WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ford Escape

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

146 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
TSB1600452021-12-20. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE. 2.0L Ecoboost - Fuel odor
TSB1600012021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN; AIR BAGS; STRUCTURE. 49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
LTR37562021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; AIR BAGS; ENGINE; STRUCTURE; POWER TRAIN; ELECTRICAL SYSTEM. 49 CFR Part 579.5 Monthly Communications - January 2016
SSM 492102020-10-06. Service bulletin. ENGINE AND ENGINE COOLING. Some 2009-2020 Ford and Lincoln vehicles equipped with turbochargers may exhibit an oil leak from the turbocharger oil supply or return tubes, O-rings or 6.7L pedestal gasket. Although oil may collect on the turbocharger, it is very rare for a turbocharger to leak oil. To isolate the source of the leak, refer to Workshop Manual (WSM), Section 303-00 General Information > Diagnosis and Testing > Engine > Engine Oil Leaks - Fluorescent Oil Additive Method procedure. When an oil leak is present at a turbocharger oil supply or drain tube, remove the affected oil tube and inspect for damage, and replace the O-ring seals, pedestal gasket or oil tube as required. Refer to WSM, Section 303-04. For claiming, use the affected oil tube or pedestal gasket as the causal part and applicable labor operations in Sections 6 and 9 of the Service Labor Time Standards (SLTS) Manual.
TSB 19-22872019-10-04. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2016 Escape vehicles equipped with a 1.6L EcoBoost engine may exhibit a lack of cooling caused by the A/C inlet line breaking at the compressor. This may be due to the oil cooler coolant lines exerting excess pressure on the A/C inlet line. When replacing the A/C inlet line, a support clip for the oil cooler coolant line should be installed to prevent contacting the A/C inlet line. To correct the condition, follow the Service Procedure steps to replace the A/C inlet line and adjust the gap between the A/C inlet line and the CAC hose.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 477102019-03-04. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM:SOFTWARE. Some 2014-2015 Escape, 2015 C-Max and Focus vehicles equipped with integrated remote start may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0116 in the powertrain control module (PCM) immediately following a remote start event. Vehicles may also display a warning message stating Engine Coolant Over Temperature. This condition may occur when remote start is used and the vehicle is allowed to time out (engine shuts off). Reprogram the body control module (BCM) using the latest software version of the appropriate Ford diagnostic scan tool. For claiming, use causal part 12A648 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
TSB 18-22552018-09-24. Service bulletin. ENGINE. Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 470002018-06-11. Service bulletin. ENGINE; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 470002018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 469372018-01-29. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. Some 2013-2016 Escape vehicles equipped with a 1.6L EcoBoost engine may require the replacement of the A/C suction line. When replacing the suction line, verify that all of the compressor to engine block fasteners are installed and torqued properly. The compressor requires three fasteners - 2 bolts (W701331-S442) and one stud/nut - installed securing it to the engine block and torqued to 25 Nm (18 lb.ft) per the Workshop Manual (WSM), Section 412-00 under removal and installation. Improper number of compressor fasteners and/or incorrect torque may cause repeat failure of the A/C suction line connected to the compressor.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
TSB 17-00342017-05-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. SOME 2013-2017 ESCAPE VEHICLES BUILT ON OR BEFORE 28-FEB-2017 MAY EXHIBIT A NOISE AND/OR VIBRATION FROM THE CLIMATE CONTROL BLOWER MOTOR WITH OR WITHOUT A LACK OF AIRFLOW FROM PANEL REGISTERS AND MAY ALSO HAVE AN ODOR. THIS CONCERN MAY BE DUE TO SMALL ANIMALS THAT CAN ENTER THE BLOWER MOTOR HOUSING AREA THROUGH THE AIR INLET DUCT AND CAUSE DAMAGE TO THE AIR INLET DUCT ASSEMBLY AND/OR BLOWER MOTOR ASSEMBLY. THE SMALL ANIMALS MAY DEPOSIT FOREIGN MATERIAL IN THE BLOWER MOTOR ASSEMBLY AND AIR INLET HOUSING THAT MAY CAUSE LACK OF AIRFLOW, NOISE AND/OR VIBRATION. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
SSM 463272017-03-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ENGINE. 2013-2016 FIESTA, ESCAPE, TRANSIT CONNECT AND 2013 FUSION VEHICLES WITH A 1.6L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE MAY EXHIBIT AN ENGINE OIL LEVEL READING THAT IS UP TO 8 MM ABOVE THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK WHEN THE ENGINE IS FILLED WITH THE CORRECT AMOUNT OF OIL. THIS IS A NORMAL CHARACTERISTIC OF THIS ENGINE. DO NOT LOWER THE OIL LEVEL TO THE MAXIMUM MARK ON THE ENGINE OIL DIPSTICK IF THE ENGINE CONTAINS THE CORRECT AMOUNT OF OIL. ADDING OIL IS NOT REQUIRED IF THE LEVEL IS ABOVE THE MINIMUM MARK ON THE ENGINE OIL DIPSTICK. REFER TO THE OWNERS MANUAL FOR PROPER ENGINE OIL CAPACITY.
SSM 462952017-03-15. Service bulletin. ENGINE. TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.
SSM 459222017-02-11. Service bulletin. ENGINE. SOME 2013-2016 ESCAPE VEHICLES EQUIPPED WITH 2.5L ENGINE MAY EXHIBIT A ROUGH IDLE, LOW RPM AT IDLE OR A STALL ON HOT RESTART WITH NO DTCS IN SELF TEST. THIS MAY BE DUE TO THE A/C COMPRESSOR CLUTCH BEING SEIZED. IF A VEHICLE COMES IN FOR THIS CONCERN, CHECK THE A/C COMPRESSOR TO SEE IF IT IS ENGAGED DURING START UP/INITIAL RUN. THE PCM STRATEGY KEEPS THE A/C COMPRESSOR CLUTCH OFF FOR 5 SECONDS ON INITIAL START. IF SO, REPLACE THE COMPRESSOR ASSEMBLY (CV6Z-19703-L). IF NOT, PERFORM NORMAL DIAGNOSTICS IN THE PC/ED.
TSB16-01012017-02-10. Service bulletin. ELECTRICAL SYSTEM; ENGINE. SOME 2013-2014 FOCUS ST, FUSION, ESCAPE AND VEHICLES EQUIPPED WITH A 2.0L GASOLINE TURBOCHARGED DIRECT INJECTION (GTDI) ENGINE AND BUILT ON 9/1/2012 AND THROUGH 8/1/2013 MAY EXHIBIT AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODE (DTC) P2096 (POST CATALYST FUEL TRIM SYSTEM TOO LEAN BANK 1) STORED IN POWERTRAIN CONTROL MODULE (PCM) MEMORY. THIS MAY BE DUE TO ENGINE OIL MIGRATING FROM THE VARIABLE VALVE TIMING (VVT) OIL CONTROL SOLENOIDS THROUGH THE ENGINE WIRE HARNESS TO THE CATALYST MONITOR SENSOR (CMS). FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
16-00312016-06-22. Service bulletin. ELECTRICAL SYSTEM; ENGINE. ISSUE Some 2013-2014 Focus ST, Fusion, Escape and MKZ vehicles equipped with a 2.0L gasoline turbocharged direct injection (GTDI) engine and built on 9/1/2012 and through 8/1/2013 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2096 (post catalyst fuel trim system too lean bank 1) stored in powertrain control module (PCM) memory. This may be due to engine oil migrating from the variable valve timing (VVT) oil control solenoids through the engine wire harness to the catalyst monitor sensor (CMS).
15-01622016-06-22. Service bulletin. ENGINE. SUMMARY TO BE PROVIDED ON A FUTURE DATE.
TSB-14-01822015-08-03. Service bulletin. ENGINE. FORD: DURING HIGHWAY SPEEDS OF 64-88 KM/H (40/55 MPH), SOME VEHICLES WITH ALL WHEEL DRIVE (AWD) WILL EXPERIENCE A WHINNYING IN THE REAR DRIVE UNIT (RDU). MODEL 2013-14 ESCAPE. *PE
15-00702015-07-28. Service bulletin. ENGINE. FORD 2013-2015 ESCAPE: BULLETIN INFORMATION INVOLVING VEHICLES EQUIPPED WITH 1.6L GASOLINE TURBOCHARGED DIRECT INJECTED ENGINE BUILT BEFORE 3/13/2015 MAY EXPERIENCE AN ENGINE IDLE SURGE AT ON COLD START, REPROGRAMMING THE PCM MAY CORRECT THE ISSUE. *LJ
ASI-445512014-10-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:TORQUE CONVERTER; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION. FORD: AT BOTTOM OF TRANSMISSION HOUSING IS ACCUMULATION OF FLUID AND IF ITS STICKY AND HONEY COLORED LIKELY EXCESSIVE GREASE APPLIED TO TORQUE CONVERTER HUB OR RUST INHIBITOR APPLIED TO FLEXPLATE AT TIME OF MANUFACTURING. MODEL 2013-2014 ESCAPE, FUSION. *PE
ASI-445532014-10-02. Service bulletin. ENGINE. FORD: THE OUTBOARD RIGHT HAND CYLINDER HEAD TO BLOCK TOFRONT COVER T JOINT IS LEAKING ENGINE OIL. MODEL 2013-2014 FWD. *PE
CSP-13B142014-09-29. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). FORD: DUE TO CONFUSION OF OVERFILLING CRANKCASE CAPACITY OF 1.6 ENGINES, WITH OTHER ENGINES, IN SOME VEHICLES, ENGINE WOULD VIBRATE OR HAVE EXCESSIVE OIL IN POSITIVE CRANKCASE VENTILATION (PCV) SYSTEM AND ENGINE AIR INTAKE SYSTEM. MODEL 2014 ESCAPE. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.