WenmarOpen by Wenmar Pro

Service bulletins for the 2010 Infiniti G37

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

131 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
ITB12063C2021-05-10. Service bulletin. EQUIPMENT. IF YOU CONFIRM The customer reports that people on the other end of a phone call cannot hear them. Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Reprogram (reconfigure) the Multi AV. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.
ITB12062C2021-05-10. Service bulletin. EQUIPMENT. IF YOU CONFIRM The customer reports that people on the other end of a phone call cannot hear them. Customer report may include: Voice is choppy or cuts-out, voice sounds distant, voice sounds as if speaking through a tunnel, and/or voice sounds like it's under water. ACTION 1. Replace the TEL Adaptor Unit. 2. Replace the microphone and the map lamp finisher. See this bulletin for further detail.
ITB92069D2021-05-10. Service bulletin. EQUIPMENT; WHEELS. Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards. Infiniti Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Infiniti most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletin for further details.
ITB13006A2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
ITB11066E2021-05-10. Service bulletin. FUEL SYSTEM, GASOLINE. SERVICE INFORMATION Part order approval from TECH LINE is no longer required when replacing the Audio Visual (A/V) Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.
ITB130272021-05-10. Service bulletin. AIR BAGS; VEHICLE SPEED CONTROL; EQUIPMENT. SERVICE INFORMATION: If the BCM in an Applied Vehicle is replaced for any reason and not configured correctly, the following issue may occur - When the driver door is opened, the convertible top opens. When replacing a BCM, make sure to - Follow information in the appropriate Service Manual - Use CONSULT-III plus to perform configuration - Select the correct vehicle in CONSULT-III plus - Confirm the VIN is correct (matches the vehicle) in CONSULT-III plus - Select/install the correct configuration
ITB00024F2021-05-10. Service bulletin. STEERING; SUSPENSION; SERVICE BRAKES. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel, or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake issue based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific issue. See this bulletin for further details.
ITB04038A2021-05-10. Service bulletin. SERVICE BRAKES; STEERING; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see ITB00-024). See this bulletin for further detail.
ITB98011F2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details.
ITB130132021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
ITB130122021-05-10. Service bulletin. VEHICLE SPEED CONTROL; SEAT BELTS. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
ITB130082021-05-10. Service bulletin. WHEELS; EQUIPMENT; POWER TRAIN; BACK OVER PREVENTION. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. >Please see Service procedure for 2007-2011 Versa torque specifications on page 5. See this bulletin for further detail.
ITB99001A2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail.
ITB11014B2021-05-10. Service bulletin. STRUCTURE. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident vehicles. - Customers must not use discs that are warped, scratched, chipped, cracked, have abnormal edges or are otherwise damaged. Damaged or poor condition discs may cause the Player internal mechanism to jam or have optical pick-up errors. NOTE - Do not make a Warranty claim against a Player that will not play damaged or poor condition discs as described in this bulletin. See this bulletin for further detail.
ITB11046A2021-05-10. Service bulletin. BACK OVER PREVENTION:SOFTWARE. On the Applied Vehicles listed in this bulletin, the navigation, mobile phone, iPod®, and voice recognition functions may not be working as intended. To remedy this potential condition, Infiniti is conducting this voluntary service campaign to update the navigation software at no charge for parts or labor. In addition, as part of this navigation software update, a call waiting function will be added to the hands-free phone system. See this bulletin for further detail. Campaign ID # P1235
ITB12027D2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM If the customer reports or has previously reported: * Harsher than expected down shifts when coasting to a stop. * Hesitation/lag when accelerating after coasting. * Hesitation/lag or harsher than expected down shifts when coming to a stop and accelerating again (rolling stop). * Engine rev matching during moderate to heavy braking. ACTION 1. Referto step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM and TCM. See this bulletin for further detail.
ITB17-015B2021-05-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. NAVIGATION SYSTEM REBOOTS WHEN SXM TRAFFIC IS ENABLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB17-042D2021-04-13. Service bulletin. ENGINE AND ENGINE COOLING. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB16-006A2021-04-08. Service bulletin. ELECTRICAL SYSTEM. INFINITI; FRONT SONAR PARKING SENSOR SERVICE INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB11-003F2021-04-08. Service bulletin. ELECTRICAL SYSTEM. NAVIGATION MAP DATA UPDATE MATRIX This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB10-017E2021-04-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. AV CONTROL UNIT REPLACEMENT REQUIRES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB15-024a2021-01-09. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM). 2005-2015 INFINITI VEHICLES; ECM REPROGRAMMING SERVICE INFORMATION This bulletin is no longer active. Please discard previous versions of ITB15-024.
ITB17-042c2020-10-08. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; FUEL SYSTEM, GASOLINE; EQUIPMENT. INFINITI; DTC P0456 CAUSED BY EVAP LEAK AT VENT CONTROL VALVE O-RING This bulletin has been amended. See Amendment History on the last page. Please discard previous versions of this bulletin.
ITB15-019a2020-06-09. Service bulletin. ELECTRICAL SYSTEM. CONFIGURATION FOR BLANK REPLACEMENT BCM This bulletin is no longer applicable. Discard previous versions of ITB15-019.
ITB11-066f2020-06-09. Service bulletin. EQUIPMENT:ELECTRICAL. PREMIUM NAVI/AUDIO VISUAL CONTROL UNIT DIAGNOSIS AND ORDERING This bulletin is no longer applicable. Discard previous versions of ITB11-066.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.