Service bulletins for the 2022 Ford Mustang Mach-E
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
224 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| SSM 52925 | 2024-09-24. Service bulletin. UNKNOWN OR OTHER. Some 2020-2024 Explorer/Aviator/Corsair, 2021-2024 F-150/Bronco, 2023-2024 F-Super Duty, and 2024-2025 Nautilus vehicles may experience the overhead console sunglass bin cannot be locked in a closed position. |
|---|---|
| 24B42 | 2024-09-05. Service bulletin. UNKNOWN OR OTHER. Certain 2021 - 2023 Model Year Mustang Mach-E Vehicles Powertrain Control Module – Coordinated Software Update In some of the affected vehicles, the vehicle may disengage the one pedal drive mode at speeds below 15 MPH accompanied by a one pedal drive fault pop-up message displayed in the instrument panel cluster. |
| TSB 24-2251 | 2024-09-02. Service bulletin. LANE DEPARTURE: ASSIST; FORWARD COLLISION AVOIDANCE: ADAPTIVE CRUISE CONTROL. This article supersedes TSB 24-2087 to update the vehicle lines, model years affected, action and service procedure. Some 2021-2024 Mustang Mach-E/F-150, 2022-2024 F-150 Lightning/Expedition/Navigator, 2023-2024 Corsair vehicles may exhibit an inoperative BlueCruise and lane centering with DTCs U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA) without DTC U3000:49 stored in the CMR. This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS). |
| TSB 24-2230 | 2024-07-29. Service bulletin. VISIBILITY/WIPER. This article supersedes TSB 24-2002 to update the symptom, production fix date and the service procedure. Some 2021-2024 Mustang Mach-E vehicles built on or before 09-Jul-2024 may exhibit a wind noise from the exterior mirrors/A-pillar area when driving between 25 mph-40 mph (32 km/h-64 Km/h). This may be due to poor sealing of the lower mirror foam and the glass top run foam. To correct this condition, follow the Service Procedure to install new lower inner foam and the glass top run foam. |
| OTA IPMA-24.204.8.27Mach | 2024-07-04. Over-the-air update. UNKNOWN OR OTHER. Quality improvements include: - Reduced ADAS loss of communication events - Adds camera retry strategy robustness action - 21 MY: Removes erroneous ""Reverse Brake Unavailable"" message. |
| TSB 24-2187 | 2024-06-13. Service bulletin. POWER TRAIN. Some 2021-2023 Mustang Mach-E vehicles may exhibit a "1 Pedal Drive Fault - Press Brake Pedal To Reduce Speed" warning message displayed in the instrument panel cluster (IPC). The customer may also notice that the 1 Pedal Drive feature has been deactivated. A diagnostic trouble code (DTC) P0C2F:92 may also be stored in the secondary on-board diagnostic module-C (SOBDMC). This concern may also be present when one pedal drive mode is enabled. This may be due to the SOBDMC. To correct the condition, follow the Service Procedure to reprogram the powertrain modules using the latest level of the Ford Diagnosis and Repair System (FDRS). |
| 24N05 | 2024-06-06. Service bulletin. STRUCTURE:BODY. Certain 2021-2023 Model Year Mach-E Vehicles - Paint Sealant Issues - Door Hems Inspection - Repair |
| SSM 52574 | 2024-06-06. Service bulletin. UNKNOWN OR OTHER. Some vehicles equipped with SYNC4 may exhibit one or more of the following symptoms after all currently available accessory protocol interface module (APIM) software updates have been performed. - General system performance, stability, and intermittent system reboots. - Intermittent Wireless CarPlay or Android Auto function. - Phone related concerns with intermittent No Audio or Static. - Navigation/global positioning system (GPS) related concerns through CarPlay and Android Auto. - Alexa function consistency and stability. These symptoms may be due to the software in the APIM. Replacing the APIM will not resolve these symptoms for the customer. Before returning the vehicle to the customer, review the procedures within Workshop Manual, Section 415-00 and ensure the latest APIM software is installed. Refer to General Service Bulletin (GSB) 23-7146 for help determining the latest available level of software. IMPORTANT: some module software updates will only display as available on Ford Diagnosis and Repair System (FDRS) after prerequisite modules are updated. This may require the technician to update certain modules multiple times during the service visit, before the latest APIM software is accessible in FDRS. If symptoms continue after latest APIM software has been installed, inform customers that Ford is working on additional software enhancements which are expected to be delivered over-the-air (OTA) by Q4 2024 on F-150, F-150 Lightning, Mustang Mach-E, Mustang, Escape, Corsair, Expedition, Navigator, Bronco, Mustang, and 2023-2024 F-Super Duty. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. For all other vehicles with SYNC4, schedule a service visit for customers in October 2024, when the updated APIM software is expected to be available to dealers. Monitor OASIS for additional information. |
| TSB 24-2163 | 2024-06-04. Service bulletin. ELECTRICAL SYSTEM. This article supersedes TSB 24-2017 to update the Service Procedure and Parts List. Some 2021-2022 Mustang Mach-E vehicles built on or before 28-May-2022 may exhibit an illuminated malfunction indicator lamp (MIL) and/or powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P0563, P0ADA, P0ADE, P0AA1, P0AA4, P0AA5, P0AA2, P0D10, P0D0F and/or P0C78 stored in the battery energy control module (BECM). It may also have a low/discharged 12V battery and/or display a Stop Safely Now message in the instrument panel cluster (IPC). This may be due to the high voltage battery junction box. To correct the condition, follow the Service Procedure to replace the high voltage battery junction box and reprogram the BECM. |
| SSM 52504 | 2024-05-17. Service bulletin. UNKNOWN OR OTHER. Some 2021-2023 Mustang Mach-E vehicles built on or before 21-Apr-2023 may exhibit a false alarm activation and/or warning message in the FordPass application when the doors are locked. This may be due to the software in the door latch control module E (DCME), door latch control module F (DCMF), door latch control module G (DCMG) and/or door latch control module H (DCMH). To correct the condition, download and run the door control module software update application for each module one at a time using the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 58219A65 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| OTAPU0301-BLM-PE | 2024-05-06. Service bulletin. ELECTRICAL SYSTEM. Quality Improvements include: - Allows the user to open any vehicle door if the phone is within 6m of the vehicle. - Improves the success rate for the Passive Entry feature. - Allows persons to enter the vehicle independent of which side the phone is located. |
| OTAPU10246CHAUDM | 2024-05-06. Service bulletin. ELECTRICAL SYSTEM. Quality improvements include: -22, 23 and 21 MYs: Fix the infrequent random audio noises and improve the audio quality of the vehicle. -23.5 MY may lose audio on rear left woofer/tweeter (Channel 1) |
| SSM 52498 | 2024-05-03. Service bulletin. UNKNOWN OR OTHER. Some 2021-2023 Mustang Mach-E vehicles may exhibit a "1 Pedal Drive Fault - Press Brake Pedal To Reduce Speed" warning message displayed in the instrument panel cluster (IPC) after a recent powertrain software update was received. A diagnostic trouble code (DTC) P0C2F:92 may also be stored in the secondary on-board diagnostic module-C (SOBDMC). This concern may also be present when One Pedal Drive mode is enabled. This condition does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected by early May 2024. Replacement or reprogramming of SOBDMC and/or the PCM will not resolve this condition. Module reprogramming in the Ford Diagnosis and Repair System (FDRS) has been temporarily suspended for powertrain modules. Monitor Professional Technician System (PTS), OASIS, and FSA landing pages for additional information and schedule service appointments for customers once the repair becomes available. |
| SSM 52410 | 2024-04-24. Service bulletin. UNKNOWN OR OTHER. Various vehicles have had pinpoint tests, guided routines and the Warranty and Policy Manual recentlyupdated for diagnostics and repairs on SYNC generation 3 and later applications. When performingdiagnostics and repairs on SYNC Gen 3 or later, select the diagnostics tab and search for related symptoms,DTCs and keywords. The search results will be shown in the search results pane. Read and follow allTechnical Service Bulletins (TSB), Special Service Message (SSM)s or General Service Bulletin (GSB) first if abulletin specifically addresses the vehicle concern. If there are no messages, run the appropriate diagnosticpinpoint test found in the Workshop Manual (WSM). Follow the steps in the pinpoint test. Make sure to note thetitle of the guided routine, using the correct one for the vehicle's symptom or diagnostic trouble code (DTC) iscritical. Depending on the outcome of the pinpoint test, a repair validation code (RVC) may be generated eitherin the pinpoint test or Guided Routine. If the vehicle concern still exists after following the pinpoint tests orguided routine, then a manual RVC can be generated using the RVC Assist Form. A manual RVC can only begenerated once the above process has been followed. |
| OTAPU0121-FTDIFX | 2024-04-04. Service bulletin. ELECTRICAL SYSTEM. Software Update 24-OTA 24-PU0121-FTDI-FX for 2021- 2022 MY Mach E vehicles is now available. Quality Improvements include: - Add electrical back drive functionality to the latch as a robustness improvement - FordPass will remember last known profile. - Allow customers to exit during OTA update. - BCM response to deinhibit request when OTA is complete - Allows vehicle to return to sleep after detecting CAN traffic, for reduced battery drain. - Perimeter alarm duty cycle for horn and light aligned with non-US market requirements. (ECE-116) - 2021 MY corrects "Frunk Fault Service Frunk" nuisance warning which may occur during OTA |
| TSB 24-2087 | 2024-04-04. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Some 2022-2023 Mustang Mach-E vehicles which recently received a software update delivered over-the-air (OTA) may exhibit an inoperative BlueCruise and lane centering with diagnostic trouble codes (DTCs) U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA). This may be due to the software level of the CMR. To correct the condition, follow the Service Procedure to reprogram the CMR module using the latest software level of the Ford Diagnosis and Repair System (FDRS). |
| SSM 52350 | 2024-04-04. Service bulletin. BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. Some 2022-2023 Mustang Mach-E vehicles which recently received an OTA update may exhibit an inoperative BlueCruise and lane centering with diagnostic trouble codes (DTCs) U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA). This may be due to the software level of the CMR. Inform customers that engineering is currently working on a solution for this condition and will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected in mid-late March 2024. The software will update automatically if vehicle connectivity is enabled on the vehicle's settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update in March 2024. Monitor OASIS for additional information. |
| TSB 24-2062 | 2024-04-03. Service bulletin. ELECTRICAL SYSTEM. Some 2022-2023 Mustang Mach-E vehicles which recently received a Ford Power-Up software updates delivered over-the-air (OTA) may exhibit an inoperative BlueCruise and lane centering with diagnostic trouble codes (DTCs) U2018:51 stored in the camera module - rear (CMR) and U0565:86 stored in the image processing module A (IPMA). This may be due to the software level of the CMR. |
| TSB 24-2058 | 2024-04-03. Service bulletin. STRUCTURE; EQUIPMENT. Some 2021-2023 Mustang Mach-E vehicles may exhibit a wind noise from the exterior mirror/A-pillar area when driving at or above 64 km/h (40 mph). This may be due to poor sealing of the lower mirror foam and the glass top run foam.. Some 2021-2023 Mustang Mach-E vehicles may exhibit a wind noise from the exterior mirror/A-pillar area when driving at or above 64 km/h (40 mph). This may be due to poor sealing of the lower mirror foam and the glass top run foam.. |
| TSB 24-2034 | 2024-04-03. Service bulletin. EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:INFOTAINMENT. 2021-2023 Mach-E vehicles may exhibit the drive mode default to normal mode while driving and <Drive Mode Not Available> message displays in the center display screen with or without Diagnostic Trouble Code (DTC) U0253 stored in the ABS module. This may be due to the software in the APIM. |
| 23H06 | 2024-04-02. Service bulletin. ELECTRICAL SYSTEM. Harvest Program 23H06 Certain 2021-2023 Model Year Mustang Mach-E and 2022-2023 Transit Battery Electric Vehicle (BEV) High Voltage Battery Module Replacement Owner letter added. Other documents submitted 02/01/24 |
| SSM 52345 | 2024-03-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Some 2022-2024 various Ford/Lincoln vehicles equipped with SYNC 4 may experience concern where customers are receiving an error message when trying to enroll in connected services. This may be due to the gateway module (GWM) software. To correct the concern, download and run the Transport and Factory Mode Deactivation app: under HS1 modules select BCM > Transport and Factory Mode > Download > Run. When the pop-up message appears for Change Vehicle Mode - Transport/Factory/Normal Mode, press OK. This will proceed to the Transport and Factory Mode Deactivation screen, select Unlock Vehicle Connectivity Settings (21 MY + Vehicles). A pop-up message appears noting Vehicle Is Now In Normal Mode, select OK. This will return to the Transport and Factory Mode Deactivation screen, select Exit. A final pop-up notification stating that the application is finished, select OK. For claiming, use causal part 14G490 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| OTAPU0105-CMR-FX | 2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. Software Update FPU 24-PU0105-CMR-FX for 2022-2023 MY Mach E vehicles is now available. Quality Improvements include - Adds robustness to the Driver State Monitoring system and increases availability of BlueCruise - 22MY Reduces false eyes-off warnings |
| TSB 24-2027 | 2024-03-07. Service bulletin. BACK OVER PREVENTION:SOFTWARE; ELECTRICAL SYSTEM. This article supersedes TSB 23-2399 to update the vehicle lines affected. 2021-2023 Mustang Mach-E and 2023 e-Transit vehicles may exhibit a condition where the high voltage battery stops charging when connected to level 1 or level 2 chargers with an illuminated malfunction indicator lamp (MIL) and diagnostic trouble code (DTC) P2C94 stored in the secondary on-board diagnostic control module A (SOBDM). This may be due to the software in the SOBDM. To correct this condition, follow the Service Procedure to reprogram the powertrain control module (PCM). |
| SSM 52280 | 2024-03-05. Service bulletin. EQUIPMENT. Some 2021-2024 Mustang Mach-E, 2022-2024 E-Transit/F-150 Lightning vehicles may have diagnostic trouble code (DTC) P1A3C stored in the off-board charger controller module (OBCC). The P1A3C is commonly set due to an interruption of the direct current (DC) fast charging process and should be disregarded. All other DTCs stored in the OBCC are to be addressed using applicable publications and/or normal diagnostics found in Workshop Manual, Section 414-03B. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.