212021-03-03. Service bulletin. VISIBILITY; EQUIPMENT ADAPTIVE/MOBILITY. Some customers may complain that the Blind Spot Monitoring (BSM) system is inoperative. The symptoms may include: When the ignition is switched ON, the warning indicator light turns ON momentarily and then turns off after a few seconds. The BSM system does not operate after 1st key cycle (cold soak), No DTCs stored in memory, BSM system will function normally after 2nd key cycle and the vehicle is driven on the street
07-006-172021-02-01. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; VISIBILITY. A/C blows warm air due to regrigerant leak
09-007-172021-02-01. Service bulletin. VISIBILITY. Front door window glass rattle noise
07-001-172021-02-01. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. a/c blows warm air
00-002-20-37492020-11-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM:ADAS:BLINDSPOT:SENSORS; VISIBILITY. In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on an “as-needed” basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The BSM radar aiming is performed whenever the BSM control module, the BSM bracket or the rear bumper is replaced.
09-031-20-37362020-10-03. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; VISIBILITY; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
SA-027-192019-12-20. Service bulletin. VISIBILITY; TRAILER HITCHES; EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT. Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window Deflectors - Splash Guards - Trailer Hitch - Thule Products - Wheels Locks - Aero Kit - Air Dam - Rear Spoiler - Tunnel Under Bars - Lower Arm Bar - Side Sill Extensions - Arm Rest - Illuminated Door sill Trim Plates - Interior Lighting
09-010-19-36242019-08-15. Service bulletin. VISIBILITY; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3) where attachment bolt (4) is seated. After installing the bolt (4), apply touch-up paint to the exposed base material area of the front fender stay.
MT-007-182018-08-27. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES; ENGINE; ELECTRICAL SYSTEM. ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger that is interrupting the vehicle electrical systems.
15-005-17-3358a2017-11-14. Service bulletin. VISIBILITY; ELECTRICAL SYSTEM. Some customers may complain that when passing a vehicle slowly, even if the vehicle is still in the alert area, the BSM indicator light on the outer mirror glass does not illuminate. Customers who have owned previous Mazda vehicles are more likely to complain. The BSM control module has been modified to address this customer concern.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.