WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ford Focus

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

140 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 469072018-01-29. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Some 2015-2018 Focus ST vehicles may exhibit MIL On with DTC's P0300 and/or P0316 store in Powertrain Control Module(PCM) memory. Vehicle may also exhibit perceived misfire after cold start until Engine Coolant Temperature(ECT) reaches 49 degrees C (120 degrees F) Install (4) new CYFS-12-YEC spark plugs and set plug gap to 1.0mm(0.040). Use ROTUNDA RTTP tool KDT165 or equivalent to gap and adjust the plugs before installing. For Drivability concerns Refer to Powertrain Control/Emissions Diagnosis (PC/ED) manual. Engineering is currently investigating this concern. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the Oasis report and submit a Global Concern Report (GCR). Continue to monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
17-22182018-01-29. Service bulletin. STRUCTURE. Some 2013-2018 Escape, Focus and C-Max vehicles may exhibit a water stained headliner after the vehicle has experienced a water leak from areas such as the roof opening panel, fixed glass, roof rails and roof ditch mouldings. Follow the procedure below to remove the water stains from the headliner after the water leak has been repaired. Follow the Service Procedure steps to correct the condition.
SSM 468502017-12-14. Service bulletin. POWER TRAIN. Some 2015-2017 Focus vehicles equipped with a dual clutch power-shift transmission may exhibit excessive engine vibration. This may be due to a binding condition with the powertrain mounts. Before replacing components, Perform the powertrain mount neutralization procedure. Refer to Workshop Manual (WSM), Section 303-00.
SSM 468142017-10-21. Service bulletin. ENGINE. Some 2014-2017 Focus ST vehicles equipped with a 2.0L gasoline turbocharged direct injection (GTDI) engine may exhibit an audible engine idle ticking noise at normal operating temperature. This is considered a normal operating characteristic and no repair should be attempted.
SSM 461022017-08-01. Service bulletin. SEAT BELTS:FRONT:RETRACTOR; SEAT BELTS. Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
SSM 460852017-08-01. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:ENGINE:OTHER FUEL TYPES:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS; ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE AND ENGINE COOLING:ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes (DTCs) when appropriate. Using these PIDs for diagnostics will lead to inaccurate results and improper ETB replacements. If a concern is intermittent and no DTCs are present, refer to historical DTCs and the PC/ED, Section 3 No DTCs Present Index chart for further information.
TSB 16-01292017-08-01. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2011-2016 Fiesta and 2012-2016 Focus vehicles equipped with a DPS6 transmission may exhibit intermittent concerns of loss of transmission engagement while driving, intermittent no start or a loss of power. These symptoms are usually accompanied by an illuminated Check Engine lamp. Additional symptoms may include messages in the message center indicating hill start assist is not available, that parking aid malfunction/service is required or the transmission PRNDL/S gear selector on the instrument cluster may flash. Diagnostic trouble codes (DTCs) U0100, U0101, U1013 and/or P0606 will be present or stored in the powertrain control module (PCM) memory. Follow the Service Procedure steps to correct the condition.
SSM 465452017-08-01. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2014-2017 Focus/C-MAX vehicles when a replacement BCM is received for a service repair may include a white Keyless Entry Card. In an effort to consolidate the complexity of BCM's only the highest level will be available for service. If the vehicle has the Keyless Entry buttons on the left door B-pillar the card needs to stay with the vehicle and shared with the customer as the keyless entry codes have changed. If the vehicle was not built with the b-pillar touch pad, discard the card, as it has no function, and cannot be added to the vehicle. If the vehicle has the stick-on wireless key pad, that keypad has it's own card, and again discard the one that came with the service BCM.
SSM 465392017-08-01. Service bulletin. ENGINE; EQUIPMENT. Some 2015-2017 Focus ST vehicles may exhibit MIL On with a perceived Misfire after cold start. Diagnostic Trouble Codes DTC's) may include P0300, P0301, P0302, P0303,P0304, and P0316. Refer to General Service Bulletin GSB) G0000106 to confirm Historical DTCs no longer confirmed or pending, but have set at least once since the last time DTCs were cleared. Refer to Workshop Manual (WSM) Section, 303-01 and Powertrain Control/Emissions Diagnosis (PC/ED) manual for normal diagnostics. To assist with the investigation use the Report A Vehicle Concern link at the bottom of the OASIS report and submit a Global Concern Report (GCR). Engineering is currently investigating this concern. Continue to monitor OASIS for updates.
SSM 465342017-08-01. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2017 Fusion Hybrid Energi built on or before 24-Mar-2017, 2012-2016 Focus Electric and 2013-2016 C-MAX Energi and equipped with a TCU may exhibit inoperative remote features via MyFord Mobile app, discharged battery, incomplete user authorization and/or accessory protocol interface module (APIM) DTC U0198 with no modem electronic serial number (ESN) displayed. To correct, perform any open TCU field service actions (FSAs). If U0198 DTC remains, remove the TCU fuse for 5 minutes then reinstall prior to programming. Reprogram the TCU using Integrated Diagnostic System (IDS) release 104.05 or higher. An internet connection is required. Calibration files may also be obtained at www.motorcraftservice.com. For claiming, use causal part 14G229 and applicable labor operations in section 10 of the SLTS manual.
SSM 464212017-05-15. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). 2013-2017 FOCUS S MODEL VEHICLES DO NOT HAVE AN OUTSIDE AMBIENT TEMPERATURE DISPLAYED IN THE IPC AND THIS FEATURE CANNOT BE ADDED. THE SENSOR IS IN THE RIGHT HAND OUTSIDE MIRROR AND IS USED BY THE POWERTRAIN CONTROL MODULE (PCM) FOR CALCULATIONS.
SSM 462102017-03-20. Service bulletin. STEERING. SOME 2010-2016 EPAS EQUIPPED VEHICLES MAY EXHIBIT STEERING RELATED NOISES. THE WORKSHOP MANUAL (WSM) DIAGNOSTIC PROCEDURES HAVE BEEN UPDATED IN SECTION 211-02. WHEN DIAGNOSING AND REPAIRING EPAS STEERING NOISES USE THE UPDATED PROCEDURES.
SSM 462072017-03-20. Service bulletin. STRUCTURE:BODY:DOOR. SOME 2013-2017 FOCUS 4-DOOR SEDANS HAVE A SINGLE DAMPENER ON THE LEFT HAND SIDE, ADJACENT TO THE LIFTING COIL SPRING, TO SLOW THE OPERATION OF THE LUGGAGE COMPARTMENT DECK LID WHEN OPENING AND CLOSING. THE LUGGAGE COMPARTMENT DECK LID IS HELD OPEN ONLY BY THE COIL SPRINGS CONNECTED TO THE HINGES. THE DAMPENER IS NOT CHARGED WITH GAS TO SUPPORT THE LUGGAGE COMPARTMENT LID LIKE THE 5 DOOR HATCHBACK LIFT CYLINDERS. REFER TO THE UPDATED WORKSHOP MANUAL SECTION 501-03 FOR ADDITIONAL INFORMATION. IT IS NORMAL FOR THE DAMPENER TO COMPRESS EASILY WHEN REMOVED FROM THE VEHICLE, UNLIKE THE HATCHBACK LIFT SUPPORT CYLINDERS.
SSM 461972017-03-20. Service bulletin. STRUCTURE:BODY:HATCHBACK/LIFTGATE:SUPPORT DEVICE/STRUT. SOME 2013-2017 FOCUS/C-MAX VEHICLES EXHIBIT A FRAYED/CUT SHORT APPEARANCE AT THE FRONT EDGE OF THE HEADLINER NEAR THE WINDSHIELD. THIS IS A NORMAL CHARACTERISTIC OF THE HEADLINER AND NO REPAIRS SHOULD BE ATTEMPTED. ON 5 DOOR FOCUS(HATCHBACK) THE EXPOSED EDGE AT THE REAR LIFT GATE AREA MAY BE DUE THE HEM LIP OUT OF POSITION (BENT) PULLING THE WEATHER STRIP OUT OF POSITION, EXPOSING THE EDGE. THE HEM LIP CAN EASILY BE REPOSITIONED AND WILL KEEP THE HEADLINER EDGE COVERED BY THE WEATHER-STRIP, WITHOUT HEADLINER REPLACEMENT.
14M02-S32017-03-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. CERTAIN 2011 THROUGH 2015 MODEL YEAR FIESTA AND 2012 THROUGH 2016 MODEL YEAR FOCUS VEHICLES EQUIPPED WITH A DPS6 AUTOMATIC TRANSMISSION - TRANSMISSION CONTROL MODULE EXTENDED WARRANTY COVERAGE
SSM 463712017-03-20. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. SOME 2012-2017 FOCUS ELECTRIC/2013-2017 CMAX ENERGI/FUSION ENERGI/2015-2017 MKC/MKZ/2016-2017 MKX AND 2017 CONTINENTAL VEHICLES OPERATING WITH A 3G TCU ON OR BEFORE 16-JAN-2017 MAY NOT RESPOND TO CUSTOMERS REMOTE COMMANDS VIA MYLINCOLN/MYFORD MOBILE PHONE APPLICATIONS. 2G NETWORKS WERE DECOMMISSIONED ON 16-JAN-2017. IF THE 3G TCU WAS OPERATING ON A 2G NETWORK, IT WILL NOT AUTOMATICALLY ATTEMPT TO RECONNECT TO THE REPLACEMENT 3G NETWORK. TO CORRECT, RESET THE TCU BY REMOVING ITS POWER FUSE FOR 5 MINUTES. IF THE CONCERN IS STILL PRESENT, FOLLOW NORMAL DIAGNOSTICS IN WORKSHOP MANUAL (WSM), SECTION 415-00. REFER TO PTS OASIS HOME PAGE FOR TCU VERSION IDENTIFICATION. FOR CLAIMING, USE CAUSAL PART 14G229 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 463582017-03-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). 2011-2017 FIESTA AND 2012-2017 FOCUS SERVICE PIGTAIL FOR TRANSMISSION CONTROL MODULE CONNECTOR C1750A IS AVAILABLE. IF REPAIRS ARE NEEDED USE PART NUMBER FU2Z-14S411-VA. REPLACEMENT OF WIRING HARNESS 12A581 IS NO LONGER REQUIRED WHEN THIS CONNECTOR NEEDS SERVICING.
SSM 463552017-03-17. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:SHIFT PATTERN INDICATOR. MULTIPLE 2014-2016 VEHICLES EQUIPPED WITH 6F35 TRANSMISSION AND BUILT ON 1-JAN-2014 AND THROUGH 31-DEC-2015 MAY EXHIBIT HARSH REVERSE ENGAGEMENT AND HARSH/DELAYED 3RD AND 5TH GEAR UP/DOWN SHIFTS WITH NO DTCS PRESENT. THIS MAY BE DUE TO A MECHANICALLY BINDING SHIFT SOLENOID B (SSB). VERIFY HARSH REVERSE AND 3RD AND 5TH GEAR SHIFT EVENTS ARE PRESENT. USING IDS, IDENTIFY THE BAND NUMBER OF SSB FOR USE WHEN ORDERING PARTS. REMOVE THE MAIN CONTROL. DISASSEMBLE AND THOROUGHLY CLEAN THE VALVE BODY AND SOLENOID BODY TO REMOVE ANY CONTAMINANTS. REPLACE SSB, REFER TO WORKSHOP MANUAL (WSM) SECTION 307-01. USING IDS, CLEAR TRANSMISSION ADAPTIVE TABLES. FOR CLAIMING, USE CAUSAL PART 7G383 AND APPLICABLE LABOR OPERATIONS IN SECTION 7 OF THE SERVICE LABOR TIME STANDARDS (SLTS) MANUAL.
SSM 463392017-03-15. Service bulletin. EQUIPMENT. SOME 2015-2017 FOCUS VEHICLES EQUIPPED WITH REMOTE START (FACTORY OR DEALER INSTALLED) MAY EXHIBIT A CLIMATE CONTROL SYSTEM THAT DOES NOT RESPOND CORRECTLY TO A REMOTE START EVENT. THIS MAY BE DUE TO THE BODY CONTROL MODULE (BCM) CONFIGURATIONS/SETTINGS. THIS MAY AFFECT HEATED SEATS, HEATED STEERING WHEEL, HEATED BACKGLASS, AND/OR FRONT DEFROSTER. VERIFY THE BCM IS AT THE LATEST LEVEL. THE ISSUE IS CURRENTLY UNDER ENGINEERING INVESTIGATION, DO NOT ATTEMPT ANY ADDITIONAL REPAIRS AT THIS TIME. MONITOR OASIS FOR FUTURE UPDATES.
SSM 463322017-03-15. Service bulletin. EQUIPMENT. REPLACING THE ORIGINAL EQUIPMENT SYNC/NAVIGATION SYSTEM WITH EITHER AN AFTERMARKET SYNC/NAVIGATION KIT OR MODIFYING ORIGINAL SYNC/NAVIGATION PARTS TO PROVIDE ADDITIONAL FEATURES IS NOT RECOMMENDED NOR SUPPORTED ON ANY FORD, MERCURY OR LINCOLN VEHICLE. ONLY APPROVED GENUINE FORD ACCESSORIES OR ORIGINALLY INSTALLED SYSTEMS ARE SUPPORTED AND CERTIFIED TO FUNCTION CORRECTLY WITH OTHER VEHICLE SYSTEMS. IF YOU SUSPECT A SYSTEM HAS BEEN MODIFIED, THE FOLLOWING RESOURCES CAN BE USED TO VERIFY ORIGINAL EQUIPMENT: MONRONEY LABEL (WINDOW STICKER), PROFESSIONAL TECHNICIAN SOCIETY (PTS) OASIS TAB SELECT SYNC OR HVBOM. FOR GENUINE FORD ACCESSORIES USE: PTS WORKSHOP TAB SELECT DEALER INSTALLED ACCESSORY OR ACCESSORY INSTALLATION.
SSM 463222017-03-15. Service bulletin. SERVICE BRAKES, AIR:ANTILOCK:WHEEL SPEED SENSOR. SOME 2015-2016 FOCUS VEHICLES IF EQUIPPED WITH REMOTE START AND BUILT ON OR BEFORE 17-OCT-2016 MAY EXHIBIT VEHICLE STALL WITH A MALFUNCTION INDICATOR LAMP (MIL) AND DIAGNOSTIC TROUBLE CODE (DTC)P1594. THIS MAY BE DUE TO WHEEL SPEED SENSOR REPORTING MOVEMENT OF THE VEHICLE WHILE STOPPED. TO CORRECT THIS CONDITION, UPDATE THE BODY CONTROL MODULE (BCM) TO THE LATEST CALIBRATION LEVEL USING INTEGRATED DIAGNOSTIC SOFTWARE (IDS) VERSION 103.03 OR HIGHER. REFER TO WORKSHOP MANUAL (WSM) SECTION 419 TO PERFORM THE BCM UPDATING PROCEDURE. MAKE SURE THE IDS IS CONNECTED TO THE INTERNET WHEN ENTERING MODULE REPROGRAMMING TO OBTAIN THE LATEST UPDATES. CALIBRATION FILES MAY ALSO BE OBTAINED AT WWW.MOTORCRAFTSERVICE.COM USE CAUSAL PART 14A068 AND APPLICABLE LABOR OPERATIONS IN SECTION 10 OF THE SLTS MANUAL.
SSM 463032017-03-15. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. THE 2012-2017 FOCUS WORKSHOP MANUAL (WSM) PROCEDURE FOR OIL PAN AND REAR MAIN OIL SEAL INSTALLATION HAS BEEN REVISED. REFER TO WSM, SECTION 303-01 REMOVAL AND INSTALLATION. THE SEALANT APPLICATION LOCATION HAS BEEN REVISED. SPECIAL ATTENTION SHOULD BE USED AT T-JOINT LOCATIONS FOR CLEANLINESS AND SEALANT APPLICATION.
SSM 462982017-03-15. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. THE EV RANGE AFTER FULLY CHARGING A 2012-2016 FOCUS ELECTRIC, 2013-2016 C-MAX/FUSION ENERGI MAY VARY AFTER EACH CHARGING EVENT. THE WINDOW STICKER INDICATES 0-19 MILE RANGE FOR 2013-2016 CMAX/FUSION ENERGI. VARIATION OF EV RANGE MAY NOT INDICATE A BATTERY OR CHARGING CONCERN. EV RANGE IS SIMILAR TO THE DTE DISPLAY ON GASOLINE VEHICLES, EV RANGE WILL VARY WITH DRIVING/OPERATING CONDITIONS. CONDITIONS INCLUDE: EXTREME OUTSIDE TEMPERATURES, TERRAIN, DRIVING STYLE, CITY OR HIGHWAY DRIVING, TIRE PRESSURE, AND USE OF ACCESSORIES. IF THE CUSTOMER REPLACES THE LOW ROLL RESISTANCE TIRES WITH A MORE AGGRESSIVE TREAD THE RANGE WILL SUFFER. USING THE CABIN HEATER AND A/C, WHICH ARE ELECTRIC, WILL ALSO DECREASE EV RANGE. TO TEMPORARILY REMOVE THE IMPACT OF DRIVING/CLIMATE HISTORY, RESET THE LIFETIME SUMMARY OR DRIVING HISTORY BY USING THE SETTINGS MENU ON THE LEFT SIDE OF THE INSTRUMENT CLUSTER, UNDER DISPLAY
SSM 462952017-03-15. Service bulletin. ENGINE. TO HELP DIFFERENTIATE ENGINE OIL LEAKS FROM OTHER POSSIBLE SOURCES, A NEW WHITE-COLORED FLUORESCENT ENGINE OIL DYE IS AVAILABLE. WORKSHOP MANUAL (WSM), SECTION 303-00 HAS BEEN REVISED TO REFERENCE THE NEW WHITE-COLORED DYE. THE NEW WHITE FLUORESCENT DYE PROVIDES A DISTINCT WHITE GLOW TO IDENTIFY ENGINE OIL LEAKS. THE NEW WHITE FLUORESCENT DYE REQUIRES A PURE UV DIAGNOSTIC INSPECTION LAMP. THE WHITE-COLORED FLUORESCENT DYE AND PURE UV LAMP ARE NOW IN THE ROTUNDA CATALOG. DYE AND LAMP PART NUMBERS. GASOLINE ONLY DYE: 1 OUNCE BOTTLE 164-TP-33200601. DIESEL ONLY DYE: 8 OUNCE BOTTLE: 164-TP-3320-0008. PURE UV DIAGNOSTIC INSPECTION LAMP 164-TP8695 OR 164-R3748.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.