WenmarOpen by Wenmar Pro

Service bulletin LI54.30-P-070482

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10177561
Published by NHTSA2020-07-27
Manufacturer's numberLI54.30-P-070482
Manufacturer's date2020-06-18
NHTSA componentEQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; ELECTRICAL SYSTEM:SOFTWARE

NHTSA's summary

The check engine indicator light in the instrument cluster may be illuminated with one of the following fault codes: P261029, P02FF85, or P02FF02 stored in the engine control unit (N3/10). The time in instrument cluster is implausible due to an internal reset. If no other complaints exist then check for and perform any available software updates for the following control units: - Motor electronics (N3/10) - Powertrain control unit (N127) - Instrument cluster (A1) If all three control units have the latest software installed and the complaint continues to occur then proceed with replacement of the instrument cluster (A1) Should the complaint re-occur after the instrument cluster has been replaced then open a PTSS case with the following information: - Control units logs for the ME, PTCU, and IC - Initial quick test

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Engine, Equipment and accessories, Transmission and driveline, Automatic transmission, Instrument cluster, Software

Trouble codes named

P02FF, P2610

Vehicles listed
MERCEDES-BENZ AMG E63S2020
MERCEDES-BENZ AMG GLC432020
MERCEDES-BENZ AMG GT2020
MERCEDES-BENZ AMG GT S2020 (the catalog's model; the bulletin names a series or trim of it)
MERCEDES-BENZ AMG GT532020 (the catalog's model; the bulletin names a series or trim of it)
MERCEDES-BENZ AMG GT632020 (the catalog's model; the bulletin names a series or trim of it)
MERCEDES-BENZ AMG GT63S2020 (the catalog's model; the bulletin names a series or trim of it)
MERCEDES-BENZ AMG S632020
MERCEDES-BENZ AMG S652020
MERCEDES-BENZ C 3002020
MERCEDES-BENZ C 3502020
MERCEDES-BENZ CLS 4502020
MERCEDES-BENZ E 3502020
MERCEDES-BENZ E 4502020
MERCEDES-BENZ E63 AMG2020
MERCEDES-BENZ G 5502020
MERCEDES-BENZ G632020
MERCEDES-BENZ GLC 3002020
MERCEDES-BENZ S 4502020
MERCEDES-BENZ S 5502020

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
22V3650002022-05-20. COMMUNICATION: AUTO CRASH NOTIFICATION; ELECTRICAL SYSTEM:SOFTWARE
21V0580002021-02-05. ELECTRICAL SYSTEM:SOFTWARE; COMMUNICATION: AUTO CRASH NOTIFICATION
20V3950002020-07-06. ELECTRONIC STABILITY CONTROL (ESC); ELECTRICAL SYSTEM:SOFTWARE

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
LI00.20-P-0776152024-04-05. Service bulletin. The following symptoms may be present in the instrument cluster: 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. Routine change in software in instrument cluster N133/1. Vehicle handover has not taken place. First manually commission the already installed instrument cluster control unit N133/1 and then perform the special procedure to re-initialize ASSYST data in powertrain control unit N127. NOTE: The information contained in this document is intended for use by trained, professional technicians with the knowledge to properly and safely perform diagnosis and repairs on Mercedes-Benz vehicles, using Mercedes-Benz approved tools and equipment. It informs service technicians about conditions that could occur in certain vehicles and provides information that could assist in proper vehicle diagnosis, service, or repair. It does not indicate that a defect is present in any vehicle referenced in this document nor does it imply warranty coverage. DO NOT assume that a symptom or condition, or a described cause of a symptom or condition, affects any particular vehicle or groups of vehicles, or that a described repair applies to any particular vehicle or groups of vehicles. There can be multiple causes resulting in the same or similar symptoms or conditions described in this document, and trained professional service technicians must use their diagnostic skills to make evaluations on a case-by-case basis. The information contained in this document does not guarantee warranty coverage nor does it extend the vehicle’s warranty in any way.
OTA-242402012024-03-04. Service bulletin. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY20-23 A-Class, C-Class, CLA, CLS, E-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module will receive an OTA update to improve the system stability and allow for better accessibility of Mercedes me services. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit. All customers have been mailed a letter informing them of this OTA software update.
LI82.85-P-0768002023-11-03. Service bulletin. The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in N112/9 control unit for telematics services (HERMES). Software update for control unit N112/9 - Control unit for telematics services (HERMES) to software release E522.8. If, against expectations, the erroneous display of the message in the instrument cluster continues to occur following the update, please create a TIPS case.
NCU-HU SW Update2023-09-01. Service bulletin. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background. The installation will eliminate software errors for a better entertainment experience. The update will show after the ignition has been cycled. MBUSA will conduct an OTA service campaign. A workshop visit for the customer is not required since remote software updates are automatically downloaded and installed in the customer’s vehicle. The OTA may be validated as successful on the customer’s Mercedes Me connect app under “Over-the-Air Vehicle Updates” as “Update for the communication module”. If the OTA is successful it will show a green “installed” and date of installation in the Over-the-Air update section.
LI46.15-P-0633532022-08-04. Service bulletin. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2. Perform software update of driver's seat control unit
LI2700P0731242021-10-25. Service bulletin. Transmission diagnosis using th eIntelligent Predictive Repair (IPR) tool.
NCU-20200800052020-09-21. Service bulletin. Mercedes-Benz AG ("MBAG"), the manufacturer of Mercedes-Benz, has determined that on certain MY19-20 C-Class, GLC-Class, and AMG GT (205, 253, and 290 platform) vehicles, the software for the AMG drive unit control unit does not correspond to the current series production configuration. As a result, noise may occur from the engine mounts. An authorized Mercedes-Benz dealer will update the software as necessary.
SC-20191100032019-12-23. Service bulletin. Update sound system control unit software