WenmarOpen by Wenmar Pro

Service bulletins for the 2011 Ford F-450

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

171 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
SSM 494302021-02-04. Service bulletin. ENGINE AND ENGINE COOLING. 2011-2021 F-Super Duty and 2016-2021 F-650/F-750 vehicles equipped with a 6.7L engine may exhibit a high/elevated idle condition. During prolonged idle time, vehicles may experience this high/elevated idle to reduce buildup of unburned hydrocarbons from the SCR system. The powertrain control module (PCM) estimates hydrocarbon levels in the SCR and may increase idle speed to remove them. Idle speed will be increased to 1000 revolutions per minute (rpms) for ambient temperatures near 26C (80F) and may increase to as high as 1200 rpms at -40 C (-40F). These elevated idle periods can last from 20-40 minutes, depending on ambient temperatures. During power take off (PTO) use and already using idle set point control, the elevated speed is disabled. It is required that the operator monitor the vehicle and adhere to the Exhaust Filter warning messages.
SSM 490652020-09-04. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL. Some 2011-2020 F-Super Duty, 2015-2019 Transit, 2016-2021 F-650/F-750 and 2018-2020 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the after treatment system. Use of these cleaning tools may void the emissions warranty of the hot end after treatment exhaust system and the attached emissions sensors.
SSM 484942020-02-04. Service bulletin. SUSPENSION. Some 2005-2020 F-Super Duty 4x4 vehicles operated in extreme dust, mud or tar sand conditions may exhibit accelerated 4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet
SSM 481392019-09-09. Service bulletin. ENGINE AND ENGINE COOLING. Some remanufactured 6.7L diesel engines recently installed in 2011-2014 F-Super Duty vehicles may exhibit a lack of power with engine oil temperature (EOT) exceeding 125Å’C (257Å’F) under loads. This may also be accompanied by REDUCED ENGINE POWER being displayed in the message center and the coolant temperature gauge indicating H. This symptom may be due to a missing metering cup plug in the upper oil pan causing reduced oil flow through the oil cooler. Remanufactured engines built on 1-Mar-2019 and through 13-May-2019 may be affected. If a vehicle exhibits this concern, use the Report a Vehicle Concern link at the bottom of the OASIS tab and submit a report. Include the engine serial number and engine build date in the report. The dealership may be contacted for further details and possible repair direction.
SSM 481302019-09-06. Service bulletin. VISIBILITY:GLASS, SIDE/REAR; VISIBILITY. Some 2010-2020 vehicles may exhibit distorted glass with a subtle orange peel pattern or streaking etched into the surface. This is caused by hydrofluoric acid which is used in some car wash solutions as a cleaning agent. Hydrofluoric acid can attack the glass and cause visual distortion and/or discoloration on the outer surface which cannot be removed by further cleaning. If this type of distortion is found, inspect the area of the glass that is covered by the cowl and/or molding. The portion of glass that is covered by the cowl or molding will not be affected by the acid. Hydrofluoric acid damage is not a defect in material or workmanship and is not a warrantable condition.
18M052019-08-07. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN. Customer Satisfaction Program 18M05 Certain 2011-2012 Model Year F-450 and F-550 Vehicles Equipped with a 6.7L Engine Turbocharger Extended Warranty Coverage
SSM 480442019-07-08. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2019 F-Super Duty vehicles equipped with a 6.7L engine may come in for scheduled maintenance on the engine mounted fuel filter. When reconnecting a fuel line quick connect fitting back onto the engine mounted fuel filter housing, push the connector all the way onto the fuel filter connection port. For some vehicles, you may need to depress a retainer clip to lock the quick connect port into place. Once the fitting is latched fully onto the connection port, pull straight backward on the fuel line to verify it is fully latched onto the connection port. Do not bend the fuel line connection when pulling to verify it is connected. Refer to Workshop Manual sections 310-00 for details on quick connect fittings.
SSM 479762019-06-07. Service bulletin. POWER TRAIN. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter hub greatly increases the likelihood of the flexplate cracking in the future. Missing dowels may cause a misalignment issue also resulting in a premature failure. Refer to Workshop Manual (WSM), Section 307-01.
SSM 479792019-06-06. Service bulletin. SUSPENSION:FRONT:WHEEL BEARING; SUSPENSION. Some 2005-2019 F-Super Duty 4x4 vehicles operated in extreme dust, mud or tar sand conditions may exhibit accelerated 4x4 vacuum hub seal and or wheel bearing wear as a result of harsh operating conditions. A knuckle seal shield kit is now available for customer purchase. The kit is designed for severe duty and is non warrantable. The knuckle seal shield kit GC3Z-54024A38-A includes an installation instruction sheet
TSB19-21432019-06-05. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2016 F-Super Duty vehicles equipped with a 6.7L diesel engine may exhibit a lack of power and/or illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0299 in the powertrain control module (PCM). This may be due to the charge air cooler (CAC) outlet tube assembly becoming disconnected at the throttle body or a separation at the CAC tube crimp clamp. To resolve this concern, follow the Service Procedure steps to replace the CAC outlet tube assembly.Follow the service procedure steps to correct the condition.
SSM 479482019-05-07. Service bulletin. ENGINE. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. When specified in the WSM, the turbocharger oil supply filter must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 478362019-04-08. Service bulletin. FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:DIESEL. Some 2011-2019 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking/tapping noise traced to the reductant injector.
SSM 478362019-04-01. Service bulletin. FUEL SYSTEM, DIESEL. Some 2011-2019 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking/tapping noise traced to the reductant injector.
18M042019-03-04. Service bulletin. ENGINE. Certain 2011-2012 Model Year 6.7L F-450-F-550 Chassis Cab Vehicles Over 14K GVWR - NOx Sensor Extended Warranty Coverage
SSM 476412019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:GAS RECIRCULATION VALVE (EGR VALVE); ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:MANIFOLD/HEADER/MUFFLER/TAIL PIPE. Some 2011-2019 F-Super Duty, 2015-2019 Transit, 2016-2019 F-650/F-750 and 2018 F-150 vehicles equipped with a 6.7L, 3.2L or 3.0L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P207F, P20EE, P229F, P2201 and/or P24AE. This may be a result of using aftermarket cleaning liquids or tools for the exhaust gas recirculation (EGR) cooler or intake. Ford does not recommend the cleaning of diesel intakes or EGR coolers using any aftermarket tool that injects a cleaning foam or liquid substance into the EGR cooler or intake. Using these types of fluids can result in sodium poisoning of the NOx and particulate matter (PM) sensors resulting in degraded operation and permanent damage to the aftertreatment system. Use of these cleaning tools may void the emissions warranty of the hot end aftertreatment exhaust system and the attached emissions sensors.
DOR-B8H4Z-112018-11-19. Service bulletin. STEERING. This SKU is a front upper ball joint. The Customer communication requested return of unsold inventory to inspect for ball studs with excessive rotational friction in the ball joint assembly. Excessive friction in the ball joint assembly may cause a perceptible increase in steering effort.
SSM 474022018-09-10. Service bulletin. FUEL SYSTEM, DIESEL; EQUIPMENT. When performing diagnostics for DTCs P2201, P2452, P2459, P246C and/or P2463, a manual regeneration and diesel particulate filter (DPF) parameter reset using the appropriate scan tool may need to be performed. To perform the manual regeneration, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Manual Regeneration. The scan tool may indicate that a regeneration of the DPF is not recommended at this time, selecting YES on this screen will allow the regeneration process to complete. To perform the DPF parameter reset, go to the Toolbox tab > Powertrain > Service Functions > Diesel Particulate Regeneration System > DPF Parameter Reset.
tsb18-21902018-09-10. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM. Some 2011-2012 F-250/F-350 and 2011-2015 F-450/F-550 vehicles equipped with a 6.7L diesel engine built on or before 9-Dec-2014 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P2043, P205C and/or P205D. Follow the Service Procedure steps to correct the condition.
SSM 470282018-06-11. Service bulletin. ENGINE. Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
SSM 470282018-05-29. Service bulletin. ENGINE AND ENGINE COOLING. Some 2011-2018 F-Super Duty 6.7L diesel equipped vehicles may exhibit a ticking noise at idle after an engine oil change. It is often referred to as Typewriter Noise because of its similarity to the sound of a mechanical typewriter. When engine temperatures reach 150 Å?F (65 Å?C) or higher, (from engine idle up to approximately 1700 RPM's), this noise can typically be heard at the front wheel well and is often isolated to the transmission bell housing or oil pan area. Typewriter Noise is not detrimental to engine function or durability and has no short or long term effects on the engine. Do not attempt repairs to eliminate this noise. This noise is characteristic of the 6.7L diesel engine and will typically cease or diminish significantly within the oil change maintenance interval.
SSM 470092018-05-29. Service bulletin. EQUIPMENT:ELECTRICAL. The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.
18M012018-05-21. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Certain 2011-2012 Model Year F-250-F-550 and 2013-2015 F-450-F-550 equipped with a 6.7L Diesel Engine - Reductant Heater and Sender Assembly Repair
SSM 470802018-05-14. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. 2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
SSM 469002018-01-29. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the on-screen instructions to complete the procedure. This procedure will transfer the existing Key ID information between the modules without the need of having 2 programmed PATS keys present. There is no need to program keys when the PCM is going to be replaced. Additional information can be found in the Workshop Manual (WSM), Section 419-01. Missing or lost keys are not warrantable.
SSM 468922017-12-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2011 2014 SuperDuty vehicles equipped with 6.7L Diesel engine may experience an exhaust leak due to broken exhaust manifold studs. New parts have been released to service this condition. Replace the exhaust manifold on the side with a broken stud. On cylinders 1,2,3,5,6 and 7 use stud part number W715713-S431. If replacing the studs on cylinders 4 and/or 8 use stud part number W717172-S900 and replace both studs and install new spacers and heat shields on the affected side(s). Refer to Workshop Manual Section 303-01. Part numbers: Heat shield left side, FC3Z-9Y427-A and DC3Z-9A462-B for the right side. Spacer part numbers: FC3Z- 00810-A. Exhaust manifold part numbers: DC3Z-9430-A (RH) and DC3Z-9431-A (LH). Exhaust Manifold Gaskets: FC3Z-9448-A. Exhaust Manifold Nut: W701706-S430

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.