WenmarOpen by Wenmar Pro

Service bulletins for the 2012 BMW 328i

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

623 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
1305142018-11-26. Service bulletin. ENGINE. . INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function Structure." 3. Select "01 Engine." 4. Select "Engine electronics MEVD." 5. Select "Misfire detection." 6. Follow the steps in the test plan and select "Basic check (start)" first. Do not select "Additional check" at this time. 7. If the result of the "Basic check" indentifies a fuel system component failure, replace the identified component. If the result of the "Basic check" test plan was inconclusive, go to step 7. After the component replacement, perform the "Basic check" portion of the test plan again to verify if the diagnosis was correct and the vehicle condition has been rectified.
1301142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING. N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active. This would cause any of the following additional faults to be stored, depending on the SCR system status at the time. 2C4E00 - SCR system: System error and poor urea/water mixture quality detected 26FD00 - Reducing agent metering, long-term adaptation: Adaptation value too high 29FB00 - SCR system, warning and deactivation scenario: Warning level 1 29FC00 - SCR system, warning and deactivation scenario: Warning level 2 CAUSE Unfavorable DDE software
1221102018-11-26. Service bulletin. FUEL SYSTEM, GASOLINE. N51 Engine: Service Engine Soon Lamp Illuminated - Loss of Power and Various Faults Stored in the DME. The customer complains that the Service Engine Soon lamp is illuminated. The vehicle has lost power; the engine cranks but will not start; and various faults are stored in the DME for engine misfire and/or mixture adaptations. CAUSE The vehicle has lost fuel system delivery pressure due to a loose or split fuel line inside the fuel tank. The failure is related to an unfavorable stacking of tolerances between the rubber fuel hose and the plastic regulator nipple or deterioration of the rubber hose construction material.
5115112018-11-26. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:CONCEALMENT DEVICES. Headlight Washer Nozzle Cover Sticks Out.
6520122018-11-26. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. RAD2plus: Radio Causes Battery Drain. The vehicle's battery state of charge is very low after the vehicle was parked for a longer period of time (e.g., overnight). The RAD2+ radio doesn't allow the vehicle to enter full sleep mode, and causes a current draw from the battery with ignition off.
6517122018-11-26. Service bulletin. SEAT BELTS; SEAT BELTS:FRONT:WARNING LIGHT/DEVICES; EQUIPMENT; AIR BAGS. Check Control Message "Restraint System Faulty" Is Displayed. Intermittently the check control message "Front Passenger Restraint System Faulty" is displayed in the Central Information Display. The following information is read from the vehicle: 1. Key Reader Vehicle Defects Details shows DTC: 930AB3. 2. ISTA fault code "930AB3-POL: indicator lamp for passenger airbag deactivation: short-circuit to plus" The fault condition is not present. 3. ISTA check control message ID 109 CAUSE FZD (Operating Unit for Roof) software error causes the POL (Passenger Airbag Off Lamp) to intermittently malfunction.
6510122018-11-26. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Headunit-Basic: CID is blank and "NO SIGNAL" is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. ??Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-B Error in the Headunit-Basic (HU-B), also called Radio Professional or ENTRY head unit.
6503132018-11-26. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT. Headunit-Basic: All CD Tracks Are Displayed as "track 0" After Restart. INFORMATION Do not replace parts and do not perform a repair attempt! Note: The issue is rectified after a different CD is inserted into the in-dash CD drive. Explain to the customer that this only happens when the vehicle is turned off with CD mode active. This Service Information will be updated as soon as a solution is available. Software solution is expected to be available with ISTA/P 2.50.1 in July 2013. New integration level: F020-13-07-501 or higher WARRANTY INFORMATION Not applicable.
6502132018-11-26. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Headunit-Basic Does Not Start Up and "BMW" Is Permanently Displayed. The Headunit-Basic (HU-B), also called Radio Professional or the ENTRY head unit, does not start up and "BMW" is permanently displayed on the CID (Central Information Display). No fault code is stored in the head unit. Hardware issue in the HU-B
6203132018-11-26. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Basic Instrument Cluster: Display Is Intermittently Inoperative. The display in the basic instrument cluster is intermittently inoperative. The following fault codes are stored in the instrument cluster: * B7F6B4 "Instrument cluster: Error in the display unit when switching off (NO SIGNAL)" and/or * B7F6AA "Display switch-off error when starting up" Software error in the instrument cluster
6201132018-11-26. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. All Gauges and Displays in Instrument Cluster Inoperative. All gauges and displays in the instrument cluster are inoperative, including the following: * Speedometer * Revolution counter * Fuel gauge * Engine oil temperature * No check control messages displayed ??No board computer information displayed Note: A power cycle does NOT rectify the issue. Software error in the instrument cluster
5110112018-11-26. Service bulletin. EQUIPMENT; STRUCTURE:EMERGENCY:ESCAPE/EGRESS/EXIT. Anti-trap Is Activated when Raising the Front Side Windows. When closing the front side windows using the convertible top switch or the central power window switch, one or both front side windows come to a stop at the top third travel area, and then reverse direction slightly. When the switch is actuated again, the windows will close normally. CAUSE The front side windows contact the rear side windows, causing the anti-trap feature of the front side windows to trigger.
3201122018-11-26. Service bulletin. STEERING. Teile Clearing for Steering Systems.
1224122018-11-26. Service bulletin. ENGINE. N20 and N26 Engine: DME FC CDA904 FA CAN Message State Trailer 0x2E4 Is Missing.
1222122018-11-26. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ENGINE; POWER TRAIN. Service Action: Program Control Units. When coming to a stop, there is the possibility of an unfavorable judder. This is due to the software parameters for downshifting and transmission clutch control. CAUSE Unfavorable vehicle software
1110122018-11-26. Service bulletin. ENGINE. ?N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding internally.
1214122018-11-26. Service bulletin. ENGINE. SI B12 14 12 October 2014 Engine Electrical Systems Technical Service This Service Information bulletin supersedes SI B12 14 12 dated February 2014. designates changes to this revision SUBJECT N51, N52K, N52T and N55 Engine: Various Faults Stored in DME Related to VANOS and Camshaft Position. A rattling noise can be heard from the engine compartment; the engine loses power; and the Service Engine Soon lamp is illuminated. One or more of the following faults may be stored: E70, E71, E82, E88, E90, E91, E92 and E93: 2A7C - VANOS, inlet, cold start 2A82 - VANOS, intake, variable cam control test 2A7A - VANOS, exhaust, cold start 2A87 - VANOS, intake: control fault, camshaft sticking 2D5A - VANOS, intake: control fault, camshaft sticking 2D5B - VANOS, intake: control fault, position not reached 2D54 - VANOS, exhaust, cold start: not controllable 2D55 - VANOS, intake, cold start: not controllable 2D60 - VANOS, exhaust: control fault, camshaft sticking 2D61 - VANOS, exhaust: control fault, position not reached 2D9F - Camshaft input sensor: signal implausible 2DA1 - Camshaft exhaust sensor: signal implausible 300C - Camshaft input sensor: signal high 300D - Camshaft input sensor: signal low 300E - Camshaft exhaust sensor: signal high 300F - Camshaft exhaust sensor: signal low F07, F10, F12, F13 and F25: 130104 - VANOS, intake: control fault, camshaft sticking 130108 - VANOS, intake: control fault, position not reached 130304 - VANOS, exhaust: control fault, camshaft sticking 130308 - VANOS, exhaust: control fault, position not reached 130E11 - Camshaft input sensor: signal implausible 130F11 - Camshaft exhaust sensor: signal implausible 164020 - Camshaft input sensor: signal high 164021 - Camshaft input sensor: signal low 164030 - Camshaft exhaust sensor: signal high 164031 - Camshaft exhaust sensor: signal low CAUSE One or both (intake and/or exhaust) of the VANOS gear assemblies may have faulty assembly bolts. One or more of the four assembly bolts have loosened or broke
1120142018-11-26. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Delivery Stop: Crankcase Failure. A Delivery Stop has been issued on certain 2015 model year vehicles with N20/N26 engines produced from September 4, 2014 through October 21, 2014. These vehicles may have a crankcase failure. Approximately 145 vehicles are affected.
1114142018-11-26. Service bulletin. ENGINE. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
0703142018-11-26. Service bulletin. EQUIPMENT. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer. Where diagnosis (vehicle or short test) with ISTA has already started, it is important to diagnose the fault code(s) listed below (when they are stored in the vehicle) during the current workshop visit. This will help lead to a reduction in workshop repeat repair visits and higher customer satisfaction.
0110142018-11-26. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Engine Camshaft (VANOS) Adjustment Units: Limited Warranty Extension to 10 Years Without Mileage Limitation. INFORMATION BMW of North America, LLC ("BMW NA") is extending the limited warranty for the Camshaft (VANOS) Adjustment Units on certain model BMW vehicles equipped with the non-turbocharged 6-cylinder engine to: 10 years without mileage limitation, as determined by the vehicle's original in-service date. This "component-specific" limited warranty extension applies to defects in materials and workmanship and is subject to the applicable New Vehicle/SAV Limited Warranty's exclusions and limitations, in addition to the vehicle and coverage eligibility requirements. This bulletin is notice of a "limited warranty extension." This is NOT a notice of a Recall or Service Action. There is no immediate repair required unless the BMW vehicle is currently experiencing this problem.
B6126172018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Charging of the high voltage battery is interrupted and will not complete. A change in the job structure in ISTA causes the BDC to open the 30B relay unexpectedly.
B6125172018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. SME - HV BATTERY CELL MODULE VOLTAGE FAULTS. When diagnosing with ISTA or ISTA Next, a fault code (detailed below), regarding the cell voltage measurement, is entered in the battery management electronics (SME). ? 21F0C2 - High-voltage battery, cell supervision circuit 1: Voltage measurement (battery cell), line disconnection ? 21F0C3 - High-voltage battery, cell supervision circuit 2: Voltage measurement (battery cell), line disconnection ? 21F0C4 - High-voltage battery, cell supervision circuit 3: Voltage measurement (battery cell), line disconnection ? 21F0C5 - High-voltage battery, cell supervision circuit 4: Voltage measurement (battery cell), line disconnection ? 21F0C6 - High-voltage battery, cell supervision circuit 5: Voltage measurement (battery cell), line disconnection The customer might not have reported the situation as the fault code could have no effect on the vehicle operation. Erroneous fault in the fault memory of the SME, possible fault in a cell supervision circuit (CSC) or a cell module.
B6124172018-11-26. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; ELECTRICAL SYSTEM. "?STEERING WHEEL BUTTONS DO NOT FUNCTION RELIABLY. ? Sporadic or continuous malfunction of multifunction steering wheel buttons ? CC Message ""Cruise control without function"" displayed ? Sporadic or continuous malfunction of shift paddles Frictional corrosion on connector line (wiring harness) between switch cluster and steering wheel"
B4103162018-11-26. Service bulletin. STRUCTURE:BODY:DOOR. EDGE CORROSION IN THE INNER DOOR JAMB AREA. Corrosion on inner door panels at the following holes and cavity openings: ? Door brake (1). ? Door wiring harness pass-thru (2).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.