WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Mercedes-Benz AMG GT

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

139 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
OTA-Comm. Mod. SW. Update2026-10-06. Over-the-air update. ELECTRICAL SYSTEM. A software update will be performed that provides enhancements to the robustness and system stability of the communication module. The update is free of charge and runs in the background, which takes about 8 minutes to install. During this time, the vehicle can be driven without any restrictions, and the new software will be active with the next ignition cycle. Remedy MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not require a dealer visit.
LI54.71-P-0791042026-10-02. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("‑ ‑"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the re‑check function in the same location. NOTE: Updated head unit software for AMG's has NOT been released yet. ETA 12/2026. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: • Video of the concern. • Exact location (latitude and longitude is best)
LI54.21-P-0803262026-10-02. Service bulletin. ELECTRICAL SYSTEM. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2‑ 3 key cycles. The vehicle can be released back to the customer.
LI54.71-P-0791042026-09-02. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("‑ ‑"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Update head unit software to latest version and the re‑check function in the same location. If vehicle is still exhibiting one of the symptoms as described exactly as in the complaint section or as shown in the video attachments, open a TIPS case to the Body/Chassis/Entertainment inbox with the following: • Video of the concern. • Exact location (latitude and longitude is best)
LI54.10-P-0808802026-08-14. Service bulletin. ELECTRICAL SYSTEM. Complaint Customer Complaint: - AC charging is not possible. - The departure time, charging pause, location-based charging or target SOC limit is automatically set to 50% or to a random value in the Mercedes me application or in the charging settings on the head unit display. (Picture 1 & 3) - Incorrect notifications appear in the Mercedes me application for charging-related functions. (Picture 2) Related DTCs in quick test: No related fault codes (DTCs) are stored in the relevant control units. CPC3 - N127 (Drivetrain control unit) OBL223_GEN4 - N83/11 (Alternating current charger for high-voltage battery) DCB223 - N116/5 - Direct current charge connection unit (DCCU) Picture1 The target SOC limit is automatically set to 50% or any random values during charging. Picture 2 Incorrect notification Example “Unable to unlock charging cable. Picture 3 Incorrect settings of charge interruption or pause. (If applicable) Cause - The Customer shares their Mercedes me credentials (password) with a third-party application, for example, a wall box application. This causes the Mercedes Benz backend server to receive random requests to reset the maximum SOC, departure time, charging pause, etc. - Charging settings are set incorrectly, for example, incorrect departure time, charging program, charging interruption/ pause, etc. Remedy The remedies below may vary depending on the customer complaint. Refer to the remedy that best matches the customer complaint. Remedy 1: The target SOC limit is automatically set to 50% or to random values during charging. - Change the Mercedes me login password on the Mercedes me homepage. (My Account > Login and Security > Reset). (Refer to Annex 1). Previously granted authorizations should then be revoked so that the charging settings can no longer be changed by external applications. Advise customers not to share the new password again. - Are there any sub-users? If yes, revoke their rights and reassess the function. -If differences between the vehicle and the Mercedes me app are visible, a new synchronization is recommended. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. Remedy 2: Incorrect notifications in the Mercedes me app for charging-related functions. - Restart synchronization between the app and backend. Turn off Digital Extras through the Mercedes me app or the MMCR portal, and then turn the services on again. (Refer to Annex 2) Remedy 3: Incorrect charge interruption or pause setting. - Perform a factory reset of the head unit (A26/17). (Home > Functions > System > Reset), or turn off/correct all charging settings. (Refer to Annex 3) Additional Information: (Good to know) The LED on the charging inlet or socket indicates whether charging is completed or paused. 1) If the target SOC is reached, the charging inlet LED lights up Blue/Green without flashing. 2) If charging is paused, the charging inlet LED lights up orange without flashing. Additionally, the head unit charging settings display a charging pause. Note: Do not replace any hardware components for these complaints. If the complaint cannot be solved, please contact via TIPS or CAC.
LI54.65-P-0801322026-08-12. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics. Cause Various root causes Remedy See attached diagnostic guide.
LI82.60-P-0808062026-08-11. Service bulletin. ELECTRICAL SYSTEM. Complaint DAB, FM, or SDARS radio reception is limited, only a few stations are found. Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.
LI82.60-P-0808062026-07-27. Service bulletin. ELECTRICAL SYSTEM. Complaint After an "Over the Air" update (OTA), FM or SDARS radio reception is limited; only a few stations are found. Cause The firmware installation was incomplete. Remedy In the A26/17 control unit "MBUX multimedia system" (head unit), use XENTRY to carry out the special process "All Modules"; this will reinstall the firmware completely.
LI54.21-P-0803262026-07-24. Service bulletin. ELECTRICAL SYSTEM. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167, 465: SW has been released. Update the FSAM to the latest SW version. 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.
LI54.71-P-0791042026-07-14. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q3 2026.
PSL-NCU Return Parts 7/32026-07-13. Other. SERVICE BRAKES; STRUCTURE:BODY; ELECTRICAL SYSTEM. Dear Mercedes-Benz USA Dealers, The part numbers listed in the chart below should no longer be installed, and any existing stock must be returned to your facing PDC. The deadline for all dealer returns is no later than Thursday, July 23rd, 2026. After July 23rd, returns of these parts will no longer be accepted. These parts should be returned via ZSR Special Return, using item category SCM Authorized Part Return. Please include a copy of this NCU as your authorization to return these parts. This procedure will not affect your return allowance. All returned parts will be replaced in accordance with the chart provided below.
LI00.20-P-0776152026-07-06. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. The following applies to model series 167 from AEJ 22/1 onward, 192 AMG, 206, 214, 223, 232 AMG, 236, 254, 290 AMG from AEJ 23 onward, 294, 295, 296, 297 and 465: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI54.21-P-0803262026-07-06. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Complaint CEL light on with no drivability concerns. Cause Signal timing error. Remedy 167: SW has been released. Update the FSAM to the latest SW version. 465, 290, 118, 243, 247: Software is still in development. This fault code does not cause a drivability concern and will clear itself within 2-3 key cycles. The vehicle can be released back to the customer.
ANN Interm. Issues Flash2026-07-02. Other. ELECTRICAL SYSTEM. We are experiencing intermittent issues when flashing A26/17 - MBUX multimedia system + Instrument cluster (Head unit) when using flashing method ethernet to USB-C. Until further notice, please flash via VCI only.
LI00.20-P-0784242026-06-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The remaining time shown on the instrument cluster in the workshop menu (days to next due service) is implausible (>365 days) for the following conditions: • for the date of the vehicle handover • or the last conducted and confirmed Service A/B Cause Case 1: Observe the following on vehicles with a disconnected on-board electrical system battery (12V/48V): • The period in which the on-board electrical system battery is disconnected cannot be counted by the maintenance computer. • As soon as the on-board electrical system battery is connected again, the maintenance computer automatically starts counting without making a correction to the remaining time (days until the next service). Case 2: If a disconnected on-board electrical system battery (12V/48V) can be ruled out as the cause, it is possible that: The daily turnover counter inside the electronic ignition lock (EIS) has experienced memory loss. This anomaly was detected in the EIS software from modification year 2022 onward. To do this, please check the plausibility of the daily turnover counter as follows: If "TUSZ Assyst Plus" < the actual days since "Handover Date/DAY/Month/Year," then proceed to remedy for case 2. Information: A variation of 2-3 days is still considered plausible. If "TUSZ Assyst Plus" is plausible, or if a remaining time of 365 days is permanently displayed, check whether the vehicle has been handed over. These types of cases have different causes. (The respective values are included in the maintenance data in the control unit log of the instrument cluster). Remedy For case 1: When the on-board electrical system battery is disconnected, this period must always be taken into account for these vehicles, and the following condition must be met for a correct calculation to be made: • (A): The number of days from the "date of vehicle handover or last service A/B" to the "date on which the vehicle arrived at the workshop." • (B): Remaining time (days until the next service, as shown in the instrument cluster). • (C): Days on which the on-board electrical system battery was disconnected. The formula requires the following condition to be complied with. 365 - (A) [days] = (B) - (C) [days] For case 2: If the on-board electrical system battery (12 V/48 V) was not disconnected and the remaining time shown in the customer or workshop menu on the instrument cluster (days until the next service) is implausible in terms of the date of the vehicle handover or the last performed and confirmed service A/B, or the condition in the formula was not met, the service can still be performed and confirmed. For vehicles arriving more than 90 days after the service due date, the DSB service history can only be corrected by re-entering "Vehicle regularly serviced." A software fix for the EIS (electronic ignition lock) is currently in planning. The objective is to have a remedy available for 2026. Until the remedy is available, it is advisable to inform the customer that the next service is due again after 365 days at the latest.
LI54.10-P-0800532026-06-17. Service bulletin. ELECTRICAL SYSTEM. Complaint Discharge of 12 V battery in the event of a longer non-operational time - model series 232 and model series 192 Cause Increased quiescent current Remedy 1. Conduct quiescent current measurement. DO NOT USE A DVOM IN LINE - this will blow the fuse in your meter. Use an amp clamp with either a DVOM or XENTRY Scope and wait until the vehicle has gone to sleep (usually takes 6-10 minutes). Once the vehicle is asleep, observe the quiescent current for 10-15 minutes and note down the values. A stable quiescent current should be less than 50 mA. Values higher than this figure are considered not OK (NOK) and require further analysis. 2. If the quiescent current is higher (> 50 to 100 mA): • Check whether software updates are available for relevant control units: Door control units (DMD (N69/1), DMP (N69/2), DMRL (N69/3), DMRR (N69/4)), EIS (N73/3), PTCU (N127), OHCM (N70), GW (N73/3*1) • After installing the updates: measure the quiescent current again • If the quiescent current is < 50 mA, the vehicle is OK • If the quiescent current is between 50 and 100 mA, continue with step 5 • If the quiescent current is between 100 and 200 mA, continue with step 3 • If the quiescent current is between 200 mA and 1 A, continue with step 4 3. For no-load current values of 100 to 200 mA: • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Disconnect door separation points (A-pillar connection) when the vehicle is asleep, starting with the driver's side • Document the quiescent current value • If there is no change: Disconnect the door separation point on the front passenger side and note down the value again • If the quiescent current falls below 50 mA after the door separation point is opened, the respective outer door handle must be replaced • If the quiescent current drops below 50mA, the draw has been addressed and the vehicle can be released • If the quiescent current remains above 50mA after the relevant door handles have been successfully replaced, please create a TIPS case to the LV/HV inbox and retain the removed door handles for the time being • If the quiescent current does not change after the door separation point is opened, please carry out step 5 4. For quiescent current values between 200 mA and 1 A: • Important: Before pulling out F320 and F304, the tow-away protection and interior protection must be deactivated to prevent an alarm from triggering • Lock all doors and hood so that the control unit recognizes the door status as "closed" but the doors are open. • Wait until the vehicle has gone to sleep • Pull out the fuses one after the other, starting with F323 (PTCU CU/N127), and note down the quiescent current value • Perform the same test one at a time if the value is still high for each additional fuse: F119 (PTCU CU/N127), F324 (EIS CU/N73/3), F305 (EIS CU/N73/3), F320 (OCP CU/N70), F304 (OCP CU/N70) • If pulling out the fuse reduces the quiescent current to below 50 mA, replace the corresponding control unit. After replacing, please measure and assess the quiescent current again • If the quiescent current remains unchanged after the fuses listed above are pulled out, please carry out step 5 5. If the quiescent current remains above 50 mA after all controls have been implemented: • Create a TIPS case • Document all the completed steps and measurement results • Attach the XENTRY Scope trace of the draws that you have seen and identify where certain steps were taken. • Attach the latest N73 and N73/3*1 CUL's • If the quiescent current is higher than 1 A, the bus keep awake control unit should be identified via the EIS gateway
LI00.20-P-0807032026-06-16. Service bulletin. ELECTRICAL SYSTEM. Complaint Service code B1 displayed in the customer menu does not match the workshop code displayed in the workshop menu, e.g., 505 or 550A, which includes a service A. Cause The root cause is currently being investigated. Remedy To determine the cause, the instrument cluster control unit (N133/1) and powertrain control unit (N127) logs are required before confirming the service or correction using XENTRY Diagnosis. Please open a TIPS case to BCE inbox with the requested information in the attachments.
LI00.20-P-0776152026-06-16. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI00.20-P-0776152026-06-02. Service bulletin. ELECTRICAL SYSTEM. Complaint 1. "Perform vehicle handover" in the workshop menu to start the maintenance computer for service A/B cannot be carried out. 2. Service confirmation is not possible because "Perform vehicle handover" is displayed. This cannot be carried out. 3. The service display in the instrument cluster permanently displays 365 days (remaining time) and does not change. Cause Routine change in the software in N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)). Vehicle handover was not performed. Remedy For model series 290 AMG up to and including AEJ 22 and model series 167 up to and including AEJ 21/2, the following applies: Manually commission already-installed instrument cluster control unit N133/1 and then perform special procedure to re-initialize ASSYST data in N127 powertrain control unit. For model series 167 as of AEJ 22/1, 192 AMG, 206, 214, 232 AMG, 236, 254, 290 AMG as of AEJ 23, 294, 295, 296, 297 and 465, the following applies: Reinitialize ASSYST Plus under Adaptations – Teach-in processes – ASSYST PLUS in control unit N133/1 (instrument cluster) or A26/17 (MBUX multimedia system and instrument cluster (head unit)), and then perform the special procedure for reinitializing the ASSYST data in powertrain control unit N127.
LI54.10-P-0806022026-05-21. Service bulletin. ELECTRICAL SYSTEM. Complaint 48V battery (A66) part numbers A 000 982 78 24, A 000 982 57 30, A 000 982 88 31, A 000 982 50 32, A 000 982 87 32) may trigger a fault message ("48 V Service Required" with fault codes P0ADA91, P0ADE91, P0AA100, P0ADD00 or P0AA000) in the instrument cluster. This fault message may prevent the 48 V battery contactors from opening automatically if the 12 V power supply is interrupted. In this case, the 48 V on-board electrical system, including connected components, remain energized. Cause The contactors of the 48 V battery do not open, resulting in residual voltage (> 3V) even when the 12 V battery is disconnected. Remedy When working on the 48 V on-board electrical system or connected components, ensure the component being repaired is de-energized in the 48 V system after disconnecting the 12 V ground line. Use a DVOM and ensure that there is less than 3V across the 48V terminals. • If the voltage is less than 3V, the repair can be continued in accordance with the WIS documentation. • If the voltage is greater than 3V, disconnect the ground line from the 48 V on-board electrical system battery and secure from contacting any ground points of the vehicle before continuing the repair. Once the work has been completed, follow the procedure for clearing the 48 V battery fault message as specified.
LI54.65-P-0801322026-05-14. Service bulletin. BACK OVER PREVENTION: WARNINGS; ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.
LI54.71-P-0791042026-04-20. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy Do not replace parts. Please open a TIPS case to the Body/Chassis/Entertainment inbox but read the below carefully: • The vehicle must be exhibiting the concern as shown in the attachment videos. • The vehicle DOES NOT need to be at the dealer, nor does it need to be brought into the dealership. • If the geographic location is known, it is very important that it is provided. • Provide any pictures or videos, if available. A new software for the head unit is scheduled for tentative release in Q2 2026.
LI54.71-P-0791042026-04-10. Service bulletin. ELECTRICAL SYSTEM. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. NOTE: • Verify that the concern falls under one of the attachment videos. If not, then it is outside of the scope of this LI. • This also does not cover "Traffic Sign Inoperative" messages on the instrument cluster. Cause There are two identified reasons for this concern: 1. Country code information stored incorrectly at a particular geographic latitude range. 2. Incorrect reference data when the vehicle is started and a GPS signal is not immediately available. Remedy No TIPS case is necessary. Do not replace parts. A new software for the head unit is scheduled for tentative release in Q2 2026.
LI82.85-P-0803592026-03-19. Service bulletin. ELECTRICAL SYSTEM. Complaint Mercedes me connect services inoperative (me-Call, Remote Status, etc.). Mercedes me services - activation not possible Notes: - The event code "B16AC00 - The configuration of the SIM card is erroneous" is active and stored - The head unit shows no internet connection Cause The RAMSES module may be faulty. This fault profile can be recognized as follows: With XENTRY Diagnosis, enter the "ACTUAL values" menu of the RAMSES control unit and read out the values with position 175 and 727. ACTUAL values in the event of a fault: Type of mobile service (position 175): No reception Operating mode (position 727): Ready mode Remedy If B16AC00 is permanently active and saved and position 175 is no reception and position 727 is ready mode, it is highly likely that the communication module is faulty. In this case, an initial start up must be carried out. If the problem persists even after an initial start up, please create a TIPS case.
LI82.85-P-0787222026-03-17. Service bulletin. ELECTRICAL SYSTEM. Complaint The vehicle's position on the map is displayed far away from its actual position, e.g. the vehicle is displayed as being in the middle of the ocean. Note: No relevant DTC is displayed during the quick test. Cause The GNSS antenna is not correctly inserted at the GNSS connection (see picture in the attachment) in the head unit (A26/17). Remedy Insert the plug into the GNSS connection and ensure that the plug has engaged correctly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.