WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Infiniti QX70

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

110 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB140562021-05-10. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
ITB140552021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
ITB140442021-05-10. Service bulletin. SERVICE BRAKES, HYDRAULIC. IF YOU CONFIRM: The rear brakes squeak when braking while the brakes are at normal operating temperature AND the applied vehicle is equipped with single piston rear brake calipers. ACTION: Replace the hardware on both rear brake calipers with the kit listed in PARTS INFORMATION in this bulletin. NOTE: Machining of the rotors is not necessary. Refer to the Electronic Service Manual (ESM), section BR-Brake System, for removal and installation. See this bulletin for further detail.
ITB10029A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
ITB140202021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING; EQUIPMENT. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
ITB140132021-05-10. Service bulletin. SEATS:MID/REAR ASSEMBLY; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. SERVICE INFORMATION The applied models can be equipped with a "factory installed" 2nd Row DVD system, or have an "accessory installed" 2nd Row DVD system (Figure 1). Before beginning diagnostics, confirm which type of 2nd Row DVD system is installed. This bulletin and the information on pages 2 and 3 applies only to the accessory installed 2nd Row DVD system. If you confirm a customer?s concern for the accessory installed 2nd Row DVD system, please follow the correct procedure for accessory part diagnosis and warranty on pages 2 and 3. Please see this bulletin for further details.
ITB140142021-05-10. Service bulletin. POWER TRAIN; STEERING. SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.
ITB13056A2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). IF YOU CONFIRM: The MIL is ON and one or both of the following DTCs are found stored in the ECM: - P0139 (heated oxygen sensor 2 (B1) circuit slow response) - P0159 (heated oxygen sensor 2 (B2) circuit slow response) ACTION: 1. Confirm this bulletin applies. - Compare the vehicle's current ECM part number to those listed in Table A (see page 4). 2. If the ECM part number does not match one listed in Table A, this bulletin does not apply. Go back to ASIST for further diagnostic and repair information. 3. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
ITB08024C2021-05-10. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
ITB140022021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
ITB07047D2021-05-10. Service bulletin. STRUCTURE. SERVICE INFORMATION Scratch Shield is a scratch-resistant clear coat which "heals" by itself when the vehicle gets a small scratch in the clear coat. If the scratch reaches the color base coat, however, it will not "heal". Scratch Shield was implemented for the first time in the U.S. with the 2008 EX35. NOTE: Scratch Shield is applied to body panels and fasicas only. Scratch Shield Label Vehicles equipped with Scratch Shield have a label (see Figure 1) which is typically located underneath the hood. Vehicles that DO NOT have the Scratch Shield label shown in Figure 1 are not equipped with Scratch Shield. See this bulletin for further detail.
ITB92069D2021-05-10. Service bulletin. EQUIPMENT; WHEELS. Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
ITB00024F2021-05-10. Service bulletin. STEERING; SUSPENSION; SERVICE BRAKES. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
ITB04038A2021-05-10. Service bulletin. SERVICE BRAKES; STEERING; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
ITB98011F2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
ITB17-015B2021-05-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB19-024A2021-04-13. Service bulletin. ELECTRICAL SYSTEM. DTC B00A0-00 STORED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-005A2021-04-08. Service bulletin. ELECTRICAL SYSTEM. BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
ITB16-006A2021-04-08. Service bulletin. ELECTRICAL SYSTEM. INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB12-041D2021-04-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. SIRIUSXM SATELLITE RADIO / WEATHER / TRAFFIC / TRAVEL LINK ACTIVATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
ITB11-003F2021-04-08. Service bulletin. ELECTRICAL SYSTEM. NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-017E2021-04-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. AV CONTROL UNIT REPLACEMENT REQUIRES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB20-023a2021-03-06. Service bulletin. ELECTRICAL SYSTEM; FORWARD COLLISION AVOIDANCE; EQUIPMENT. LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-024a2021-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). 2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB20-0232020-10-08. Service bulletin. ELECTRICAL SYSTEM; LANE DEPARTURE. LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. • For all other models, consult the Electronic Service Manual (ESM). The following CONSULT-III plus (C-III plus) figures and steps are only provided to indicate where the VEHICLE REFERENCE VALUE from Table A is to be entered. The entire camera aiming procedure must be followed to complete the aiming procedure. • Refer to the Electronic ESM section: CRUISE CONTROL & DRIVER ASSISTANCE > DRIVER ASSISTANCE SYSTEM > DRIVER ASSISTANCE SYSTEM > BASIC INSPECTION > LANE CAMERA UNIT > CAMERA AIMING ADJUSTMENT. 1. Turn the ignition ON. 2. From the C-III plus home screen, select Diagnosis (One System).

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.