Service bulletins for the 2023 Ford F-150
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
482 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| TSB 24-2070 | 2024-04-03. Service bulletin. POWER TRAIN. Some 2023 F-150 vehicles equipped with a 10R80/10R80 MHT transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the software in the powertrain control module (PCM) or transmission control module (TCM) or sticking valves in the main control valve body. |
|---|---|
| TSB 24-2068 | 2024-04-03. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN; ELECTRICAL SYSTEM. Some 2023 F-150 vehicles equipped with 3.5L PowerBoost engine and F-150 Lightning vehicles receiving a replacement Anti-Lock Brake System (ABS) module may experience an error during the FDRS Programmable Module Installation (PMI) routine which states Procedure Unsuccesful - GetFlashActionPartNumbers Unable To Obtain Flash Action Part Numbers From Available Topology. This may be due to the software level of the powertrain control module (PCM) and/or the secondary on-board diagnostic module C (SOBDMC). |
| TSB 24-2054 | 2024-04-03. Service bulletin. ENGINE AND ENGINE COOLING. This article supersedes TSB 23-2194 to add Figure 1 and update the parts list. Some 2022-2023 F-150 vehicles built on 23-August-2022 and through 30-April-2023 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt. |
| SSM 52345 | 2024-03-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 52340 | 2024-03-20. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:CONTROL UNIT/MODULE. Some 2023 F-150 Raptor/Tremor vehicles may exhibit failed programmable module installation (PMI) using the Ford Diagnosis and Repair System (FDRS) when installing a new ABS module. This may be due to the software within the new ABS service replacement part. To correct this condition, when installing a new ABS module during normal Workshop Manual (WSM) repair and diagnosis, use service part PL3Z-2005-B and perform part installation and PMI per the WSM, Section 206-09 Anti-Lock Brake System (ABS) and Stability Control, Removal and Installation, Electric Brake Booster (EBB). For claiming, use causal part 2005 and applicable labor operations in Section 02 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 52335 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed. |
| SSM 52334 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2. |
| SSM 52333 | 2024-03-20. Service bulletin. ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM. Many body control module C (BCMC) warranty return parts are coming back with no trouble found. To verify that the BCMC is at fault prior to replacing, perform the following. First, disconnect the battery then check all BCMC connectors for terminal pushout, pin damage, spread terminals, and corrosion. Refer to Workshop Manual Section 100-00 Wire Terminal Inspection and Replacement. If none found, reconnect the BCMC and battery terminals then recheck functionality. If concern still exists, proceed with BCMC replacement. |
| SSM 52328 | 2024-03-20. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; EQUIPMENT:ELECTRICAL:INFOTAINMENT. Some 2021-2024 Bronco/F-150, 2023-2024 Escape/F-Super Duty vehicles equipped with SYNC 4 may experience a concern during accessory protocol interface module (APIM) programming where the vehicle's center display screen indicates USB Error. This may be due to a lack of memory space available to perform the APIM software update. If it is a memory concern, the Ford Diagnosis and Repair System (FDRS) will provide an option to delete the voice application. Re-enter the module programming and when prompted, do not select first option - SYNC Module (APIM) Software Update, select the second option - Delete Voice Application(s) From Module. Once deleted, run the SYNC Module (APIM) Software Update as directed, this will update the software and automatically reload the voice app. If the voice delete option is not available, continue with normal diagnostics in the Workshop Manual, Section 418. |
| SSM 52314 | 2024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure. |
| SSM 52313 | 2024-03-20. Service bulletin. TRAILER HITCHES. Some 2021-2023 F-150 vehicles may exhibit DTCs B1D08:11 and/or B1D09:11 stored in the trailer module (TRM) with a Trailer Brake System Fault See Manual message in the instrument panel cluster (IPC) when a trailer is not connected to the vehicle. This may be due to water intrusion at the back side of the trailer tow connector. Inspect connector C4099 and the trailer tow connector (14489) for signs of corrosion or damage. If corrosion or damage is present at either connector, replace the female side of the C4099 connector using service pig tail kit (3U2Z-14S411-JXC) and the trailer tow connector. If corrosion or damage is not present, refer to the Workshop Manual (WSM) Section 417-01 Exterior Lighting, Diagnosis and Testing for additional diagnosis. For claiming, use causal part 14489 and applicable labor operations in Section 01 of the Service Labor Time Standards (SLTS) Manual. |
| OTAPU0813DORUP2 | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update 23-PU0813-DOR-UP2 for 2022-2023 MY F-150 vehicles is now available. Quality Improvements include: - Robustness action to improve the windows and mirror switches loss of functionality. |
| OTAPU1129CBCODPL | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update PU1129- CBC-ODP for 2022-2023 MY F-150 Lightning vehicles is now available. Quality improvements include: - Robustness action to prevent Voltage Unstable Fault issue in BECM/HV Battery. - Prevent a false positive overtemperature DTC & MIL on dash. - Prevent AutoSAR wake requests after key off. |
| OTAPU0105CMRFXF | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update 24-PU0105-CMR-FX for 2022-2023 MY F-150 vehicles is now available. Quality Improvements include: - Robustness action to increase availability of BlueCruise |
| OTAPU0102SVDFXF | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update 24-PU0102-SVD-FX for 2023 MY F-150 vehicles is now available.Quality improvements include: - Ford Blue Cruise Map expiration removal update - Adds a "some display features may be temporarily unavailable" message to the SYNC screen when a SYNC update is installing. |
| OTAPU0105CMRFXL | 2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. Software Update 24-PU0105-CMR-FX for 2022-2023 MY F-150 Lightning vehicles is now available. Quality Improvements include: - Robustness action to increase availability of BlueCruise |
| OTAPU1113UNXDCL | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update 23-PU1113-UNX-DC for 2022-2023 MY F-150 Lightning vehicles is now available. Quality Improvements include: - Restores TCU module DID vehiile specific configuration which were set to default values in previous OTA update. |
| OTAPU1009-SS-NS | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION:SOFTWARE. Software Update PU1009-SS-NS for 2021-2023 MY F-150 vehicles is now available. Quality Improvements include: - Robustness action in operation of vehicle to detect low-state-of-charge battery and prevent engine stall, as well as provide improved warning to customers when low-state-of-charge conditions exist. - Eliminates potential Emergency Parking Brake activation when wire harness experiences a short. - Robustness action to prevent potential line pressure drift DTC from setting. -Eliminate potential ABS Yaw Rate Calibration issue. -Robustness action to alleviate the Nuisance SSN (Stop Safely Now) message from setting and vehicle should operate as expected in the next Key Start event. -Eliminates potential Emergency Parking Brake activation when wire harness experience a short. |
| OTAFPUPU1113UNX | 2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. Software Update 23-PU1113-UNX-DC for 2021-2023 MY F-150 vehicles is now available. Quality Improvements include - Restores TCU module DID vehicile specific configuration which were set to default values in previous OTA update. |
| TSB 24-2039 | 2024-03-07. Service bulletin. ELECTRICAL SYSTEM. This article supersedes TSB 24-2020 to add minor feature code HUKAJ to the required vehicle criteria. Some 2021-2023 F-150 vehicles equipped with the minor feature code HUKAJ (400 watt direct current/alternating current (DC/AC) inverter system with a pickup bed alternating current (AC) power outlet socket) may experience the DC/AC inverter system inoperative with diagnostic trouble code (DTC) B1330:9A stored in the body control module (BCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to a connection issue at C4628 |
| 23B84 | 2024-03-05. Service bulletin. VISIBILITY:WINDSHIELD. Certain 2022 - 2023 Model Year F-150 Vehicles - Windshield Water Leak Inspection Adding owner letter. Other documents submitted 02/01/24 |
| 23B71 | 2024-03-05. Service bulletin. POWER TRAIN. Certain 2023 Model Year F150, Expedition, Navigators equipped with 8.8 inch Front Axles - Front Axle Assembly Replacement |
| 23B21 S1 | 2024-03-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Certain 2023 Model Year F-150 and Bronco Vehicles - Gateway Module Programing |
| SSM 52295 | 2024-03-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2021-2023 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, be sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging newly installed engine-to-transmission spacer plate. |
| SSM 52280 | 2024-03-05. Service bulletin. EQUIPMENT. Some 2021-2024 Mustang Mach-E, 2022-2024 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.