Service bulletins for the 2014 GMC Yukon
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1641 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| PIP5230C | 2017-03-21. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION. |
|---|---|
| PIP5226A | 2017-03-21. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT FINDING NEEDLE BEARINGS DURING AN OIL CHANGE. TECHNICIAN WILL GAIN ACCESS TO THE ROLLER ROCKERS TO INSPECT THEM. ONLY REPLACE THE ROLLER ROCKER THAT IS MISSING NEEDLE BEARINGS. BE SURE TO CLEAN THE OIL DRAINS TO RETRIEVE THE NEEDLE BEARINGS. EACH ROLLER ROCKER HAS 66 BEARINGS. |
| PIP5130G | 2017-03-20. Service bulletin. FUEL SYSTEM, GASOLINE:FUEL INJECTION SYSTEM:FUEL RAIL; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN HOW TO DIAGNOSE AND REPAIR A VEHICLE WITH AN ENGINE THAT RUNS WITH AN INTERMITTENT CRANK NO START WITH A DIAGNOSTIC TROUBLE CODE P0011 OR P00C6 CURRENT OR HISTORY. THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE MAY BE STICKING OR BINDING CAUSING THE VALVE TIMING TO BE RETARDED. DEALER WILL NEED TO CYCLE THE CAMSHAFT POSITION ACTUATOR SOLENOID VALVE BY ENERGIZING IT USING GLOBAL DIAGNOSTIC SYSTEM 2. |
| PIP5104B | 2017-03-20. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A COLD ENGINE TICK NOISE FOR 50 SECONDS AT START UP. TECHNICIAN DETERMINES IF THE TICK NOISE IS POSSIBLY COMING FROM THE EXHAUST MANIFOLD, AS THIS NOISE COULD EASILY BE MISTAKEN FOR AN ENGINE TICK NOISE. IF YOUR SI DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN, THIS CONCERN SHOULD BE CONSIDERED A VEHICLE DESIGN CHARACTERISTIC OF THE ECM CALIBRATION AND NO ADDITIONAL REPAIRS SHOULD BE PERFORMED. |
| PIT5367 | 2017-03-16. Service bulletin. ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A BLANK DISPLAYS, FLASHING DISPLAYS, “ERROR OR UPDATE FAILED MESSAGES”, NAVIGATION MAP NOT LOADING, BLUETOOTH OR USB CONCERNS. TECHNICIAN SHOULD INSPECT THE USB/SD CARD PORT FOR A SD CARD OR A DEVICE PLUG INTO ANY OF THE USB PORTS. |
| PIT5365A | 2017-03-16. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW THE RADIO DISPLAY GETS THE AIR AMBIENT TEMPERATURE. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO4, IO5, OR IO6 THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO4, IO5, OR IO6 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. |
| PIT5365 | 2017-03-16. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW THE RADIO DISPLAY GETS THE AIR AMBIENT TEMPERATURE. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 1500 SERIES TRUCKS AND ALL SPORT UTILITY VEHICLE WITH REGULAR PRODUCTION OPTION CODE IO4, IO5, OR IO6 THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE ENGINE CONTROL MODULE AND THEN THE SIGNAL GOES ON HIGH SPEED LOCAL AREA NETWORK TO THE BODY CONTROL MODULE FROM THERE ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO3 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO. ON 2500/3500 SERIES TRUCKS PRODUCTION OPTION CODE IO4, IO5, OR IO6 RADIO THE AMBIENT AIR TEMPERATURE SENSOR IS HARD WIRED TO THE INSTRUMENT PANEL CLUSTER AND THEN THE SIGNAL GOES ON LOW SPEED LOCAL AREA NETWORK TO THE RADIO THEN MOST 50 BUS TO THE HUMAN MACHINE INTERFACE. |
| PIT5312A | 2017-03-16. Service bulletin. STEERING:COLUMN. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ON HOW TO DIAGNOSE AND REPAIR VEHICLES THAT MAY HAVE A GRIND, POP, SHUDDER OR BIND FEELING/NOISE IN THE STEERING COLUMN WHEN TURNING LEFT OR RIGHT. TECHNICIAN WILL INSPECT FOR THE LOWER COLUMN BEARING TO BE OUT OF POSITION AND THE UPPER INTERMEDIATE STEERING SHAFT TO LOWER COLUMN SHAFT BOLT AND NUT MAY BE CONTACTING THE INHIBITOR/SHIFTIER CABLE BRACKET. TECHNICIAN WILL REPLACE THE STEERING COLUMN FOR THIS CONCERN. |
| PIP5261 | 2017-03-16. Service bulletin. POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A HIGH PITCHED WHINE NOISE FROM THE VEHICLE NOTICED WHEN DRIVING IN AUTO 4WD. WHEN THE TRANSFER CASE CONTROL MODULE HAS TO MOVE THE TRANSFER CASE ACTUATOR MOTOR THE HIGHER CURRENT PASSING THROUGH THE MODULE CAUSES AN "ELECTRONIC BUZZ OR WHINE" WITHIN SOME OF THE CAPACITORS IN THE MODULE THAT CAN BE HEARD BY SOME OF OUR CUSTOMERS. THIS CAN ONLY BE HEARD WITH ALL ACCESSORIES AND HVAC OFF AND ONLY WHEN ACTUATOR MOVEMENT IS REQUIRED. THIS DOES NOT INDICATE A CONCERN WITH THE MODULE AND SHOULD NOT BE REPLACED TO ADDRESS THIS CONCERN. |
| PIP5259 | 2017-03-16. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN ABOUT VEHICLES THAT MAY HAVE A SERVICE ENGINE SOON WITH DIAGNOSTIC TROUBLE CODE P0300 AND AN ENGINE MISFIRE. TECHNICIAN WILL NEED TO INSPECT THE VALVE OPERATION, IF THE VALVE OR VALVES ARE NOT MOVING THE ACTIVE FUEL MANAGEMENT LIFTERS AND GUIDE ON THE BANK WITH THE CONCERN AND THE OIL PUMP AND OIL PAN ASSEMBLY SHOULD BE REPLACED. |
| PIP5230A | 2017-03-15. Service bulletin. EQUIPMENT. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN BEFORE REPLACING THE CRANKSHAFT TO REVIEW THE FOLLOWING. DEALER SHOULD COMPLETE THE SERVICE INFORMATION DIAGNOSTICS AND THE COST COMPARISON WORKSHEET FOR ASSEMBLY REPAIR VS REPLACEMENT. TECHNICIAN WILL USE THE LATEST VERSION OF 09-06-04-026G TO VERIFY THE ECM CALIBRATION IS NOT AN AFTERMARKET CALIBRATION. IF THE CUSTOMER PREFERS TO KEEP THE ORIGINAL NUMBERS MATCHING ENGINE PLEASE CALL TAC FOR REPAIR DIRECTION. |
| PIP4568R | 2017-03-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE; EQUIPMENT ADAPTIVE/MOBILITY. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THAT SOME VEHICLES MAY HAVE A SERVICE ENGINE SOON LAMP, ENGINE MISFIRE ON CYLINDER 1, 4, 6, OR 7 AND/OR TICK NOISE. TECHNICIAN WILL FOLLOW SERVICE INFORMATION DIAGNOSIS FIRST. IF SERVICE INFORMATION DIAGNOSIS DOES NOT ISOLATE THE CAUSE OF THIS CONCERN PERFORM A CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT SYSTEM COMPRESSION TEST IN SERVICE INFORMATION. IF THE RUNNING COMPRESSION OF THE MISFIRING CYLINDER STAYS BELOW 25 POUNDS PER SQUARE INCH REGARDLESS OF THE ACTIVE FUEL MANAGEMENT SOLENOID BEING COMMANDED ON OR OFF, AN ACTIVE FUEL MANAGEMENT LIFTER IS MECHANICALLY COLLAPSED/STUCK OR UNLOCKING AS SOON AS THE ENGINE IS STARTED. REPLACE ALL ACTIVE FUEL MANAGEMENT LIFTERS, AND ALL PLASTIC LIFTER GUIDES. ALSO PERFORM THE CYLINDER DEACTIVATION ACTIVE FUEL MANAGEMENT VALVE LIFTER OIL MANIFOLD DIAGNOSIS AND TESTING IN SERVICE INFORMATION. IF IT ISOLATES A CONCERN WITH THE VALVE LIFTER OIL MANIFOLD, REPLACE IT AND REEVALUATE THE CONCERN. THE ACTIVE FUEL MANAGEMENT LIFTERS CAN ALSO BE MONITORED FOR PROPER OPERATION BY CAREFULLY INSPECTING THE CYLINDER 1, 4, 6, AND 7 ROCKERS AND VALVES WHILE CRANKING OR BRIEFLY AND SAFELY RUNNING THE ENGINE WITH THE VALVE COVERS REMOVED. IF THE VALVE OR VALVES OF AN ACTIVE FUEL MANAGEMENT CYLINDER STOP MOVING WHILE DOING THIS TEST, THE ACTIVE FUEL MANAGEMENT LIFTER IS CAUSING THE CONCERN. FOR 2008-2009 FULL SIZE TRUCK/SUV OR A 2007-2009 CHEVROLET TAHOE WITH THE POLICE PACKAGE REPROGRAM THE ENGINE CONTROL MODULE. ON THE 2008-2009 PONTIAC G8, 2010-2011 CAMARO, AND 2007-2010 FULL SIZE TRUCKS WITH ACTIVE FUEL MANAGEMENT, ALSO DETERMINE IF THE ACTIVE FUEL MANAGEMENT PRESSURE RELIEF VALVE SHIELD THAT IS LISTED IN THE LATEST VERSION OF 10-06-01-008 HAS EVER BEEN INSTALLED. ON PASSENGER CARS WITH THE LS4 ENGINE, DETERMINE IF THE UPDATED OIL PAN GASKET THAT IS LISTED IN THE LATEST VERSION OF 11-06-01-007 HAS BEEN INSTALLED. |
| PIC3278F | 2017-03-14. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION PROVIDES INFORMATION TO THE TECHNICIAN THE STEPS NEEDED TO DIAGNOSE AND REPAIR THE VEHICLES THAT MAY HAVE UNWANTED OR PHANTOM PHONE CALLS. TECHNICIAN WILL NEED TO DETERMINE WHAT TYPE OF CALL THE CUSTOMER IS HAVING THAT IS UNWANTED. THE VEHICLE MAY RECEIVE AN INCOMING CALL JUST LIKE ANY OTHER PHONE. TYPICALLY THE CUSTOMER WILL HEAR THE PHONE RINGING IN THE VEHICLE. THIS SCENARIO ALSO INCLUDES INCOMING BLUETOOTH CALLS. ONE TYPE OF UNWANTED CALL CAN BE MADE IF THE KEY PAD IS FAULTY THE ONSTAR SYSTEM WILL TRY TO MAKE A BLUE BUTTON CALL FOR SHORTED VOLTAGE IN THE CIRCUITS. THE ONSTAR MODULE COULD HAVE AN INTERNAL FAULT AND PRODUCE A PHONE UNAVAILABLE AUDIO MESSAGE ALSO IT MAY HAVE A DIAGNOSTIC TROUBLE CODE U1500 OR B1000. REFER TO DIAGNOSTICS FOR THE DIAGNOSTIC TROUBLE CODE MAKING SURE TO FOLLOW ANY APPLICABLE BULLETINS OR PRELIMINARY INFORMATION SHEETS. A GREADYH OR GONSTAR READYH AUDIO MESSAGE HEARD WHILE DRIVING. IN SOME CASES IT HAS BEEN FOUND THAT THE CUSTOMER IS INADVERTENTLY PRESSING THE PUSH TO TALK BUTTON ON THE STEERING WHEEL CONTROLS. ON RARE OCCASIONS, OTHER ISSUES IN THE STEERING COLUMN OR STEERING WHEEL CONTROL SYSTEM MAY INDUCE THIS CONCERN. |
| 13364A | 2017-02-03. Service bulletin. AIR BAGS. 13364A - SERVICE UPDATE (REVISED EXPIRATION DATE). THIS BULLETIN PROVIDES A SERVICE PROCEDURE TO REPLACE THE PASSENGER SIDE FRONT AIR BAG ON CERTAIN VEHICLES. THESE VEHICLES MAY HAVE A CONDITION IN WHICH THE PASSENGER SIDE FRONT AIR BAG WILL NOT FUNCTION AS DESIGNED DUE TO AN ELECTRICAL CONNECTOR NOT BEING PROPERLY ENGAGED. THIS CONDITION MAY SET DIAGNOSTIC TROUBLE CODE (DTC) B0020 – PASSENGER FRONTAL DEPLOYMENT LOOP STAGE 2 RESISTANCE ABOVE THRESHOLD. IF THIS OCCURS, THE SENSING AND DIAGNOSTIC MODULE (SDM) WILL REQUEST THE INSTRUMENT CLUSTER TO ILLUMINATE THE AIR BAG MALFUNCTION INDICATOR LAMP. IF A CRASH EVENT OCCURS THE SDM WILL ATTEMPT AIR BAG DEPLOYMENT, BUT, IF THE MATING TERMINALS DO NOT MAKE CONTACT, THE SECONDARY STAGE OF THE PASSENGER SIDE FRONT AIR BAG WILL NOT DEPLOY, INCREASING THE RISK OF INJURY TO THE OCCUPANT. |
| 14515 MESSAGE | 2017-02-02. Service bulletin. STRUCTURE:BODY; ELECTRICAL SYSTEM; EQUIPMENT. 14515 - CUSTOMER SATISFACTION PROGRAM (STOP DELIVERY EXPANSION). APPROXIMATELY 8,776 ADDITIONAL VEHICLES HAVE BEEN ADDED TO THE RECALL POPULATION. THESE VEHICLES WERE SERVICED WITH A CHASSIS ELECTRONIC MODULE SUSPECTED OF CONTAINING INTERNAL CONTAMINATION. A VERY SMALL NUMBER OF OLDER MODEL VEHICLES ARE NOW INCLUDED AND IDENTIFIED IN IVH WHICH HAS BEEN UPDATED AS OF DECEMBER 2, 2014. ADDITIONALLY, THE IVH SYSTEM ISSUE THAT WAS COMMUNICATED HAS BEEN RECTIFIED AND ALL INVOLVED VEHICLES SHOULD NOW SHOW "INCOMPLETE – REMEDY NOT YET AVAILABLE". |
| 14281 | 2017-02-01. Service bulletin. SEATS; ELECTRICAL SYSTEM. 14281 - CUSTOMER SATISFACTION PROGRAM. CERTAIN 2014-2015 MODEL YEAR CHEVROLET SILVERADO, SUBURBAN, AND TAHOE MODEL VEHICLES AND 2014-2015 MODEL YEAR GMC SIERRA AND YUKON MODEL VEHICLES EQUIPPED WITH A DEALER INSTALLED REAR ENTERTAINMENT SYSTEM MAY HAVE A CONDITION IN WHICH THE REAR SEAT ENTERTAINMENT SYSTEM IN VEHICLES WAS RELEASED AS A DEALER ACCESSORY BEFORE FINAL GENERAL MOTORS VALIDATION APPROVAL. VALIDATION APPROVAL AT GM REQUIRES VERY RIGOROUS TESTING PRIOR TO RELEASE, WHICH, IN MANY CASES, GOES BEYOND WHAT IS REQUIRED TO COMPLY WITH GOVERNMENTAL SAFETY STANDARDS. THESE VEHICLES, AS EQUIPPED, STILL MEETS ALL FEDERAL MOTOR VEHICLE SAFETY STANDARDS. DEALERS ARE TO REMOVE AND REPLACE THE HINGED SCREEN STYLE REAR SEAT ENTERTAINMENT SYSTEM, WITH A REVISED SYSTEM FEATURING AN INTEGRAL SCREEN. |
| 10-08-110-001E | 2017-01-19. Service bulletin. EQUIPMENT. THIS INFORMATIONAL BULLETIN PROVIDES INFORMATION ON THE PROPER USE OF FLOOR MATS. |
| 15-08-44-001H | 2017-01-19. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. THIS INFORMATIONAL BULLETIN PROVODES INFORMATION ON THE GM OF CANADA ONSTAR CELLULAR COMMUNICATION UPGRADE. |
| 00-03-10-006M | 2017-01-18. Service bulletin. EQUIPMENT; TIRES. THIS INFORMATIONAL BULLETIN PROVIDES GUIDANCE TO GM DEALERS WHEN USING GM APPROVED TIRE FORCE VARIATION MEASUREMENT EQUIPMENT. |
| PIT5401F | 2016-11-03. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF THE RADIO IS INOPERTIVE. NEW SOFTWARE HAS BEEN RELEASED TO CORRECT THIS CONCERN. |
| PIT5389A | 2016-11-03. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS FOR DIAGNOSING THE CONCERN. THE VEHICLE MAY BE UNABLE TO CONNECT TO ONSTAR USING THE WHITE, BLUE OR RED ONSTAR BUTTONS. |
| PIP5382B | 2016-11-03. Service bulletin. ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION HAS THE STEPS FOR DIAGNOSING THE CONCERN OF EXCESSIVE OIL CONSUMPTION FOR THE GENERATION 5 ENGINE. DIAGNOSTIC INFORMATION IS PROVIDED FOR THE TECHNICIAN TO GATHER PRIOR TO CONTACTING THE PRODUCT QUALITY CENTER FOR FURTHER ASSISTANCE. |
| PIP5189B | 2016-11-01. Service bulletin. ELECTRICAL SYSTEM; ENGINE. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE AND REPAIR THE CONCERN OF BLACK SMOKE WHEN STARTING THE VEHICLE AFTER SITTING. |
| PIP5168E | 2016-11-01. Service bulletin. ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON THE STEPS TO DIAGNOSE THE CONCERN, AND THE STEPS TO REPAIR THE CONCERN OF THE VEHICLE CRANKS BUT DOES NOT START. THE TECHNICIAN IS TO INSPECT FOR A SHEARED CAM PIN IN THE ENGINE. |
| PIC6198A | 2016-11-01. Service bulletin. ELECTRICAL SYSTEM. THIS PRELIMINARY INFORMATION COMMUNICATION ADVISES THE TECHNICIAN ON STEPS TO PERFORM TO DETERMINE IF THE CUSTOMER'S BATTERY DRAIN CONCERN IS BEING CAUSED BY A KNOWN CONCERN WITH BLUETOOTH CALL TRANSFER OPERATION WHEN EXITING THE VEHICLE. IF THE CONCERN IS DUPLICATED AT THE DEALER WITH THE ONSTAR LED IS STILL GREEN AFTER THE VEHICLE IS TURNED OFF AND THE BLUETOOTH CALL WAS DISCONNECTED. DEALER SHOULD ADVISES THAT ENGINEERING IS AWARE OF THE CONCERN AND IS CURRENTLY INVESTIGATING THE ISSUE. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.