WenmarOpen by Wenmar Pro

Service bulletins for the 2010 Infiniti G37

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

131 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB09039C2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION The purpose of this bulletin is to give Infiniti dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail.
ITB160052021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION The Intelligent Keys used on the various Infiniti vehicles may not be interchangeable between models and years. See this bulletin for further detail.
ITB13007A2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulleitn for further details.
ITB13039A2021-05-10. Service bulletin. BACK OVER PREVENTION; WHEELS; SERVICE BRAKES; LANE DEPARTURE. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
ITB14028A2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT. SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair. Unnecessary repair or replacement of parts in connection with incorrectly diagnosed "leaks" can negatively impact customer satisfaction, be time consuming and costly, and if not performed correctly can lead to future repairs. See this bulletin for further detail.
ITB10017D2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL. SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
ITB150252021-05-10. Service bulletin. BACK OVER PREVENTION; EQUIPMENT; WHEELS; SERVICE BRAKES; STEERING. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer are capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
ITB150242021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail.
ITB14010B2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION All parts listed in this bulletin's table are currently on parts restriction. If any of these parts are needed for any reason, order the part(s) using the order form in this bulletin. See this bulletin for further detail.
ITB150192021-05-10. Service bulletin. STRUCTURE; ELECTRICAL SYSTEM. SERVICE INFORMATION The Body Control Module (BCM) for the Applied Vehicles in this bulletin is now shipped as a blank unit. As with previous BCM replacements, when a blank unit is installed, the configuration process must be performed. See this bulletin for further detail.
ITB99043G2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Infiniti vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle. The PGF protects the paint finish during vehicle handling, transportation and storage from harmful elements such as acid rain,iron particles, bird droppings, tree sap and other environmental contaminants. NOTE - Paint Guard Film CANNOT remain on the vehicle for more than six months after the vehicle's manufacture date. PGF must be removed at the end of six months. See this bulletin for further detail.
ITB13005B2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT; SERVICE BRAKES. IF YOU CONFIRM: The clutch pedal on an applied vehicle does not return to its normal (rested) position after being depressed to the floor OR the customer states the clutch pedal on an applied vehicle does not return to its normal (rested) position after being depressed to the floor AND there are no leaks in the clutch hydraulic system. ACTION: Flush (remove) ALL existing clutch hydraulic system fluid, and refill with GT-R R35 Special Brake Fluid (see PARTS INFORMATION). - Use the SERVICE PROCEDURE in this bulletin for proper flush and refill procedure. See this bulletin for further detail.
ITB00031D2021-05-10. Service bulletin. AIR BAGS; EQUIPMENT; BACK OVER PREVENTION. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Infiniti STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail.
ITB13002A2021-05-10. Service bulletin. EQUIPMENT. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the Key-Slot. For DTC B2190 diagnosis; first perform the Service Manual DTC Confirmation Procedure. See this bulletin for further detail.
ITB11003E2021-05-10. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). SERVICE INFORMATION Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.infinitinavigation.com and is mailed update disc(s) or SD card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
ITB140562021-05-10. Service bulletin. ENGINE; ELECTRICAL SYSTEM. SERVICE INFORMATION Starting with 2010 Model Year, Infiniti vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM). If a DTC repair is performed and the DTC erased, a vehicle may fail an Emission Inspection and Maintenance test if the P-DTC is not also erased. See this bulletin for further detail.
ITB140552021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details.
ITB140302021-05-10. Service bulletin. STRUCTURE:BODY:ROOF AND PILLARS; ELECTRICAL SYSTEM. SERVICE INFORMATION If the battery becomes disconnected or discharged while the retractable hard top is in any position other than fully closed or fully retracted, the retractable hard top control may stop operating and the following DTCs will be stored: B1707 and B1708. Other retractable hard top related DTCs may also be found stored. To restore operation: (1) close the roof fully manually; (2) erase the DTC(s); and (3) perform hard top control unit initialization. This bulletin provides the procedures to restore retractable hard top control operation. See this bulletin for further detail.
ITB10029A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
ITB140232021-05-10. Service bulletin. EQUIPMENT; STRUCTURE:BODY:ROOF AND PILLARS. SERVICE INFORMATION If the hydraulic unit assembly (pump assembly) needs to be tested for any reason, the convertible top should not sink or drop further than 250 mm (9.84 inches) within one (1) minute or less when opened as shown in Figure 1. - If the convertible top sinks further than 250 mm (9.84 inches) within one (1) minute or less - the pump assembly needs to be replaced. - If the convertible top does not sink further than 250 mm (9.84 inches) within one (1) minute or less - the pump assembly is OK. NOTE: This instruction supersedes the previous 15 mm measurement threshold specified in SIR video # 165. CAUTION: The convertible top should only be partially opened for service and should not be left in this position as damage may result. See this bulletin for further detail.
ITB140202021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING; EQUIPMENT. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
ITB140142021-05-10. Service bulletin. POWER TRAIN; STEERING. SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.
ITB08024C2021-05-10. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
ITB140022021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); ENGINE. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
ITB09012F2021-05-10. Service bulletin. FUEL/PROPULSION SYSTEM; EQUIPMENT. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Infiniti vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >> EVAP SYSTEM CLOSE. NOTE: Use Essential Tool J-42909 or equivalent to pressurize the EVAP system. - With a "Smoke" leak detection machine. Refer to the machine's Operator's Manual for proper use. Make sure the customer is informed of the proper fuel filler cap installation.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.