WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Ford F-550

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

160 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
SSM 550982026-08-25. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN; ENGINE. Some 2013-2016 Super Duty vehicles equipped with a 6.7L diesel engine and 2015-2019 Transit vehicles equipped with a 3.2L diesel engine may not pass a state smog test due to the exhaust gas system (EGS) monitor that will not run after completing the exhaust gas sensor drive cycle located within Section 2 of the Powertrain Control/Emissions Diagnostics (PC/ED) Manual > Drive Cycles. This may be due to the vehicles diesel oxidation catalyst (DOC) age counter being under the 120-minute age requirement. There is an all-new "PCM Catalytic Converter Age Evaluation" application within the latest version of the Ford Diagnosis and Repair System (FDRS). Use this new FDRS application to determine the age (in minutes) of the DOC. If the age is less than 120 minutes, perform manual regenerations to increase the catalyst age counter to satisfy the monitor age requirement. If further assistance is needed, contact the technical assistance center (TAC). Note: this article only applies to the EGS monitor. Problems with other vehicle monitors not running successfully must be addressed using normal diagnostics located i
SSM 518542023-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS > Diagnostics tab > HVBoM > Features > Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 518492023-09-01. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 516912023-06-16. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; POWER TRAIN. 2011-2023 F-Super Duty and 2016-2024 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
SSM 506362022-03-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE AND ENGINE COOLING; EQUIPMENT. 2011-2022 F-Super Duty and 2016-2023 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit an elevated idle condition. During prolonged idle time, vehicles may experience this elevated idle to reduce unburned hydrocarbons from the SCR. The powertrain control module estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 RPM for ambient temperatures near 26°C (80°F) and may increase to 1200 RPM at -40 °C (-40°F). Vehicles may exhibit exhaust smoke and diesel exhaust fluid smell during elevated idle condition. Exhaust smoke and smell condition will not affect reliability or durability of the engine. Power take-off (PTO) use and idle set point control will disable elevated speed. It is required that the operator monitor the vehicle and adhere to any Exhaust Filter warning messages.
TSB1600572021-12-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Torqshift Transmission - Malfunction indicator lamp (MIL) diagnostic trouble codes (DTCS) P0751, P0730 and/or P2700
TSB1600012021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN; AIR BAGS; STRUCTURE. 49 CFR Part 579.5 Monthly Communications - March 2016 Air bag warning light illuminated with diagnostic trouble code (DTC) B141B and/or B141C
LTR37562021-12-20. Service bulletin. FUEL/PROPULSION SYSTEM; AIR BAGS; ENGINE; STRUCTURE; POWER TRAIN; ELECTRICAL SYSTEM. 49 CFR Part 579.5 Monthly Communications - January 2016
SSM 500962021-09-28. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING. Some 2013-2016 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an Exhaust System Fluid Fault message and a forced idle mode with various diagnostic trouble codes (DTC) stored in the powertrain control module (PCM). A video explaining how to remove the vehicle from forced idle mode has been added to the Technical Support Videos under the Technical Assistance tab on PTS. The video can be accessed using the following web link, http://site-307934.bcvp0rtal.com/detail/videos/303---engine/video/6258842975001/2013-2016-f-super-duty-exhaust-fluid-fault-procedure.
16-00602020-12-07. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Some 2012-2016 F-Super Duty vehicles equipped with a 6.2L or 6.8L engine built on or before 4/6/2016 may exhibit an illuminated malfunction indicator lamp (MIL) with DTCs P0627, P025A, P025B and/or U0109 stored in powertrain control module (PCM) memory.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 478232019-04-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
SSM 478232019-04-01. Service bulletin. POWER TRAIN. Various 2013-2019 vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P264F after powertrain control module (PCM) replacement. This DTC indicates that the engine serial number (ESN) must be programmed into the PCM. The ESN is located on PTS> OASIS> Features> Engine Serial Number. Once the ESN is obtained from the historical vehicle bill of materials (HvBOM), it can be programmed into the PCM using the appropriate Ford diagnostic scan tool. Navigate to the toolbox tab> powertrain menu> Service Functions> ESN.
18N042018-11-19. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:DIESEL; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV). Certain 2014-2016 Model Year F-250 ? F-550 and 2016 Model Year F-650 - F-750 Vehicles, With 6.7L Diesel Engine - Crankcase Ventilation Oil Separator Assembly. Certain 2018 Model Year F-150 and 2019 Model Year F-250 through F-550 Superduty Vehicles Equipped with a Diesel Engine - Powertrain Control Module Reprogramming
SSM 475972018-11-19. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); EQUIPMENT. Some 2013-2019 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated MIL with only DTC P2074 stored in the powertrain control module (PCM). This may be due to a dirty air filter, replace the filter if necessary. Do not replace the PCM or mass air flow (MAF) sensor for this concern. Instead perform a MAF parameter reset under: Toolbox > Powertrain > Service Functions > Reset/Clear Specified Function > Reset/Clear Functions > MAF Sensor. Engineering is investigating. Monitor OASIS for updates.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 464512017-05-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. 2009-2017 VEHICLES EQUIPPED WITH A 6R80, 6R100, 6R140 AUTOMATIC TRANSMISSION HAVE AN UPDATED MAIN CONTROL VALVE BODY OVERHAUL PROCEDURE. REFER TO WORKSHOP MANUAL (WSM), SECTION 307-01 FOR MAIN CONTROL VALVE BODY (7A100) OVERHAUL PROCEDURES. NOT ALL VALVE BODIES REQUIRE REPLACEMENT. INSPECT THE VALVE BODY BORES, SPRINGS AND VALVES AS DIRECTED DURING DIAGNOSIS AND REPAIR. REFER TO GENERAL SERVICE BULLETIN (GSB) G0000093 AUTOMATIC TRANSMISSION MAIN CONTROL INSPECTION FOR A VIDEO CLIP TO AID IN THE DIAGNOSIS OF THESE REPAIRS.
TSB 16-01542017-03-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). SOME 2011-2016 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L DIESEL ENGINE, MAY EXHIBIT AN ILLUMINATED MIL WITH DTCS P208E AND/OR P218F STORED IN THE POWERTRAIN CONTROL MODULE (PCM) MEMORY DUE TO UREA CRYSTALS FORMING ON THE REDUCTANT INJECTOR NOZZLE. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
TSB16-00982017-02-10. Service bulletin. POWER TRAIN; ENGINE. SOME 2011-2016 F-SUPER DUTY VEHICLES EQUIPPED WITH A 6.7L DIESEL ENGINE THAT ARE PRIMARILY IN A STATIONARY OR OFF-HIGHWAY LOW SPEED USE MAY EXHIBIT FREQUENT EXHAUST REGENERATION ATTEMPTS, DRIVE TO CLEAN MAINTENANCE MESSAGES, THE WRENCH LIGHT ON AND/OR DIAGNOSTIC TROUBLE CODE (DTC) P2459 FOR FREQUENT REGENERATION. IF REGENERATION ATTEMPTS ARE UNSUCCESSFUL, DTC P2463 MAY SET AS A RESULT OF SOOT ACCUMULATION IN THE DIESEL PARTICULATE FILTER (DPF). VEHICLES OPERATED IN THIS MANNER MAY NOT EASILY ALLOW FOR NORMAL EXHAUST REGENERATION AND MAY BENEFIT FROM OCR CAPABILITY SO THE UNIT CAN PERFORM COMPLETE REGENERATION CYCLES IN A STATIONARY SETTING. FOLLOW THE SERVICE PROCEDURE STEPS TO CORRECT THE CONDITION.
ASI-451212015-09-23. Service bulletin. POWER TRAIN:AXLE HUBS. FORD: ON SOME TRUCKS WITH ELECTRONIC 4WD SHIFT, AXLE SEAL (3254) NEEDS REPLACEMENT DUE TO VACUUM LEAKS AND IF REQUIRES REPAIR OR SERVICE, AXLE SEAL KIT IS AVAILABLE. MODEL 2011-15 F SUPER DUTY. *PE
ASI-451122015-09-22. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION. FORD: FLUID PRESSURE MALFUNCTIONS AND TRANSMISSION DAMAGE DUE TO FAILURE TO REMOVE MAIN CONTROL (7A100) AFTER PUMP REMOVAL AND REPLACEMENT (7A103). MODEL 2011-15 F-SUPER DUTY. *PE
ASI-447152015-07-08. Service bulletin. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT:SEAL. FORD: BETWEEN FRONT HUB LOCK ASSEMBLY AND FRONT AXLE SHAFT SEAL ASSEMBLY, A LOST OF VACUUM HAS OCCUR, DUE TO CONCERNS WITH FRONT AXLE HUB SEAL(S) RESULTING IN 4X4 NOT ENGAGING OR UNLOCKING OR FAILING TO STAY ENGAGED. MODEL 2013-15 F-SUPER DUTY 4X4. *PE
CSP-14N022015-02-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. FORD/LINCOLN: THERE IS AN EXTENDED WARRANTY COVERAGE FOR THE LOSS OF ABS SPEED SIGNAL RELATED COMMUNICATION THAT DISABLE OBDII SYSTEM MONITORS FOR PCM REPROGRAMMING. MODEL 2011-14 F-SUPER DUTY, ESCAPE, TAURUS, FUSION, MKT, MKZ. *PE
TSB-14-01412014-11-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:ENGINE:DIESEL; ELECTRICAL SYSTEM:SOFTWARE. FORD: WHEN THE POWER TAKE OFF (PTO) IS ENGAGED, THE ENGINE EXHIBITS AN IDLE VIBRATION AND/OR A ROUGH IDLE AND WOULD NEED TO REPROGRAM PCM TO LATEST CALIBRATION. MODEL 2013-2014 F-450, 550. *PE
TSB-14-01402014-11-26. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). FORD: AFTER DECELERATING TO STOP, VEHICLE EXPERIENCE A DELAYED ENGAGEMENT RESPONSE OF STATIONARY ELEVATED IDLE CONTROL W/POWER TAKE OFF (SEIC-PTO) MODE OPERATION. MODEL 2013-2014 F-450, 550. *PE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.