WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Lincoln MKZ

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

226 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Engine are shown. Show all

Bulletins, newest first
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 475022018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some 2017-2018 Fusion, MKZ and C-Max vehicles with 2.0L Gas/Electric engine may exhibit an illuminated MIL with DTC P013A in the Powertrain Control Module(PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at exhaust connections. Inspect welds including CMS Boss, flex pipe and flanges. Inspect Catalyst Monitor Sensor(CMS) threads and crush washer to confirm sensor is fully seated in pipe boss. Do not use Vacutec smoke machine to diagnose sensor leaks. Applying soapy water solution to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI(do not exceed 5 PSI), will increase ability to identify and confirm leaks
SSM 474622018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. 2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
SSM 474462018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
TSB 18-22552018-09-24. Service bulletin. ENGINE. Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
18L022018-07-23. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
18M022018-07-23. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
SSM 470002018-06-11. Service bulletin. ENGINE; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE). Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 470002018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2013-2018 Escape/Fusion/MKZ vehicles equipped with 2.5L or 1.5L/2.0L/3.0L Ecoboost engine, 2015-2018 MKC/Edge/Explorer vehicles equipped with 2.0L/2.3L/2.7L EcoBoost engine, 2016-2018 MKX vehicles equipped with 2.7L Ecoboost engine, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost, and AWD may exhibit a fluid leak from the PTU intermediate shaft seal. Replacement of the intermediate shaft seal seal does not require removal of the PTU and does not require the use of the cover seal and bolt kit (CV6Z-7275-K) to perform the repair. Refer to the Workshop Manual (WSM), Section 308-07.
SSM 472652018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engines may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan by performing the published Workshop Manual (WSM) service procedures. After removing the oil pan, it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV, clean the engine sealing surface with only Motorcraftù Metal Brake Parts Cleaner then wipe with Motorcraftù Metal Surface Prep Wipes, and allow to air dry as directed in WSM, Section 303-00, RTV Sealing Surface Cleaning and Preparation. If possible, after the new oil pan is installed, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Ford is investigating this concern. Monitor OASIS for future updates.
SSM 472042018-05-21. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Fusion/MKZ/MKC/Escape/Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a runs rough condition with DTCs P0300, P0301, P0302, P0303, P0304 and/or P0316. This may be due to coolant intrusion due to corrosion on the engine block. To diagnose this concern, with the engine at normal operating temperature, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If the coolant pressure drops 27.57 kPa (4psi), remove the spark plugs and inspect for coolant in the cylinders. If coolant is found in any of the cylinders, replace the engine long block assembly. Follow normal prior approval process for your Dealership. However, follow the diagnostic repair procedure in this article to determine correct repair. For claiming, use causal part 6006 and applicable labor operations in Section 6 of the SLTS Manual.
17-22352018-01-29. Service bulletin. ENGINE. Some 2016-2017 Edge/MKX, 2017 Continental, and 2017 Fusion/MKZ vehicles equipped with a 2.7L or 3.0L gasoline turbocharged direct injection (GTDI) engine and built on 1-Apr-2016 and through 1-Jan-2017 may exhibit white or blue smoke from the exhaust, rough idle in neutral or park at normal operating temperature or after a hot restart. The vehicle may also exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316, P0524 and/or P06DD with excessive oil consumption. Oil consumption may be 1 Liter (1 quart) in less than 4,800 km (3,000 miles). Follow the Service Procedure steps to correct the condition.
SSM 468162017-10-21. Service bulletin. ENGINE. 2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along with a laser etched crankshaft timing sprocket. Related WSM procedure information is in the process of being updated.
SSM 466872017-08-25. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Some 2017 Continental/MKZ vehicles equipped with 3.0L engine and all-wheel drive (AWD), built on or before 12-May-2017 may exhibit an all-wheel drive malfunction warning message/wrench light along with DTC U2008 that occurs when using a conveyor type car wash. Connect the Ford Integrated Diagnostic System (IDS) or equivalent and check the AWD module for DTCs. If DTC U2008 is stored, then reprogram the AWD module to the latest level using IDS release 106.02 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 7E453 and applicable labor operations in section 10 of the service labor time standards (SLTS) manual.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
SSM 460762017-08-01. Service bulletin. EQUIPMENT; ENGINE. Some 2016 Model Year Fusion, MKZ and C-MAX Hybrid Electric Vehicles(HEV) vehicles equipped with 2.0L DOHC Gas/Electric engines may exhibit MIL On with Diagnostic Trouble Code P0137(O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2) in Powertrain Control Module(PCM) memory and U3003 (Battery Voltage) in Battery Energy Control Module(BECM) memory due to low battery voltage. Perform Battery diagnostic tests referenced in Workshop Manual Section 414-01 Battery, Mounting and Cables-Diagnosis and Testing. After repairs for low voltage concern are repaired, clear Diagnostic Trouble Codes. If DTC P0137 and U3003 do not repeat return vehicle to the Customer. If DTC P0137 repeats perform Powertrain Control and Emissions Manual(PCED) diagnostic DW. Engineering is currently investigating this concern.
SSM 460482017-08-01. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may have DTCs U3000:04, B108E:12 and/or U1A00:87 present in the APIM. If these DTCs are present and no other symptoms are reported by the customer, then clear the DTCs and retest. If the DTC(s) do not return then no further repairs should be attempted. If one or more DTCs return as current faults and/or the customer reports other symptoms, then refer to Workshop Manual, Section 415-00 for further diagnostics. The SYNC version can be confirmed via OASIS.
TSB 16-01202017-08-01. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Some 2017 Fusion and MKZ vehicles equipped with a 2.0L Gasoline Turbocharged Direct Injection (GTDI) engine and built on or before 31Aug2016 may exhibit an illuminated MIL with DTC P04DB (crankcase ventilation system disconnected) in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.
TSB 16-01192017-08-01. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Some 2017 Fusion and MKZ vehicles equipped with a 2.0L Gasoline Turbocharged Direct Injection (GTDI) engine built on or before 31-Aug-2016 may exhibit a lack of power drivability concern with an illuminated malfunction indicator lamp (MIL) and DTC P0234 stored in powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.
TSB 16-01132017-08-01. Service bulletin. ENGINE. Some 2017 MKZ vehicles equipped with 3.0L engine and built on or before 8-Aug-2016 may exhibit a rough idle in neutral or park at normal operating temperature or after a hot restart with or without diagnostic trouble codes (DTCs) P0300, P0301, P0302, P0303, P0304, P0305, P0306 and/or P0316. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 102.01 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
TSB 17-20722017-08-01. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 C-MAX/Fusion Hybrid/Energi and MKZ Hybrid vehicles may exhibit an illuminated MIL with DTC P0071 stored in the powertrain control module (PCM). This DTC can be set after the vehicle is stored inside a warm location for several hours and then driven on a cold day. Under these conditions the PCM may see a temperature sensor concern when it first compares the ambient air temperature (AAT) sensor to other engine temperature sensors and set the DTC. Reprogram the PCM to the latest calibration using Integrated Diagnostic System (IDS) release 104.04 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates. Calibration files may also be obtained at www.motorcraftservice.com.
SSM 461722017-03-20. Service bulletin. ENGINE. SOME 2015-2017 F-150, 2016 MKX, 2015 EDGE, 2017 FUSION, MKZ AND CONTINENTAL VEHICLES EQUIPPED WITH A 2.7L/3.0L ENGINE MAY APPEAR TO HAVE LOW ENGINE OIL LEVEL IF THE PROPER PROCEDURES ARE NOT FOLLOWED. REFER TO THE OWNERS GUIDE, MAINTENANCE, ENGINE OIL CHECK SECTION. WHEN CHECKING THE ENGINE OIL LEVEL AFTER SHUTTING OFF THE ENGINE WAIT AT LEAST 15 MINUTES PRIOR TO CHECKING IN ORDER TO ALLOW THE OIL TO DRAIN BACK TO THE OIL PAN. THE ENGINE OIL LEVEL CAN BE CHECKED IMMEDIATELY IF THE ENGINE HAS NOT BEEN STARTED. WHEN CHANGING THE ENGINE OIL THE ENGINE NEEDS TO BE AT NORMAL OPERATING TEMPERATURE AND THE OIL FILTER REMOVED BEFORE DRAINING THE OIL. ALLOW THE OIL PAN TO DRAIN COMPLETELY FOR UP TO 5 MINUTES. CHECK OIL LEVEL AFTER FILLING BY FOLLOWING THE OIL LEVEL CHECK PROCEDURE.
SSM 464102017-03-20. Service bulletin. ENGINE; EQUIPMENT:APPLIANCE:AIR CONDITIONER. SOME 2017 FUSION HEV/PHEV, C-MAX HEV/PHEV, AND MKZ HEV VEHICLES MAY EXHIBIT AN ILLUMINATED MIL WITH DTC P0071 AND/OR DEGRADED HVAC PERFORMANCE IN AUTOMATIC MODE ONLY WITH AN AMBIENT TEMPERATURE READING OF 50 DEGREES F DISPLAYED IN THE MESSAGE CENTER. IF AFTER PERFORMING NORMAL PINPOINT TEST DIAGNOSIS, A COMPONENT FAILURE IS NOT IDENTIFIED, DO NOT CONTINUE WITH FURTHER DIAGNOSIS OR PART REPLACEMENT. HAVING THE VEHICLE PARKED AND STARTED IN A WARM ENCLOSED AREA BEFORE BEING DRIVEN INTO COLD TEMPERATURES CAN INADVERTENTLY CAUSE THESE SYMPTOMS AND DTC. THE HVAC AND MESSAGE CENTER FUNCTIONS WILL RETURN TO NORMAL AFTER THE VEHICLE IS SHUT DOWN AND RESTARTED. CLEAR THE DTC USING THE FORD INTEGRATED DIAGNOSTIC TOOL (IDS) OR EQUIVALENT. ENGINEERING IS INVESTIGATING. MONITOR OASIS FOR UPDATES.
SSM 463642017-03-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. SOME 2017 MKZ/CONTINENTAL/FUSION VEHICLES EQUIPPED WITH THE 2.7L/3.0L ENGINE AND BUILT ON OR BEFORE 6-OCT-2016 MAY EXHIBIT A ROUGH IDLE IN NEUTRAL OR PARK AT NORMAL OPERATING TEMPERATURE OR AFTER A HOT RESTART, WHITE OR BLUE SMOKE FROM THE EXHAUST, EXCESSIVE OIL CONSUMPTION AND/OR AN ILLUMINATED MALFUNCTION INDICATOR LAMP (MIL) WITH DIAGNOSTIC TROUBLE CODES (DTCS) P0300, P0301, P0302, P0303, P0304, P0305, P0306 AND/OR P0316. SUSPECT THE CYLINDER HEADS AS THE CAUSE FOR THIS ISSUE. IF THE VEHICLE ALSO EXHIBITS P0524 AND/OR P06DD SUSPECT THE LONG BLOCK AS THE CAUSE FOR THIS ISSUE.
SSM 463412017-03-15. Service bulletin. ENGINE. WHEN SERVICING A 2.7L OR 3.0L ECOBOOST ENGINE, IF THE CRANKSHAFT PULLEY IS REMOVED, CORRECT REASSEMBLY IS CRITICAL TO PREVENT POTENTIAL ENGINE FAILURE. THIS INCLUDES INSTALLING A NEW CRANKSHAFT PULLEY BOLT AND ACCURATELY PERFORMING EACH STAGE OF THE CRANKSHAFT PULLEY BOLT TORQUE SEQUENCE. CRANKSHAFT PULLEY RELATED WORKSHOP MANUAL (WSM) PROCEDURE AND RECOMMENDED TOOL (OTC 4754 OR EQUIVALENT) INFORMATION HAVE BEEN UPDATED. REFER TO THE APPLICABLE WSM, SECTION 303-01, FOR ADDITIONAL INFORMATION.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.