WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

634 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
18-064-152018-11-19. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory.
21-004-152018-11-19. Service bulletin. POWER TRAIN; ENGINE; ELECTRICAL SYSTEM. Flash: 845RE Transmission Shift Enhancements This bulletin involves reprogramming the Transmission Control Module (TCM) with the latest available software. The following TCM calibration improvements are available for vehicles equipped an 845RE Automatic Transmission (Sales Code DFL). These updates are listed by vehicle and engine. LD and LX vehicles equipped with a 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to enable the scan tool based transmission ?Quick Learn.? ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. LX and WK vehicles equipped with a 3.0L engine (Sales Code EHD) ? Software to correct a harsh bump feel during a 2-1 downshift. WK vehicles equipped with a 3.6L engine (Sales Code ERB) ? ECO mode will not retain settings. If ECO mode is turned off, it will turn back on after the ignition is cycled. ? Software to correct a harsh bump feel during a 2-1 downshift. DS vehicles equipped with 3.6L engine (Sales Code ERB) ? Software to correct a harsh bump feel during a 2-1 downshift. ? Software to address a customer?s concern of less than desired shift quality in Four Wheel Drive (4wd) Low mode during medium to heavy acceleration. ? Software to address customer concerns of Malfunction Indicator Lamp (MIL) illumination and Diagnostic Trouble Code (DTC) P215C Output Shaft Speed, Wheel Speed Correlation setting on AWD equipped vehicles. ? Software improvements to powertrain braking in Tow/Haul mode. ? Software to improve downshift response from a medium to heavy pedal acceleration. ? Driveability improvements at higher altitudes. ? Software to improve acceleration during cruise control operation ? Software to correct a condition where DTC U11C3 - ESM Lost Communication With TCM On D-Pt CAN may have been displayed inste
07-002-152018-11-19. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
07-002-15 REV. A2018-09-24. Service bulletin. ENGINE. Idler Pulley Noise During Cold Start This bulletin involves replacing the idler pulley. The customer may describe a loud high frequency noise that happens within 20 seconds of engine startup and lasts about 90 seconds intermittently during a cold engine start, approximately 0 degrees C (32 degrees F) and below.
18-023-152018-09-24. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation
68225378A$2018-06-18. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). 3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXF long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
18-034-14 REV. A2018-06-18. Service bulletin. ENGINE. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
18-018-14 REV. C2018-06-18. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI
08-053-14 REV. A2018-06-18. Service bulletin. ENGINE. Flash: Vehicle Enhancement This bulletin involves updating the Body Control Module (BCM) software. The customer may experience one or all of the following: False security alarm activation. A significant delay to update the ambient air temperature display. Intermittently the interior lights may not turn on with the first press of the key fob. Ambient temperature may display - 40 F/-40 C for a few seconds at start up. Courtesy lamps are dim when approaching the vehicle after a remote start. Intermittently the vehicle may not start, after the vehicle has been driven and then trying to restart the vehicle with remote start. Back lighting flickers after a remote start, the condition is gone after entering the vehicle and restarting it. Engine may turn off, after the vehicle is remote started and then unlocking the vehicle with the liftgate passive entry. (Diesel Only) (Diesel Only) False DTC setting for front Daytime Running Lamps (DRL) circuit open, DRL will work properly. False setting for B16D3-15 Right DRL Lamp Control - Circuit Short To Battery Or Open. False setting for B16CF-15 Left DRL Lamp Control - Circuit Short To Battery Or Open.
90036942018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pump Assembly If error code P06DD present on any Pentastar V6 application, please inspect oil pump for relief valve failure. See photo attached. If valve is found out of place please call Bob Jackson (248) 944-0466 bob.jackson@fcagroup.com, or Joe Lovell (734) 309-6467 joe.lovell@fcagroup.com before proceeding. If unable to reach after 15 minutes record the following information and proceed with oil pump replacement and hold part for return to FCA via Fastrack system
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
18-045-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory..
18-018-14 REV. D2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: MIL Illumination Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation Performance. ? P0128-00 - Thermostat Rationality. ? P1D30-00 - Oil Viscosity Too Low. ? P200A-00 - Intake Manifold Runne
18-054-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Extended Crank, Long Crank Time. This bulletin involves inspecting the Bank 1 Camshaft Position Sensor serial number and if necessary, replacing the sensor. A small number of customers may experience an intermittent 1 to 5 second extended crank condition when starting their vehicle. No DTCs will be present when this occurs.
18-034-142018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. P0520- Engine Oil Pressure Sensor Circuit This bulletin involves replacing the oil pressure sensor with a revised part. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that the following Diagnostic Trouble Code (DTC) has been set: P0520 - Engine Oil Pressure Sensor Circuit
18-018-14 REV. B2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE
R692018-06-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. Emissions Recall R69 Selective Catalytic Reduction Catalyst Effective immediately all repairs on involved vehicles are to be performed according to this recall. Service Bulletin 18-064-15 is no longer applicable for vehicles involved in this recall. Those vehicles that have already had this repair performed, as determined by our warranty records, have been excluded from this recall. The Selective Catalytic Reduction (SCR) catalyst on about 11,400 of the above vehicles is experiencing washcoat degradation, which may lead to the exceedance of exhaust emission standards.
09-004-172018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Intermittent Engine Shudder While Driving This bulletin involves replacing the engine cylinder heads.A small number of customers may experience a slight engine shudder while driving. They may state that the condition feels and sounds like driving over rumble strips. It may also be perceived as an internal transmission issue or engine misfire. No Diagnostic Trouble Codes (DTCs) will set as a result of this condition.
18-018-14 REV. A2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P1D30 - OIL VISCOSITY TOO LOW ? P200A - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P20BA - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20EE - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P203E - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P2080 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P242B - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK1 SENSOR 3 ? P2463 - DIESEL PARTICULATE FILTER - SOOT ACCUMULATION ? P24C2 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? U12A3 - LOST COMMUNICATION WITH PM SENSOR
18-018-142018-05-21. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P200A - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P20BA - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20EE - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P203E - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P2080 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P242B - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK1 SENSOR 3 ? P2463 - DIESEL PARTICULATE FILTER - SOOT ACCUMULATION ? P24C2 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? U12A3 - LOST COMMUNICATION WITH PM SENSOR
21-006-142018-05-21. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: ELSD Module Enhancements This bulletin involves selectively erasing and reprogramming the Electronic Limited Slip Differential (ELSD) with new software. If any of the following DTC?s are either Active or Stored in the ELSD module?s memory, the ELSD motor will need to be replaced as well. C1490-00-REAR DIFFERENTIAL ACTUATOR INITIALIZATION FAILURE C148F-1D-REAR DIFFERENTIAL MEASURED MOTOR - CIRCUIT OUT OF RANGE C1489-96-REAR DIFFERENTIAL MOTOR BRAKE - COMPONENT INTERNAL FAILURE The customer may indicate that their 4X4 lamp may be flashing (indicating a malfunction of the 4X4 system).In addition, one or more of the following Diagnostic Trouble Codes (DTC) are Active or Stored in the ELSD control module?s memory. C1490-00-REAR DIFFERENTIAL ACTUATOR INITIALIZATION FAILURE C148F-1D-REAR DIFFERENTIAL MEASURED MOTOR - CIRCUIT OUT OF RANGE C1489-96-REAR DIFFERENTIAL MOTOR BRAKE - COMPONENT INTERNAL FAILURE
05048043A$2018-03-13. Service bulletin. ENGINE. PSU Exhaust Phaser 05048043AB If replacing the Exhaust Phaser for the following codes: P0340 Cam Missing/Camshaft Sensor Circuit and/or P0345 Cam Missing/Camshaft Sensor Circuit Engineering is requesting that all three Valve Timing components (Phaser, Actuator, OCV) be replaced.~ Please label the components of which bank they came from prior to parts return. ~ Phaser 05048043AB Actuator 05048045AB OCV 05048044AB Please call Joe Lovell at cell (734) 309-6467 with any questions If a response is not received within 15 mins , then proceed with diagnostics/repair.
17-004-132018-02-21. Service bulletin. SUSPENSION; ENGINE AND ENGINE COOLING; EQUIPMENT. Cleaning Of Rear Air Suspension At Every Engine Oil Change This bulletin involves cleaning the left and right side rear air spring bellows and piston area at the lower control arm pocket in the rear of the vehicle. Rear suspension air springs may become damaged due to abrasion from road debris or the air spring can become punctured due to ice/snow build-up at bottom of piston at lower control arm.
RL108213A$2017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. NAG1 (5A580) Valve Body As per Warranty Bulletin D-13-22, please use R2108213A$ valve body for all Warranty (W), Mopar (M) and Mopar Vehicle Protection (F) claims.~ Assembly also includes Filter (52108325AA) and Gasket (52108332AA).~
90036332017-11-03. Service bulletin. ENGINE AND ENGINE COOLING. Water Pump Dealers are replacing water pumps because of a coolant leak. Water pumps are found TNF but the water pump bypass o-ring was pinched resulting in a coolant leak that looks like a failed pump. Please inspect the bypass o-ring before replacing the pump as it is available separate for service.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.