Service bulletin 09-010-25a

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	11019094
Published by NHTSA	2025-06-04
Manufacturer's number	09-010-25a
Manufacturer's date	2025-05-29
NHTSA component	STRUCTURE:BODY
Manufacturer's system	Sunroof

NHTSA's summary

Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3. To eliminate this concern, the following changes have been implemented. CAUSE 1: Addition of non-woven fabrics CAUSE 2: Improvement of the assembly process CAUSE 3: Modification of dimensions of the moving parts Customers having this concern should have their vehicle repaired using the following repair procedure.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Body and frame

Vehicles listed
MAZDA CX-50	2023, 2024
MAZDA CX-50 HYBRID	2025 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-031-26	2026-05-05. Service bulletin. DESCRIPTION Some vehicles may require the replacement of a damaged VIN plate or vehicle certification label. To obtain a replacement VIN plate (bulkhead-mounted and visible through the lower-left area of the windshield), contact DAG (Dealer Assistance Group) using VIN Plate Request Form available on One Mazda. To obtain a replacement vehicle certification label (located on the B􀀀pillar or front door), contact your assigned DSM (District Service Manager) to place the order. If DSM contact information is not available, refer to the Dealer & Field Contact Directory.
SA-021-26	2026-05-05. Service bulletin. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure.
SA-008-26a	2026-05-04. Service bulletin. During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern. REPAIR PROCEDURE Check the rear bumper for an indentation. Repair bumper.
SA-008-26	2026-03-04. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-041/25 10/31/25 and 09/10/25 During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern.
SA-004-26	2026-02-03. Service bulletin. Some customers may complain that a door beltline molding is loose, fell off, or is missing.
09-006-26	2026-02-03. Service bulletin. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate. To eliminate this concern, the internal structure of the latch and surface treatment of the bolts have been modified.
09-045-25	2026-01-03. Service bulletin. Some customers may experience that the fuel lid and charge lid do not lock or unlock during door lock/unlock operation. This is caused by: Improper dimensional accuracy of the lid actuator lock mechanism Incomplete control logic in the R-ESU software To eliminate this concern: The mold design of the lid actuator was modified. The control software of the R-ESU was revised.
09-010-25b	2025-12-04. Service bulletin. Some customers may complain about a rattle from the sunroof (panorama roof) area. Make sure to read the complete repair procedure before attempting any repairs as the sunroof may have rattles from more than one location. The rattle noise may be caused by: Looseness in the side cover fitting part 1. Looseness in the cross brace cover clip 2. Looseness in the movable part inside the sunroof unit 3. To eliminate this concern, the following changes have been implemented. CAUSE 1: The shape of the side cover and clips have been modified to reduce the movement causing the rattle noise CAUSE 2: Improvement of the assembly process CAUSE 3: Modification of dimensions of the moving parts
SA-041-25a	2025-11-05. Service bulletin. During PDI, an indentation in the rear bumper may be noticed, or in some cases, the customer may return after delivery to report the indentation. Follow the steps below to repair the concern.
SA-011-25a	2025-11-05. Service bulletin. Some customers will report that their fuel door (AKA, fuel filler door, fuel lid, and fuel-filler lid) was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-007/25 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2025 Mazda3 and 2020-2025 CX-30 are present.