WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford F-650

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

208 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 518542023-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 518492023-09-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 516912023-06-16. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN. 2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 509662022-08-02. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty/F-650/F-750 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P24D1 stored in the powertrain control module (PCM). To correct the condition, replace the particulate matter (PM) sensor. Refer to Workshop Manual (WSM), Section 303-14. For F-650/F-750 vehicles, use LC4Z-5L216-A. For F-Super Duty pickup and 203 inch wheelbase chassis cab vehicles, use LC3Z-5L216-C. For F-Super Duty 145/179/192 inch wheelbase chassis cab vehicles, use LC3Z-5L216-B. For F-Super Duty 168/169/193/205 inch wheelbase chassis cab vehicles, use LC3Z-5L216-A. Do not attempt a programmable module installation (PMI) after installation of the PM sensor. For claiming, use causal part 5L239 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 506362022-03-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE AND ENGINE COOLING; EQUIPMENT. 2011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 505492022-03-08. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2018-2020 F-150, 2017-2022 F-Super Duty and 2016-2022 F-650/F-750 vehicles equipped with a diesel engine may exhibit diagnostic trouble code (DTC) P0000 stored in the powertrain control module (PCM) after an on-demand self test. This DTC is due to a processing error in the PCM as a result of on-demand self testing. P0000 is an invalid DTC that will not illuminate the malfunction indicator lamp (MIL) and no repairs should be performed.
TSB 21-24522022-01-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2020-2021 Aviator vehicles equipped with a 3.0L PHEV powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) U0100, P1A42 and/or P1A43 stored in battery energy control module (BECM). This may be due to software in the PCM. To correct the condition, follow the service procedure to perform a coordinated flash on the powertrain control module (PCM), secondary on-board diagnostic module c (SOBDMC), anti-lock braking system (ABS) module, BECM, and battery charger control module (BCCM).
TSB 21-23682021-11-02. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble codes (DTCs) P00BD, P012F, P0181, P0474, P124C, P1247, P20EE, P205B, P2263, P2269, P2459, and/or P259F stored in the powertrain control module (PCM). This may be due to various strategies within the PCM software. To resolve this condition, update the PCM software and perform a diesel particulate filter (DPF) manual regeneration and, if necessary, a DPF parameter reset according to the Service Procedure.
TSB 21-23362021-10-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; ENGINE. Some 2018-2020 F-150 vehicles built on or before 1-Apr-2020 equipped with a 3.0L diesel engine, 2017-2019 F-Super Duty vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine and 2016-2019 F-650/F-750 vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. To correct the condition, follow the Service Procedure steps to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank.
SSM 494832021-02-04. Service bulletin. POWER TRAIN. Some 2017-2021 F-Super Duty and 2016-2021 F650-750 with 6.7L diesel engines, 2015-2019 Transit with 3.2L diesel engines and 2018-2021 F-150 with 3.0L diesel engines may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P206C in the powertrain control module (PCM). Review of repair data supports that P206C is often the result of incorrect diesel exhaust fluid (DEF) concentration. Per Powertrain Control/Emissions Diagnosis (PC/ED) Pinpoint Test (PPT) RJ, a DEF concentration reading below 28% will set P206C and cause vehicle derate. If low concentration is suspected, drain fluid and replace with known good DEF before replacing any parts. Low concentration of DEF is not a warrantable condition.
TSB 20-20122020-02-04. Service bulletin. POWER TRAIN. Some 2017-2019 F-650/F-750 vehicles equipped with a 6.7L engine, 6R140 transmission and hydraulic brakes may exhibit a driveline vibration typically during the 1500-1700 engine revolutions per minute (RPM) range. To correct the condition, follow the Service Procedure to reprogram the powertrain control module (PCM).
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 478232019-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
TSB 19-20532019-04-02. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Some 2017-2019 F-Super Duty chassis cab/dual rear wheel (DRW) pickup vehicles and 2016- 2019 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an oil consumption concern in applications where the engine is idled for extended periods of time. This may be due to high crankcase pressure as a result of the crankcase ventilation filter element becoming restricted. To resolve the concern, replace the crankcase vent oil separator. The new crankcase vent oil separator appears different from the old crankcase vent oil separator as it no longer includes a serviceable filter element.
SSM 478232019-04-01. Service bulletin. POWER TRAIN. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 475412018-12-03. Service bulletin. POWER TRAIN. Some 2017-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox - Powertrain - Service Functions - Reset/Clear Specified Function - Reset/Clear Functions - MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
SSM 475972018-11-19. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT. Some 2013-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox > Powertrain > Service Functions > Reset/Clear Specified Function > Reset/Clear Functions > MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
SSM 470392018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty, 2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508.
TSB18-20152018-05-29. Service bulletin. POWER TRAIN. Some 2017 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a fuel knock type noise at idle, illuminated MIL with one or more of the following DTCs stored in powertrain control module (PCM) memory: P0263, P0266, P0269, P0272, P0275, P0278, P0281, P0284, P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F. This may be due to incorrect learning of the injector timing within the PCM. Follow the Service Procedure steps to correct the condition.
SSM 471702018-05-21. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 469212018-01-29. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN. Some 2017 F-Super Duty vehicles with 6.7L diesel engines may exhibit a fuel knock type noise at idle with various cylinder contribution/balance DTCs and/or Fuel Injector Offset Learn DTCs. To resolve this issue please use the following procedure: 1) Make sure ECT1 and EOT are above 176Å?F (80Å?C). 2) Using the IDS or FJDS, run the Manual Injector Balance Test/Enhanced Power Balance Test under Toolbox, Powertrain, Power Balance. If the noise is gone after running the Enhanced Power Balance test, then clear the High Pressure Side Minimum Fuel Mass Adaptation tables for all cylinders, and the Crankshaft Position Sensor under Toolbox, Powertrain, Service Functions, Reset, Clear Specified Function. Do not attempt any repairs at this time. Engineering is investigating, monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 468902017-12-14. Service bulletin. FUEL SYSTEM, DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2017 F-Super Duty/2016-2017 F650-750 equipped with 6.7L diesel engines and 2015-2017 Transit equipped with 3.2L diesel engines may exhibit a MIL on with diagnostic trouble code (DTC) P206C stored in powertrain control module(PCM). This may be due to incorrect diesel exhaust fluid (DEF) concentration. Prior to performing Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test RJ, ensure DEF concentration is checked using Central Tools Refractometer tool number CEN3R201 and if DEF contamination is suspected use the Rotunda Hydrocarbon Test Kit tool number 328-480508.
tsb17-00682017-12-14. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2016-2017 F-650/750 vehicles equipped with a 6.7L engine and built on or before 21-Aug-2017 may exhibit an illuminated MIL with DTC P203B in the powertrain control module (PCM) memory. This may be due to a low voltage condition reducing the ability of the integrated reductant level sensor to monitor reductant tank fluid levels. Follow the Service Procedure steps to correct the condition.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.