Service bulletin SSPA6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10154429 |
| Published by NHTSA | 2019-03-11 |
| Manufacturer's number | SSPA6 |
| Manufacturer's date | 2019-02-05 |
| NHTSA component | ELECTRICAL SYSTEM; AIR BAGS |
NHTSA's summary
Special Service Program (SSP) A6 - 2016 CX-5 Passenger Frontal Air Bag Concern - MDRT TOOL RETURN. On July 12th, 2018, Mazda Technical Services sent out an email extending the Mazda Diagnostic Reprogramming Tool (MDRT) service loaner program for Special Service Program (SSPA6) for an additional 7 months to improve the low completion rate for campaign SSPA6. As previously advised the MDRT Tool loaner software is expiring at the end of February 2019. New MDRT tools are being prepared to reprogram the Airbag Control Module for those vehicles that remain unrepaired. These tools will replace the MDRT currently at your dealership for this SSP. Action required: All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by February 28, 2019. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Air bags, Electrical system
| MAZDA CX-5 | 2016 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| SA-041-26a | 2026-10-03. Service bulletin. DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button |
|---|---|
| SA-041-26 | 2026-07-03. Service bulletin. This SA supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-061/25 12/17/25 DESCRIPTION If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the DLC-2 (battery discharge/DTC stored) 2. Devices plugged into the 12V outlet 3. GPS tracking device (engine no start/battery discharge) 4. Dash cam (DTC stored) 5. Non-certified USB cable (Apple Carplay™/ Android Auto™ will not connect) 6. Over-sized wheels/tires (incorrect GPS location) 7. DTC C0023:14 8. Decorative trim and/or cover on the START/STOP ENGINE button Example 1: Some electrical devices connected to the DLC-2 connector by insurance or mobile phone companies may cause: Battery discharge. The device may disrupt the CAN system battery saver mode. • IDS/MMDS will not communicate with the vehicle due to poor DLC-2 connection. The aftermarket device may cause DLC-2 female terminals to spread open. |
| SA-021-26 | 2026-05-05. Service bulletin. This Service Alert supersedes the previously issued SAs and bulletin(s) listed below: The changes are noted below in red. SA-010/23 02/09/23 DESCRIPTION Some customers may experience one or more electrical malfunctions after a vehicle body repair. A newly painted fender stay (2) may be causing a poor front harness (1) ground connection. The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. NOTE: DO NOT paint ground point (3) attachment bolt (4) is seated. NEWLY INSTALLED FRONT FENDER STAY NOTE: CAUTION: If the bolt (4) contact area (3) is painted when the front fender stay (2) is newly replaced, it could cause a malfunction in the PCM. Before painting a newly replaced part, protect the bolt (4) contact area (3) with masking tape (5) as shown in the figure. |
| SA-061-25 | 2026-01-04. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. |
| SA-044-25 | 2025-11-05. Service bulletin. For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage. |
| SSPA6 FCa | 2025-05-05. Service campaign. Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2016 CX-5 vehicles built from November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSA’s new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool. |
| SSPA6 Repair | 2025-04-02. Service campaign. Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2016 CX-5 vehicles built from November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSA’s new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool. |
| SSPA6 FC | 2025-04-02. Service campaign. Mazda Motor Corporation has decided to conduct a Special Service Program (SSP) on certain 2016 CX-5 vehicles built from November 1, 2014 through May 13, 2016. If you are a recipient of this notice, your vehicle is included in Special Service Program (SSP) A6. What is the problem? Certain 2016 CX-5 vehicles were evaluated under NHTSA’s new frontal oblique crash test, and the evaluation revealed that the fabric of the passenger frontal air bag may be torn during deployment of the air bag. NHTSA performed a frontal oblique crash being evaluated for inclusion in the New Car Assessment Program (NCAP). The NCAP test being evaluated is not a requirement of the current vehicle safety regulations or NCAP ratings, but will be used for NCAP safety ratings for future model year vehicles. Even though 2016 CX-5 vehicles fully satisfy the current vehicle safety regulations, we are conducting the SSP to minimize any potential safety risk. Action required: As previously advised the MDRT Tool loaner software expired July 15, 2020. All dealers must return their MDRT SSPA6 Tool to Mazda with a Warranty Part Return Shipping label by August 21, 2020. Any MDRT SSPA6 Tool not returned to Mazda by that time will incur a $1,000.00 missing tool charge. New Mazda dealers that do not have this tool, please fill out the Dealer Recall Help form on MXConnect > Warranty to advise you do not have the tool. |
| SA-062-24 | 2024-09-04. Service bulletin. For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage. |
| SA-057-24 | 2024-09-04. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. |