WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Jeep Grand Cherokee

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

634 on file from NHTSA, as of 2026-10-19.

About P2080 on the 2014 Jeep Grand Cherokee: what the code means, and the bulletins and recalls about the same components.

By type

By component

By trouble code

By topic

Only bulletins with trouble code: P2080 are shown. Show all

Bulletins, newest first
1801814REVE2022-09-26. Service bulletin. ELECTRICAL SYSTEM; SERVICE BRAKES, HYDRAULIC; EXTERIOR LIGHTING; BACK OVER PREVENTION; FUEL SYSTEM, GASOLINE. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic P0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P0171-00 - System Too Lean (Bank 1). P0172-00 - System Too Rich (Bank 1). P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P1297-00 - EGR Slow Response - Decreasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. P0088-00 - Fuel Rail Pressure Too High. P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P05F8-00 - Reductant Heater Control Module Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P0128-00 - Thermostat Rationality. P1D30-00 - Oil Viscosity Too Low. P200A-00 - Intake Manifold Runner Performance - Bank 1. P200B-00 - Intake Manifold Runner Performance - Bank 2. P202E-00 - Reductant Injection Valve Circui
18-018-142022-08-29. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; BACK OVER PREVENTION; EXTERIOR LIGHTING; SERVICE BRAKES, HYDRAULIC. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE
18-018-14 REV. B2022-08-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE
18-018-14 REV. C2022-08-15. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI
18-023-15 REV.C2022-08-08. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: P20C2-00 - Reductant Heater 3 Control Circuit Performance. P204F-00 - Reductant System Performance. P20E9-00 - Reductant Pressure Too High. P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. P241D-00 - Scr Inducement - Forced Engine Shutdown.P0420-00 - Catalyst Efficiency (Bank 1). P1297-00 - EGR Slow Response - Decreasing Flow. P208B-00 - Reductant Pump 1 Control Performance. 0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control M
18-023-15 REV.C2022-07-25. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; EQUIPMENT; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P208B-00 - Reductant Pump 1 Control Performance. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control M
18-023-15 REV-C2018-12-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. It also involves the cleaning or replacement of the Exhaust Gas Temperature (EGT) Sensor 1/2 and/or Catalyst Temperature Sensor if necessary depending on Diagnostic Trouble Codes (DTCs) that may have set. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241D-00 - Scr Inducement - Forced Engine Shutdown. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P208B-00 - Reductant Pump 1 Control Performance. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control M
18-023-15 REVA2018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2-00 - Reductant Heater 3 Control Circuit Performance. ? P204F-00 - Reductant System Performance. ? P20E9-00 - Reductant Pressure Too High. ? P249C-00 - Excessive Time To Enter Closed Loop Reductant Injection Timing Control. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P2002-00 - Diesel Particulate Filter Efficiency Below Threshold. ? P2299-00 - Brake Pedal Position / Accelerator Pedal Position Incompatible. ? P241d-00 - Scr Inducement - Forced Engine Shutdown. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Ai
18-023-152018-09-24. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: ? P20C2 - Reductant Heater 3 Control Circuit Performance. ? P204F - Reductant System Performance. ? P20E9 - Reductant Pressure Too High. ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation
18-018-14 REV. C2018-06-18. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL. Flash: MIL Illumination - Remote Start, Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Remote Start will not start the vehicle in cold 14° F (-10° C) ambient temperatures. Software enhancements will help this issue. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUI
18-018-14 REV. E2018-06-11. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: 3.0 L MIL Illumination Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set: P0087-00 - Fuel Rail Pressure Too Low. P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. P0171-00 - System Too Lean (Bank 1). P0172-00 - System Too Rich (Bank 1). P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. P1288-00 - NOX Sensor 1/2 Zero Offset Too High. P1289-00 - NOX Sensor 1/2 Zero Offset Too Low. P1296-00 - EGR Slow Response - Increasing Flow. P1297-00 - EGR Slow Response - Decreasing Flow. P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. P0088-00 - Fuel Rail Pressure Too High. P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. P0234-00 - Turbocharger Overboost Condition. P0420-00 - Catalyst Efficiency (Bank 1). P050E-00 - Cold Start Engine Exhaust Temperature Too Low. P05F8-00 - Reductant Heater Control Module Performance. P061B-00 - Internal Control Module Torque Calculation Performance. P0128-00 - Thermostat Rationality P1D30-00 - Oil Viscosity Too Low P200A-00 - Intake Manifold Runner Performance - Bank 1 P200B-00 - Intake Manifold Runner Performance - Bank 2
18-018-14 REV. D2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Flash: MIL Illumination Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - Fuel Rail Pressure Too Low. ? P20EE-00 - SCR NOX Catalyst Efficiency Below Threshold Bank 1. ? P0171-00 - System Too Lean (Bank 1). ? P0172-00 - System Too Rich (Bank 1). ? P225C-00 - NOX Sensor Performance - Signal Stuck High Bank 1 Sensor 1. ? P225D-00 - NOX Sensor 1/1 Performance - Signal Stuck Low. ? P1288-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1289-00 - NOX Sensor 1/2 Zero Offset Too High. ? P1296-00 - EGR Slow Response - Increasing Flow. ? P1297-00 - EGR Slow Response - Decreasing Flow. ? P2BA9-00 - NOX Exceedence - Insufficient Reagent Quality. ? P2080-00 - Exhaust Gas Temperature Sensor Circuit Performance. ? P2084-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 2. ? P0426-00 - Catalyst Temperature Sensor Circuit Performance Bank 1 Sensor 1. ? P242B-00 - Exhaust Gas Temperature Sensor Circuit Performance-Bank 1 Sensor 3. ? P062B-00 - Internal Control Module Fuel Injector Control Circuit Performance. ? P0088-00 - Fuel Rail Pressure Too High. ? P016F-00 - Closed Loop fuel Pressure Control At Limit - Pressure Too Low. ? P009A-00 - Intake Air Temperature / Ambient Air Temperature Correlation. ? P0234-00 - Turbocharger Overboost Condition. ? P0420-00 - Catalyst Efficiency (Bank 1). ? P050E-00 - Cold Start Engine Exhaust Temperature Too Low. ? P05F8-00 - Reductant Heater Control Module Performance. ? P061B-00 - Internal Control Module Torque Calculation Performance. ? P0128-00 - Thermostat Rationality. ? P1D30-00 - Oil Viscosity Too Low. ? P200A-00 - Intake Manifold Runne
18-018-14 REV. B2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set erroneously: ? P0087-00 - FUEL RAIL PRESSURE TOO LOW ? P0088-00 - FUEL RAIL PRESSURE TOO HIGH ? P016F-00 - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P009A-00 - INTAKE AIR TEMPERATURE / AMBIENT AIR TEMPERATURE CORRELATION ? P0234-00 - TURBOCHARGER OVERBOOST CONDITION ? P0420-00 - CATALYST EFFICIENCY (BANK 1) ? P0426-00 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P050E-00 - COLD START ENGINE EXHAUST TEMPERATURE TOO LOW ? P05F8-00 REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B-00 - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B-00 - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P0128-00 - THERMOSTAT RATIONALITY ? P1D30-00 - OIL VISCOSITY TOO LOW ? P200A-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B-00 - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P202E-00 - REDUCTANT INJECTION VALVE CIRCUIT PERFORMANCE ? P203E-00 - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P204F-00 - REDUCTANT SYSTEM PERFORMANCE ? P2080-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084-00 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P20BA-00 - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20BE-00 - REDUCTANT PRESSURE LINE HEATER CONTROL CIRCUIT PERFORMANCE ? P20EE-00 - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P20C2-00 - REDUCTANT HE
18-018-14 REV. A2018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a condition that the Oil Life Monitor shows faster then expected oil life deterioration. Software enhancements will address this issue. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P1D30 - OIL VISCOSITY TOO LOW ? P200A - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P20BA - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20EE - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P203E - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P2080 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P242B - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK1 SENSOR 3 ? P2463 - DIESEL PARTICULATE FILTER - SOOT ACCUMULATION ? P24C2 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? U12A3 - LOST COMMUNICATION WITH PM SENSOR
18-018-142018-05-21. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Flash: MIL Illumination - Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Some customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find that any of the following Diagnostic Trouble Code(s) may have been set: ? P0073 - AMBIENT AIR TEMPERATURE SENSOR CIRCUIT HIGH ? P0088 - FUEL RAIL PRESSURE TOO HIGH ? P016F - CLOSED LOOP FUEL PRESSURE CONTROL AT LIMIT - PRESSURE TOO LOW ? P0420 - CATALYST EFFICIENCY (BANK 1) ? P0426 - CATALYST TEMPERATURE SENSOR CIRCUIT PERFORMANCE (BANK 1 SENSOR 1) ? P05F8 - REDUCTANT HEATER CONTROL MODULE PERFORMANCE ? P061B - INTERNAL CONTROL MODULE TORQUE CALCULATION PERFORMANCE ? P062B - INTERNAL CONTROL MODULE FUEL INJECTOR CONTROL CIRCUIT PERFORMANCE ? P200A - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 1 ? P200B - INTAKE MANIFOLD RUNNER PERFORMANCE - BANK 2 ? P20BA - REDUCTANT HEATER 1 CONTROL CIRCUIT PERFORMANCE ? P20EE - SCR NOX CATALYST EFFICIENCY BELOW THRESHOLD BANK 1 ? P203E - REDUCTANT LEVEL SENSOR 1 CIRCUIT INTERMITTENT/ERRATIC ? P2080 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE ? P2084 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK 1 SENSOR 2 ? P242B - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT PERFORMANCE - BANK1 SENSOR 3 ? P2463 - DIESEL PARTICULATE FILTER - SOOT ACCUMULATION ? P24C2 - EXHAUST GAS TEMPERATURE MEASUREMENT SYSTEM - MULTIPLE SENSOR CORRELATION BANK 1 ? P24F2 - EGR TEMPERATURE/CHARGE AIR COOLER TEMPERATURE CORRELATION ? U12A3 - LOST COMMUNICATION WITH PM SENSOR

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.