Service bulletins for the 2023 Ford F-150
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
482 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| SSM 55228 | 2026-10-12. Service bulletin. ENGINE; UNKNOWN OR OTHER. Some 2020-2026 Aviator/Explorer/F-150/Bronco/Ranger vehicles equipped with a 2.7L or 3.0L (non-diesel) engine may need the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation. |
|---|---|
| TSB 26-2233 | 2026-05-18. Service bulletin. ENGINE. This article supersedes TSB 26-2116 to clarify the prior approval statement. Some of the vehicles listed in the model statement above may exhibit an oil leak from the oil filter adapter to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt. |
| SSM 54795 | 2026-05-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM; POWER TRAIN. Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates. |
| TSB 26-2116 | 2026-04-14. Service bulletin. ENGINE. This article supersedes TSB 25-2323 to update the Service procedure, Parts list, and add a clarification note about Cost Cap and Prior approval process requirement for vehicles under NVLW. Some of the vehicles listed in the model statement above may exhibit an oil leak from the oil filter adapter to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt. |
| SSM 54678 | 2026-04-06. Service bulletin. ENGINE. Some 2021-2026 F-150 vehicles equipped with a 5.0L/5.2L engine, 2021-2025 F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis vehicles equipped with a 6.8L/7.3L engine and 2021-2025 E-Series/F-650/F-750 vehicles equipped with a 7.3L engine may exhibit a rattle/scraping noise upon startup that may remain after the engine is running. Workshop Manual (WSM), |
| TSB 25-2569 | 2025-12-01. Service bulletin. POWER TRAIN; ENGINE. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P0301-P0306, P0201-P0206 and/or various other powertrain DTCs stored in the PCM. This may be due to the engine harness contacting the hose crimp end or spring clamp tangs on the exhaust heat exchanger heater hose assembly. |
| SSM 54392 | 2025-12-01. Service bulletin. ENGINE; POWER TRAIN. Some 2021-2025 F-150/Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit diagnostic trouble code (DTC) P0299 stored in the powertrain control module (PCM) and may also exhibit a rattle noise from the turbocharger. This may be due to the wastegate actuator rod being disconnected. Workshop Manual (WSM), Section 303-04 Fuel Charging and Controls > Turbocharger has been added to address this condition to allow servicing of the turbocharger actuator rod. In addition, the wastegate actuator rod and associated retention springs and clips have been released as lower level components to complete the repair without replacing the entire turbocharger actuator assembly. |
| SSM 54363 | 2025-11-13. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN; ENGINE. Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L/3.5L (non hybrid)/6.8L/7.3L engine and 2021-2026 E-Series may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated to address this condition. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis. |
| SSM 54275 | 2025-10-14. Service bulletin. ENGINE. Some 2021-2023 Explorer vehicles equipped with a 3.0L EcoBoost engine, 2021-2023 Aviator vehicles equipped with a 3.0L EcoBoost or 3.0L plug-in hybrid electric vehicle (PHEV) engine, 2021-2023 Edge/Nautilus vehicles equipped with a 2.7L EcoBoost, 2021-2024 F-150 vehicles equipped with a 2.7L EcoBoost, and 2021-2024 Bronco and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine. This noise may occur on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to an internal component of the variable cam timing (VCT) unit. Workshop Manual (WSM), Section 303-00 > Diagnosis and Testing > Engine > Pinpoint Test F has been updated to include additional steps along with a video to identify the affected VCT unit that requires replacement. |
| SSM 54269 | 2025-10-08. Service bulletin. ENGINE. Some 2021-2025 Expedition/Navigator/F-150/F-Super Duty/F-53 Motorhome/F59 Commercial Stripped Chassis/F-650/F-750/Transit vehicles equipped with a 2.7L,3.5L EcoBoost (non-hybrid), 3.5L Cyclone, 6.8L or 7.3L engine, may exhibit a rattle/scraping noise from the bellhousing area on start-up. Workshop Manual (WSM), Section 303-00 Engine System - General Information > Diagnosis and Testing and 303-06 > Starting System has been updated. Additionally, WSM, Section 303-01 > Removal and Installation > Engine to Transmission Spacer Plate has been added to address this condition. Refer to the revised WSM sections for normal diagnosis. |
| TSB 25-2399 | 2025-09-03. Service bulletin. ELECTRICAL SYSTEM; FUEL/PROPULSION SYSTEM; ENGINE. This article supersedes TSB 23-2412 to update the labor times from M-time to AP-time and add a limit. Some of the vehicles listed in the Model statement above may exhibit an illuminated engine coolant temperature warning lamp with a "Motor Coolant Over Temperature" message in the instrument panel cluster (IPC) with diagnostic trouble code (DTC) P0A2F:94 stored in the secondary on-board diagnostic control module C (SOBDMC). This may be due to the software level of the SOBDMC. |
| 25N05 | 2025-08-02. Other. ENGINE. Certain 2021-2023 Model Year F-150 HEV Vehicles Replacement of Exhaust Gas Heat Recovery Coolant Spigot In the affected vehicles, the Exhaust Gas Heat Recovery (EGHR) coolant spigot may develop a crack due to a weaker-than-intended coolant spigot having been used in a prior repair. As a result, coolant may leak out of the engine, and one or more warning lights, such as the Check Engine Light, may illuminate. |
| TSB 25-2323 | 2025-07-24. Service bulletin. ENGINE. This article supersedes TSB 25-2087 to update Vehicle Application adding 2025 Model Year. Some of the vehicles listed in the model statement may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity or a block crack just below the oil filter adapter near the main bearing cap outer bolt. |
| SSM 54009 | 2025-07-08. Service bulletin. POWER TRAIN; ENGINE. Some 2023-2025 F-150 Raptor vehicles equipped with a 5.2L engine may exhibit an exhaust rattle/rasp on a cold start. The Workshop Manual (WSM), Section 309-00 Exhaust System - 5.2L 32V Ti-VCT - Supercharged > Diagnosis and Testing > Exhaust system > Pinpoint Test D: Noises Such As Buzzing, Drumming, Thumping, Ringing Or Hissing Coming From Exhaust System has been updated to address exhaust rattling sounds during a cold start lasting for 5 seconds or less as a normal condition. For concerns with exhaust rattles lasting longer than 5 seconds, follow WSM Section 309-00 Exhaust System - 5.2L 32V Ti-VCT - Supercharged > Diagnosis and Testing > Exhaust system. |
| SSM 53973 | 2025-07-02. Service bulletin. POWER TRAIN; ENGINE. Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly. |
| SSM 53764 | 2025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush. |
| TSB 24-2278 | 2024-09-19. Service bulletin. ENGINE. This article supersedes TSB 24-2227 to update the labor operation number. Some 2022-2024 F-150 vehicles built on 23-Aug-2022 and through 29-Mar-2024 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt |
| SSM 52772 | 2024-08-16. Service bulletin. ENGINE. Some 2020-2024 F-150, 2021-2024 Bronco, and 2024 Ranger vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit. |
| TSB 24-2227 | 2024-07-29. Service bulletin. ENGINE. This article supersedes TSB 24-2166 to update the parts list. Some 2022-2024 F-150 vehicles built on 23-Aug-2022 and through 29-Mar-2024 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt. To correct the condition, follow the Service Procedure to inspect the engine block for a porosity leak. |
| TSB 24-2166 | 2024-06-04. Service bulletin. ENGINE. This article supersedes TSB 24-2054 to add 2024 models and update the production fix date. Some 2022-2024 F-150 vehicles built on 23-Aug-2022 and through 29-Mar-2024 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt. To correct the condition, follow the Service Procedure to inspect the engine block for a porosity leak. |
| SSM 52447 | 2024-05-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2020-2024 F-150 and 2021-2024 Bronco vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit a ticking/tapping or rattle type noise from the top front cover area of the engine on initial start-up after a cold soak of 6 hours or more that may last for 2-5 seconds. This may be due to a stuck internal component of the variable cam timing (VCT) unit. To correct the condition, replace all 4 of the VCT units following Workshop Manual (WSM), Section 303-01. For claiming, use causal part 6C525 and applicable labor operations in Section 6 of the Service Labor Time Standards (SLTS) Manual. If labor times are not available, claim M-time. |
| TSB 24-2054 | 2024-04-03. Service bulletin. ENGINE AND ENGINE COOLING. This article supersedes TSB 23-2194 to add Figure 1 and update the parts list. Some 2022-2023 F-150 vehicles built on 23-August-2022 and through 30-April-2023 equipped with a 5.0L engine may exhibit an oil leak from the oil filter adaptor to engine block mounting area. This may be due to block porosity just below the oil filter adapter near the main bearing cap outer bolt. |
| SSM 52335 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. For 2015-2024 Ford and Lincoln vehicles equipped with turbocharged engines and customer concern of an engine oil leak, refer to Workshop Manual (WSM), Section 303-00 for oil leak inspection and testing methods. Ford has evaluated turbochargers replaced for oil leak symptoms and although oil may collect on the external surface of a turbocharger, it is extremely rare for a turbocharger assembly to be the root cause of the oil leak. Careful inspection of the turbocharger oil feed and drain tubes should be performed along with the recommended WSM procedures as needed. Warranty claims for turbocharger replacement going forward will be assessed. |
| SSM 52334 | 2024-03-20. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2024 Mustang and F-150 vehicles equipped with a 5.0L engine may exhibit a tick tap and/or typewriter ticking noise at idle after an engine oil change. It is often referred to as typewriter noise because of its similarity to the sound of a mechanical typewriter. The noise in question may be heard on some engines when engine temperatures reach 150°F (65°C) or higher and engine speed is at idle up to approximately 1700 RPM. It can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. The typewriter noise tick rate can be faster or slower and is not detrimental to the engine function or durability and has no short or long term effects on the engine. This an operating characteristic of the 5.0L engine and no repairs should be attempted. This information along with an example audio clip has been added to the WSM Section 303-00 Engine System General Information > Diagnosis and Testing > Engine > PPT F > Step F2. |
| SSM 52295 | 2024-03-05. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2021-2023 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, be sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging newly installed engine-to-transmission spacer plate. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.