Service bulletins for the 2023 Mazda CX-50
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
351 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Body and frame are shown. Show all
| SA-031-26 | 2026-05-05. Service bulletin. STRUCTURE:BODY; UNKNOWN OR OTHER. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the Bpillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory. |
|---|---|
| SA-021-26 | 2026-05-05. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure. |
| SA-008-26a | 2026-05-04. Service bulletin. STRUCTURE:BODY. During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. REPAIR PROCEDURE Check the rear bumper for an indentation. Repair bumper. |
| SA-008-26 | 2026-03-04. Service bulletin. STRUCTURE:BODY. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-041/25 10/31/25 and 09/10/25 During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. |
| SA-004-26 | 2026-02-03. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some customers may complain that a door beltline molding is loose, fell off, or is missing. |
| 09-006-26 | 2026-02-03. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE:BODY. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate. To eliminate this concern, the internal structure of the latch and surface treatment of the bolts have been modified. |
| 09-045-25 | 2026-01-03. Service bulletin. STRUCTURE:BODY. Some customers may experience that the fuel lid and charge lid do not lock or unlock during door lock/unlock operation. This is caused by: Improper dimensional accuracy of the lid actuator lock mechanism Incomplete control logic in the R-ESU software To eliminate this concern: The mold design of the lid actuator was modified. The control software of the R-ESU was revised. |
| 09-010-25b | 2025-12-04. Service bulletin. STRUCTURE:BODY. Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3. To eliminate this concern, the following changes have been implemented. CAUSE 1: The shape of the side cover and clips have been modified to reduce the movement causing the rattle noise CAUSE 2: Improvement of the assembly process CAUSE 3: Modification of dimensions of the moving parts |
| SA-041-25a | 2025-11-05. Service bulletin. STRUCTURE:BODY. During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. |
| SA-011-25a | 2025-11-05. Service bulletin. STRUCTURE:BODY. Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. |
| SA-041-25 | 2025-10-03. Service bulletin. STRUCTURE:BODY. During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. |
| SA-039/25 | 2025-09-05. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. If a structure's windows create enough of a curve, the concave glass can focus the sun's rays onto a small area and acting like magnifiying glass direct the sunbeams into a hot pinpoint of light. This magnifcation of the sun's rays can cause damage to vehicle trim (see examples). Additional information and exemplar images regarding this phenomenon can be found by performing a google search. |
| 09-010-25a | 2025-06-04. Service bulletin. STRUCTURE:BODY. Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3. To eliminate this concern, the following changes have been implemented. CAUSE 1: Addition of non-woven fabrics CAUSE 2: Improvement of the assembly process CAUSE 3: Modification of dimensions of the moving parts Customers having this concern should have their vehicle repaired using the following repair procedure. |
| SA-011-25 | 2025-03-05. Service bulletin. UNKNOWN OR OTHER; STRUCTURE:BODY. Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present. |
| 09-10-25 | 2025-03-04. Service bulletin. STRUCTURE:BODY. Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3.Looseness in the movable part inside the sunroof unit |
| SA-075-24 | 2024-11-04. Service bulletin. STRUCTURE:BODY. Some customers may complain that a door beltline molding is loose, fell off, or is missing. |
| 09-046-24 | 2024-11-03. Service bulletin. STRUCTURE:BODY. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier. If you encounter this concern during PDI, use a heat gun or an infrared drier to apply heat to the affected area to remove the stain(s). |
| SA-059-24 | 2024-09-04. Service bulletin. FUEL/PROPULSION SYSTEM; STRUCTURE:BODY. Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-019/21 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2021 Mazda3 and 2020-2021 CX-30 are present. |
| SA-058-24 | 2024-09-04. Service bulletin. STRUCTURE:BODY. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection. |
| SA-056-24 | 2024-09-04. Service bulletin. STRUCTURE:BODY. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. |
| 09-024-24a | 2024-07-05. Service bulletin. STRUCTURE:BODY. Some customers may experience the following concerns: The liftgate or the trunk lid will not unlock even when the vehicle is parked and the ignition is off. If the engine is running (POWER ON) or the ignition is turned to on (READY ON), it will unlock. The auto close operation of the power liftgate is not performed (The liftgate can be closed manually). To eliminate this concern, the control software of the DSC HU/CM (or the electronically controlled brake unit) has been modified. Customers |
| 09-031-24 | 2024-07-04. Service bulletin. STRUCTURE:BODY. Some customers may complain that the black felt padding on the A-pillar trim is visible. This is caused by the felt tape on the A-pillar trim not having enough adhesive. It may cause the felt to become detached and move to the visible area in the dash due to time passing or from heat. To eliminate this concern, the felt tape has been improved with more adhesive. |
| SA-036-24 | 2024-06-04. Other. STRUCTURE:BODY. Some customers may complain about color discrepancies (brightness differences) of the image displayed on the screen when using the 360°view monitor. As this phenomenon is not a system failure, do not make any repairs or replace any parts. Explain the cause of this occurrence to the customer as follows: The 360°view monitor is a system that provides a complete picture of the vehicle surroundings by combining the pictures captured by 4 separate cameras. These cameras are installed in the front, rear, right and left sides of the vehicle. Each camera has a color adjustment function (white balance) that operates independently from each other, which can result in color discrepancy when the combined picture is displayed on the screen. This is especially true when one of the cameras captures more green objects than the remaining cameras. |
| SA-001-24a | 2024-03-05. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY; STRUCTURE. Some customers may report a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. |
| SA-001-24 | 2024-02-02. Service bulletin. STRUCTURE; VISIBILITY:SUN/MOON ROOF ASSEMBLY. Some customers may report a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.