WenmarOpen by Wenmar Pro

Service bulletins for the 2016 Mazda CX-5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

705 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
04-003-19-3589a2019-07-01. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS; WHEELS. Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold). NOTE: For vehicles equipped with the Smart City Brake System (SCBS), the master warning light also comes ON with the message "SCBS Inspection Required" in the display. The symptoms may occur when the following conditions are met: After starting the engine, the vehicle is driven backwards while the steering wheel is turned to the left or to the right or going forward over a bump while turning the steering wheel. The vehicle is then driven forward and begins accelerating while the steering wheel is still turned. To eliminate this concern, the DSC HU/CM software has been changed.
06-002-19-3585a2019-05-31. Service bulletin. STEERING; STEERING: STEERING WHEEL/HANDLE BAR. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
SA-006-19a2019-05-30. Service bulletin. BACK OVER PREVENTION; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
05-004-19-34662019-05-30. Service bulletin. POWER TRAIN. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil pressure switch No. 4 (oil pressure switch B) stuck on P0780:00 - Gear shifting malfunction P1738:00 - Automatic transaxle internal malfunction This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been implemented to reduce contamination and improve the DTC diagnostic logic. NOTE: If the vehicle also has a delayed engagement concern, this TSB is not applicable. Refer to the instructions on MGSS (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [FW6A-EL/FW6AX-EL]) or (SLOW ENGAGING AFTER OPERATING SELECTOR LEVER FROM N TO D POSITION [EW6A-EL/EW6AX-EL]) for proper diagnosis and repair procedure.
01-010-19-3582a2019-05-30. Service bulletin. ENGINE AND ENGINE COOLING. Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.
04-003-19-35892019-05-03. Service bulletin. WHEELS; TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold). NOTE: For vehicles equipped with the Smart City Brake System (SCBS), the master warning light also comes ON with the message "SCBS Inspection Required" in the display. The symptoms may occur when the following conditions are met: After starting the engine, the vehicle is driven backwards while the steering wheel is turned to the left or to the right or going forward over a bump while turning the steering wheel. The vehicle is then driven forward and begins accelerating while the steering wheel is still turned. To eliminate this concern, the DSC HU/CM software has been changed.
SA-016-192019-04-25. Service bulletin. WHEELS; SUSPENSION:FRONT:WHEEL BEARING. There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
SA-013-192019-04-25. Service bulletin. EQUIPMENT. MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the resetting tool.
SA-001-19b2019-04-25. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. APPLE CARPLAY™ / ANDROID AUTO™ FREQUENTLY ASKED QUESTIONS (FAQ)
01-008-19-3568a2019-04-25. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some customer using “Flexible” setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
SA-001-19a2019-03-29. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. APPLE CARPLAY™ / ANDROID AUTO™ FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers.
09-015-19-35782019-03-29. Service bulletin. STRUCTURE; STRUCTURE:BODY:DOOR. Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.
05-002-19-35762019-03-29. Service bulletin. POWER TRAIN; POWER TRAIN:AXLE ASSEMBLY. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: •Depends on the vehicle’s speed only (the more speed, the more noise)•Occurs with all types of driving (acceleration, deceleration, steady speed)•Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration of the transaxle case. A modification has now been implemented on automatic transaxles with the following serial numbers: •7TN0820364 and higher (CX-3) / 8TN1090104 and higher (except CX-3) •8TR1008883 and higher •8TD1003276 and higher •8T50331192 and higher (CX-3) / 8T50329705 and higher (except CX-3).
03-001-19-3505b2019-03-29. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT. Some vehicles may exhibit a squeak noise from the right front driveshaft at the automatic transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.
01-010-19-35822019-03-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem.This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate this concern, the PCM software has been modified.
00-003-19-35832019-03-21. Service bulletin. FUEL SYSTEM, DIESEL:STORAGE:TANK ASSEMBLY; FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING; EQUIPMENT. In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
09-003-19-3555a2019-03-20. Service bulletin. EXTERIOR LIGHTING; EXTERIOR LIGHTING:HEADLIGHTS; EXTERIOR LIGHTING:TAIL LIGHTS. Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between the inside and the outside of the light housing. It is normal for very small water drops to appear in certain locations on the light units where the air is stagnant (condensation), making the lens look whitish (fog). This happens mostly in the corners and narrow spaces, and will typically clear during warmer ambient temperatures, or when the lights have been on for some time.
SA-006-192019-03-11. Service bulletin. ELECTRICAL SYSTEM. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
09-010-19-35772019-03-11. Service bulletin. ELECTRICAL SYSTEM. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
06-001-19-35752019-03-11. Service bulletin. STEERING. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position.The noise is caused when the edge (A) of the inner ball joint (B) gets stuck with the steering gear housing(C). To eliminate the noise, a spacer (A) has been installed between the inner ball joint (B) and the steering gear housing (C) (both sides) to prevent direct contact.
05-001-19-35382019-03-11. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION. When pressing the START/STOP button in very cold weather, the ignition may not turn off on some vehicles equipped with a lock release button (1) on the selector lever knob. Although the selector lever is in the "P" position and the engine shuts off normally, the ignition may stay on (in accessory mode). NOTE: This TSB only applies if the selector lever knob is BHN2-46-030* or BHN4-46-030* with the lock release button. If not, this TSB does not apply. This may be caused by the lock release button in the selector lever knob sticking in the pressed position. An improper production process is causing an internal part to expand with moisture and interfere with other parts. To eliminate this concern, the production process has been modified.
01-008-19-35682019-03-11. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some customer using "Flexible" setting for Oil Change in the maintenance monitor may notice that the oil change due notification will not work due to improper control logic of the PCM. The PCM clears the TRAVELED DISTANCE at the wrong time while the ELAPSED DAYS and the DETERIORATION DETERMINATION work as designed. To correct this issue, the control logic of the PCM has been changed.
SSPA6a2019-03-11. Service bulletin. AIR BAGS. Special Service Program (SSP) A6 - 2016 CX-5 Passenger Frontal Air Bag Concern - MDRT TOOL RETURN - UPDATE ON RETURN PROCEDURE. On July 12th, 2018, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 7 months to improve the low completion rate for campaign SSPA6. As previously advised the MDRT Tool loaner software is expiring at the end of February 2019. New MDRT tools are being prepared to reprogram the Airbag Control Module for those vehicles that remain unrepaired. These tools will replace the MDRT currently at your dealership for this SSP. Action required: All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by February 28, 2019. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge.
SSPA62019-03-11. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. Special Service Program (SSP) A6 - 2016 CX-5 Passenger Frontal Air Bag Concern - MDRT TOOL RETURN. On July 12th, 2018, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 7 months to improve the low completion rate for campaign SSPA6. As previously advised the MDRT Tool loaner software is expiring at the end of February 2019. New MDRT tools are being prepared to reprogram the Airbag Control Module for those vehicles that remain unrepaired. These tools will replace the MDRT currently at your dealership for this SSP. Action required: All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by February 28, 2019. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge.
MT-012-182019-03-04. Service bulletin. STRUCTURE:BODY; STEERING. If a vehicle has body vibration or steering wheel shimmy while driving and the root cause is determined to be tire balance, re-balance the tires using a Hunter GSP9700 or equivalent balance machine. If your dealer does not have a GSP9700 or equivalent balance machine, sublet the vehicle out for repair. To find the location of a GSP9700 near your dealer, visit Hunter?s web site at www.gsp9700.com and click on ?Locate a GSP9700 Road Force Balancer.?

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.