Service bulletin 68225378A$
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10141261 |
| Published by NHTSA | 2018-06-18 |
| Manufacturer's number | 68225378A$ |
| Manufacturer's date | 2016-05-11 |
| NHTSA component | ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV) |
NHTSA's summary
3.0L V6 Turbo Diesel - Sales Code EXF A crankshaft locking tool marked 630 is installed on all 3.0L EXF long blocks (Lower rear left side of block under starter location). This tool locks the crankshaft at 30? ATDC. Refer to: Valve Timing ? Standard Procedure ? LOCKING ENGINE 30 DEGREE AFTER TDC IN TechCONNECT for further details. This tool must be removed after the the injection pump has been installed on the engine. The tool will be replaced with the engine block plug from the engine being removed. The engine will not turn over with this tool installed.~
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Engine, Exhaust and emissions, Crankcase ventilation (PCV)
| JEEP GRAND CHEROKEE | 2014, 2015, 2016 |
|---|---|
| RAM 1500 | 2014, 2015, 2016 |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 68079375A | 2018-11-26. Service bulletin. Crankshaft Position Sensor Before replacing this part due to a P0335 fault code, please contact Andrew Acton at cell (248) 421-4130. Engineering is interested in the condition(s) present when the fault occurs.~ If no response is received within 15 minutes, then continue with repair.~ If possible, please send Freeze Frame data and Mark Sync Event data to andrew.acton@fcagroup.com~ To Retrieve Marks Data on WiTech:~ 1) Choose ?Monitors? and select ?OBDII Monitors? from the drop down box.~ 2) At the next Screen, choose ?Cam Crank Synchronization Monitor?.~ 3) Once you select the Cam Crank Synchronization event Monitor, you will get to the three pages of Marks Event Data. |
|---|---|
| 05149141A | 2018-11-26. Service bulletin. Camshaft Position Sensor If replacing a camshaft position sensor for P0340, P0344, P0345, P0349, P0365, P0369, P0390 or P0394 fault codes, please review information below and contact Tom Nies on his cell phone: (248) 494-0187. If no response is received within 15 minutes, please continue with repair. Before clearing any codes, please pull Freeze Frame and CamCrank Sync Event Monitor data (instructions below) from the PCM and send the PDF?s to Tom Nies by email: tom.nies@fcagroup.com~ Instructions to access Cam/Crank Sync Event Monitor: - From wiTECH main screen - Monitors tab - OBDII Monitors - Select Cam Crank Synchronization Event Monitor from the list - Should bring up 3 or 4 pages of data - Click on create PDF icon in lower right corner - email PDF to tom.nies@fcagroup.com |
| SB-03-001-14 | 2014-08-26. Service bulletin. JEEP/DODGE: INFORMATION REGARDING THE LOOSENESS OF THE FRONT HALF SHAFT BOOT CLAMPS, CAUSING DEBRIS AND MOISTURE INTO CV JOINT, AND NEED TO HAVE BOTH REPLACED. MODEL 2014 DURANGO, GRAND CHEROKEE. *PE |