WenmarOpen by Wenmar Pro

Service bulletins for the 2025 Mercedes-Benz AMG GT

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

139 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Driver assistance are shown. Show all

Bulletins, newest first
LI54.65-P-0801322026-05-14. Service bulletin. BACK OVER PREVENTION: WARNINGS; ELECTRICAL SYSTEM; LANE DEPARTURE: BLIND SPOT DETECTION. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.
LI54.65-P-0801322026-01-31. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION: WARNINGS. Complaint 1. General Diagnostic Tips 2. One or More PARK Sensor Activations 3. Red Ring Around Vehicle 4. "Active Parking and Parking Assist Inoperative" on Instrument Cluster 5. Cameras 6. Other Park Topics Cause Various root causes Remedy See attached diagnostic guide.
LI46.10-P-0780122025-08-01. Service bulletin. LANE DEPARTURE: ASSIST; ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Proceed to replace the steering wheel. If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible -> Proceed to replace the steering wheel. In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).
LI46.10-P-0780122025-05-09. Service bulletin. FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; LANE DEPARTURE: ASSIST; STEERING. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness. Remedy In the event of a customer complaint and fault code in IDC control unit: U186B29 in IDC223 or fault code U0429E0, U042941, U042929, U042902, U0429E1 in IDC213 or fault code in HOSWD control unit: B1E7614 Test: Please perform the new SCN coding for HOSWD control unit (N179/1) (available since May 2025). Please flash the IDC (N62/4) software A223 902 75 37 (only applies to HOSWD223). Erase fault memory Remedy: Switch on ignition without touching the steering wheel. If after 10 seconds without touching the steering wheel, one of the two fault messages appears in the IC: Please check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). If there is visible damage -> replace steering wheel electronics or feed lines. If there is no visible damage -> Please create TIPS case! If no yellow message appears in the instrument cluster within 10 seconds: Please grab the steering wheel all the way round, including the 6 o'clock chrome molding, with both hands (see picture 1). If the fault is triggered by grabbing the steering wheel rim or pressing on the 6 o'clock clasp, check contacts and feed lines in the steering wheel by means of visual inspection for damage, crimped connections, loose connections, etc. (example in picture 2 and 3). Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). If there is visible damage -> replace steering wheel electronics or feed lines. If no fault is visible: Please open a TIPS case! In the event of a customer complaint and further fault code in HOSWD: B1E7713: Check ground connections (screw connections and cable to steering wheel rim); if necessary tighten screws/bolts and check for corrosion (Picture 4). B1F1F04: Check hand detection system control unit; if necessary swap with donor vehicle (ensure that the HW part numbers are identical).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.