WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ford Fusion

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

182 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
TSB 19-21722019-07-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2015-2018 Edge and 2015-2019 Fusion/MKZ/Escape/MKC vehicles equipped with a 2.0L EcoBoost engine may exhibit a low coolant level, white exhaust smoke and/or a runs rough condition with or without an illuminated malfunction indicator lamp (MIL). Diagnostic trouble codes (DTCs) may include P0300, P0301-P0304, P0316, P0217, P1285 and/or P1299 stored in powertrain control module (PCM). This may be due to coolant intrusion into the cylinder. To correct the condition, follow the Service Procedure steps to replace the long block engine assembly.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 479672019-06-06. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 478502019-05-07. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S. dealership free of charge with shipments completed 19-Apr-2019 (reference EFC07013 on FMCDealer.com). This tester will help reduce the potential for misdiagnosis and unnecessary compressor replacement. Make sure that this tester is used for warranty repairs and document the test results in the Technician Comments field. Refer to the Rotunda catalog for a video and user manual which provide detailed operating instructions.
SSM 478242019-04-08. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477902019-04-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE. Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
TSB 19-20262019-04-08. Service bulletin. EQUIPMENT; STRUCTURE. Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
SSM 478492019-04-03. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion and 2017-2019 Escape equipped with 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in WSM, Section 303-03, pressurize the cooling system to 138kPa(20 psi0 and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the engine block surface to head gasket interface is required. Carefully inspect engine block cylinders and cylinder bore bridges for erosion, pitting, and flatness. If defects with the cylinder block surface are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair. Ford has found that all returned cylinder heads pass inspection and may have been reused.
SSM 478242019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement. For claiming, use causal part 15604 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 477902019-04-01. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2019 Fusion/MKZ and 2013-2018 C-Max vehicles with 2.0L HEV/PHEV engine may exhibit multiple drivability or electrical concerns with one or more diagnostic trouble codes, being the most common P26C3, P26CA, P26D0, P2800, P2802, U019F and U0284. On Fusion/MKZ inspect connectors C146, C1651, C1812, C168C, C1717 and C134 for signs of water entry or corrosion. On C-Max, inspect connectors C134, C140, C144, C1651, C1717 and C1812 and service as necessary. NOTE: Connector C1717 is only equipped on PHEVs for both Fusion and C-Max.
TSB 19-20262019-04-01. Service bulletin. STRUCTURE. Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
TSB 19-20172019-04-01. Service bulletin. POWER TRAIN; EQUIPMENT. Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 477652019-03-04. Service bulletin. FUEL SYSTEM, GASOLINE. Some 2013-2018 C-MAX, 2013-2019 Fusion Energi, and 2017-2019 Fusion/MKZ Hybrid vehicles may exhibit an illuminated MIL with diagnostic trouble code (DTC) P04B5. This may be due to inadvertent actuation of the fuel door release button by the customer when exiting the vehicle. If the fuel filler door is not fully closed after a refueling event or the fuel filler door is open from erroneously pressing the fuel door release button, a message displays during the third drive cycle to indicate the fuel filler door is not closed and the DTC sets. Before performing Workshop Manual (WSM) diagnosis, consult the customer about the potential for accidental fuel door actuation and explain the need to fully latch the fuel door after every refueling event. Malfunction Indicator Lamp will turn off after (3) drive cycles with fuel filler door closed.
SSM 477492019-03-04. Service bulletin. EQUIPMENT. Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
TSB 18-23732019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2012-2018 Focus Electric, 2013-2017 C-Max Energi, and 2013-2019 Fusion Energi plug-in hybrid electric vehicles (PHEV) may exhibit the high voltage (HV) battery failing to charge while connected to the second Generation 120-volt electric vehicle service equipment (EVSE) charge cord. Follow the Service Procedure steps to correct the condition.
TSB 18-23612019-03-04. Service bulletin. EQUIPMENT; SEATS. Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 476492019-01-07. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. 2013 2018 C-Max, Fusion, and MKZ Hybrid vehicles using SOBDM-C module connectors do not require electrical/dielectric grease. If used it may induce module communication concerns. Codes present may be U0293 and a P0AA6. The Workshop Shop Manual (WSM) does not state to use it on these module connectors.
SSM 476382019-01-07. Service bulletin. STEERING; STEERING: STEERING WHEEL/HANDLE BAR. 2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
SSM 476352019-01-07. Service bulletin. ELECTRICAL SYSTEM. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
TSB 18-22822018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2017 Fusion Energi and C-Max Energi vehicles may exhibit an illuminated MIL with DTC P0C27 and/or P0C28. Follow the Service Procedure steps to correct the condition.
SSM 476252018-11-19. Service bulletin. ENGINE AND ENGINE COOLING. Some 2014-2019 Fusion and 2017-2019 Escape vehicles equipped with a 1.5L Ecoboost engine may exhibit coolant consumption and white smoke concern. Follow the Cooling System Pressure Test procedure in Workshop Manual(WSM), Section 303-03, pressurize the cooling system to 138 kPa (20 psi) and hold for 5 hours. If cooling system pressure drops 27.57kPa(4psi) after 5 hours and internal engine coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect cylinder block for erosion, pitting, and flatness. Defects will be between the engine block cylinders and cylinder bore bridges. If defects with the surface of the cylinder block and/or cylinder head are identified, follow WSM, Section 303-01A procedures for repairs. Complete cost cap as needed to determine the most cost effective repair.
TSB 18-23282018-11-19. Service bulletin. POWER TRAIN. Some 2013-2016 Fusion, MKZ and C-Max vehicles equipped with an HF35 transmission and built on or before 15-Aug-2015 may exhibit a thumping/rubbing or grinding noise coming from the transmission. The noise may be present in all gear ranges including neutral when the vehicle is moving but will not be present when the vehicle is stationary or in park. Follow the Service Procedure steps to correct the condition.
SSM 474892018-09-24. Service bulletin. STEERING. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.