Service bulletins for the 2015 Ford Transit
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
203 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Transmission and driveline are shown. Show all
| SSM 55098 | 2026-08-25. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN; ENGINE. Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the exhaust gas sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute age requirement. There is an all-new "PCM Catalytic Converter Age Evaluation" application within the latest version of the Ford Diagnosis and Repair System (FDRS). Use this new FDRS application to determine the age (in minutes) of the DOC. If the age is less than 120 minutes, perform manual regenerations to increase the catalyst age counter to satisfy the monitor age requirement. If further assistance is needed, contact the technical assistance center (TAC). Note: this article only applies to the EGS monitor. Problems with other vehicle monitors not running successfully must be addressed using normal diagnostics located i |
|---|---|
| SSM 54366 | 2025-11-19. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern. |
| TSB 24-2099 | 2024-05-02. Service bulletin. POWER TRAIN. This article supersedes TSB 22-2444 to add 2024 model year vehicles. Some 2015-2024 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (only), and U-joints at the transmission flange and rear driveshaft may experience a boom/hum/moan noise from the rear while driving. This noise is most noticeable at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio 121-128 km/h (75-80 mph) for 3.73 axle ratio 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise may also be present to a lesser degree at roughly half of the noted speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. |
| SSM 52314 | 2024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure. |
| 23N01 | 2023-10-03. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN; FUEL SYSTEM, DIESEL. Certain 2015-2019 Model Year Transit Vehicles with 3.2L Diesel Engine - Crankcase Ventilation Hose Assembly Replacement and Powertrain Control Module Software Update |
| TSB 22-2444 | 2022-12-02. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. This article supersedes TSB 22-2271 to update the vehicle model years affected. Some 2015-2023 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (only), and U-joints at the transmission flange and rear driveshaft may experience a boom/hum/moan noise from the rear while driving. This noise is most noticeable at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio 121-128 km/h (75-80 mph) for 3.73 axle ratio 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise may also be present to a lesser degree at roughly half of the noted speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. NOTE: The torsional damper will not resolve a vibration. |
| TSB 22-2271 | 2022-07-11. Service bulletin. POWER TRAIN. This article supersedes TSB 22-2175 to update the Issue, Action, and Service Procedure. Some 2015-2022 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (only), and U-joints at the transmission flange and rear driveshaft may experience a boom/hum/moan noise from the rear while driving. This noise is most noticeable at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio 121-128 km/h (75-80 mph) for 3.73 axle ratio 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise may also be present to a lesser degree at roughly half of the noted speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. NOTE: The torsional damper will not resolve a vibration. |
| TSB 22-2175 | 2022-05-12. Service bulletin. POWER TRAIN. Some 20152022 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel only, and a U-joint at the transmission flange and rear driveshaft may experience a boom/hum/moan noise or vibration from the rear while driving. This noise or vibration is most prevalent at highway speeds: * 112-121 km/h (7075 mph) for 4.10 axle ratio * 121-128 km/h (75-80 mph) for 3.73 axle ratio * 136-145 km/h (85-90 mph) for 3.31 axle ratio The noise or vibration may also be present to a lesser degree at roughly half of those speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. |
| TSB 22-2043 | 2022-02-23. Service bulletin. POWER TRAIN. Some 2015-2021 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel only, and a U-joint at the transmission flange and rear driveshaft may experience a boom/hum/moan noise or vibration from the rear while driving. This noise or vibration is most prevalent at highway speeds: 112-121 km/h (70-75 mph) for 4.10 axle ratio, 121-128 km/h (75-80 mph) for 3.73 axle ratio, 136-145 km/h (85-90 mph) for 3.31 axle ratio. The noise or vibration may also be present to a lesser degree at roughly half of those speeds. This may be due to a 2nd order driveline frequency transmitted through the rear driveshaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. |
| TSB160001 | 2021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN; AIR BAGS; STRUCTURE. 49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C |
| LTR3756 | 2021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; AIR BAGS; ENGINE; STRUCTURE; POWER TRAIN; ELECTRICAL SYSTEM. 49 CFR Part 579.5 Monthly Communications - January 2016 |
| SSM 49821 | 2021-06-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; ENGINE AND ENGINE COOLING. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 21-2064 | 2021-04-03. Service bulletin. POWER TRAIN. Some 2015-2021 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (SRW), and a U-joint at the transmission flange and rear driveshaft may experience a boom/hum/moan noise or vibration from the rear while driving. This noise or vibration is most prevalent at highway speeds (112-121 km/h 7075 mph for 4.10 axle ratio, 121-128 km/h 75-80 mph for 3.73 axle ratio, and 136-145 km/h 85-90 mph for 3.31 axle ratio) and may also be present to a lesser degree at roughly half of those speeds. This may be due to a 2nd order driveline frequency transmitted through the rear drive shaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. |
| SSM 49483 | 2021-02-04. Service bulletin. POWER TRAIN. Some 2017-2021 F-Super Duty and 2016-2021 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition. |
| TSB 20-2214 | 2020-11-05. Service bulletin. EQUIPMENT; POWER TRAIN. Some 2015-2020 Transit vehicles equipped with rear wheel drive (RWD), single rear wheel (SRW) and a U-joint at the transmission flange and rear driveshaft may experience a boom/hum/moan noise or vibration from the rear while driving. This noise or vibration is most prevalent at highway speeds (112-121 km/h 70-75 mph for 4.10 axle ratio, 121-128 km/h75-80 mph for 3.73 axle ratio, and 136-145 km/h 85-90 mph for 3.31 axle ratio) and may also be present to a lesser degree at roughly half of those speeds. This may be due to a 2nd order driveline frequency transmitted through the rear drive shaft, rear axle and into the body through the leaf springs. To correct the condition, follow the Service Procedure to install a driveshaft torsional damper. |
| SSM 48423 | 2020-01-08. Service bulletin. POWER TRAIN. Some 2015-2020 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 48030 | 2019-07-08. Service bulletin. POWER TRAIN. Some 2015-2019 Transit vehicles may exhibit a concern where there is no 4th, 5th, or 6th gear engagement and MIL with DTC P07AA. If diagnostics lead to teardown, make sure to inspect the intermediate shafts mating splines in the rear planetary gear set for worn down/stripped splines. Refer to the Workshop Manual (WSM) diagnostics section 307-01 > DTC P07AA > Diagnosis By Symptom > Only gears R,1,2,3 > Overdrive clutch does not apply > Intermediate shaft. If the planetary splines are worn/stripped, replace as necessary. |
| SSM 48005 | 2019-06-07. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT; POWER TRAIN. If a 2015-2017 Transit vehicle originally equipped with a rubber flexible coupling requires replacement of the driveshaft assembly and/or transmission output flange, refer to the parts catalog supersession information for a complete list of the required parts. The service strategy has changed, and these repairs must now be completed by installing a new driveshaft and transmission output flange coupled with a u-joint. |
| SSM 47976 | 2019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01. |
| TSB 19-2091 | 2019-04-02. Service bulletin. POWER TRAIN; ENGINE. Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. To resolve this condition, install updated water management hardware and/or a revised air cleaner cover. |
| TSB 19-2061 | 2019-04-02. Service bulletin. POWER TRAIN; ENGINE. Some 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may exhibit Drive To Clean maintenance messages and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2459, P2463, and/or P246C. Vehicles may also exhibit frequent automatic exhaust regeneration attempts. This may be due to vehicles being used in stationary or off-highway, low speed applications. If automatic regeneration attempts are unsuccessful, these symptoms may be a result of soot accumulation in the diesel particulate filter (DPF). These vehicles may benefit from operator commanded regeneration (OCR) capability so complete regeneration cycles may be performed in a stationary setting. Some 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may exhibit Drive To Clean maintenance messages and/or an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2459, P2463, and/or P246C. Vehicles may also exhibit frequent automatic exhaust regeneration attempts. This may be due to vehicles being used in stationary or off-highway, low speed applications. If automatic regeneration attempts are unsuccessful, these symptoms may be a result of soot accumulation in the diesel particulate filter (DPF). These vehicles may benefit from operator commanded regeneration (OCR) capability so complete regeneration cycles may be performed in a stationary setting. |
| TSB 19-2012 | 2019-04-01. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2015 Transit vehicles equipped with a 3.2L engine may exhibit an illuminated MIL with DTCs P24A0 and/or P26A0 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition. |
| XLF-SFT02-12 | 2019-03-04. Service bulletin. POWER TRAIN:DRIVELINE:DRIVESHAFT. Technical Service Bulletin informing customers of XL Hybrid 130" wheel base Ford Transit vehicles that the front drive shaft of vehicles should be lubricated immediately with grease and then every 6,000 miles subsequently. |
| TSB 18-2321 | 2018-11-19. Service bulletin. ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2015-2018 Transit vehicles built on or before 24-Jul-2018 may exhibit various drivability concerns including difficulty starting, misfires and/or an illuminated MIL with diagnostic trouble codes (DTCs) P00BD, P1247, P1548, P061B, P2195, P2198, P2196, P2197, P0171, P0172, P0174, P0175, P0131 and/or P162F stored in the powertrain control module (PCM). This may be due to undesired water entry into the engine compartment directly over powertrain components. Follow the Service Procedure steps to correct the condition. |
| SSM 47039 | 2018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.