WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ford F-250

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

213 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 25-23222025-07-24. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. This article supersedes TSB 25-2200 to update the parts list to add the new camshaft and tappet service kit and add F-650/F-750. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.
SSM 539942025-07-02. Service bulletin. VEHICLE SPEED CONTROL; POWER TRAIN. Some 2023-2025 F-Super Duty vehicles may exhibit a no crank/no start with diagnostic trouble code (DTC) U0100 in various modules. This condition may be due to the ground connection at G113. Inspect G113 for proper connection and tighten to 12 +/- 1.8 Nm. If condition remains after tightening G113, continue with normal diagnostics. Refer to Workshop Manual, Section 303-06 Starting System.
SSM 539732025-07-02. Service bulletin. POWER TRAIN; ENGINE. Some 2021-2024 Edge/Nautilus, 2021-2025 Bronco/Bronco Sport/E-Series/Escape/Corsair/Expedition/Navigator/Explorer/Aviator/F-150/F-Super Duty/Mustang/Ranger, and 2022-2025 Maverick vehicles may require an A/C compressor clutch assembly replacement be performed for various concerns. Workshop Manual (WSM), Section 412-00 Removal and Installation has been updated to eliminate the need to remove and install the A/C compressor to change out the A/C Compressor clutch assembly.
SSM 539722025-07-02. Service bulletin. POWER TRAIN; ENGINE. Some 2023-2025 F-Super Duty vehicles equipped with a 6.7L engine may require replacement of the air conditioning compressor due to various concerns. Workshop Manual (WSM), Section 412-00 has been updated with improved removal and installation service procedure steps.
SSM 538962025-06-19. Service bulletin. POWER TRAIN. Some 2023-2025 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with cylinder injection pulse offset diagnostic trouble codes (DTCs) P2B11, P2B13, P2B15, P2B17, P2B19, P2B1B, P2B1D, and/or P2B1F stored in the powertrain control module (PCM) when operating at elevations greater than 2500 feet (762 meters). If symptoms are present, perform the "Reset Minimum Fuel Mass Adaption - All Cylinders" using the "Reset/Clear Specified Function" application with Ford Diagnosis and Repair System (FDRS) and retest. If the concern remains, refer to the Workshop Manual, Section 303-04 for additional diagnostics. If the symptoms are no longer present, no additional diagnosis or service is recommended for this condition at this time. Inform customers engineering is currently working on a solution for this condition that is expected in Q3 2025. Monitor PTS for additional information and schedule service appointments for customers once the repair becomes available. If this condition is encountered, use the "Submit Global Concern Report (GCR)"
SSM 538792025-06-11. Service bulletin. POWER TRAIN. Some 2020-2025 F-Super Duty vehicles equipped with a 10R140 automatic transmission may exhibit a delayed engagement into drive and/or reverse on initial start-up. The condition may occur at times after sitting overnight or for a couple of days. This may be due to the transmission fluid draining back from the torque converter. This is a normal characteristic of the 10R140 transmission and has no effect on durability, do not attempt to repair. Advise the customer to allow more time after first engine start-up and before shifting into gear allowing time for the torque converter to refill.
TSB 25-22002025-05-21. Service bulletin. ENGINE; POWER TRAIN. Some of the vehicles listed in the Model statement above may exhibit an upper engine ticking or tapping noise at idle. Customers may also report experiencing rough engine performance, engine misfire, or a malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P0301-P0308 in the powertrain control module (PCM). This may be due to camshaft and/or valve tappet having excess wear within the engine assembly.
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
TSB 24-22562024-09-02. Service bulletin. POWER TRAIN. Some 2023-2024 F-Super Duty vehicles built on or before 22-Jul-2024 and equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P203B, P206B, and/or P2201:92 stored in the powertrain control module (PCM). This may be due to the software in the PCM. To correct the condition, follow the Service Procedure to reprogram the PCM using the latest software level of the Ford Diagnosis and Repair System (FDRS) scan tool.
TSB 24-21422024-06-12. Service bulletin. POWER TRAIN. This article supersedes TSB 23-2376 to update the Part List and the Service Procedure. Some 2022-2024 F-550 and F-600 F-Super Duty vehicles equipped with a 10R140 automatic transmission and 6.7L diesel engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the transmission control module (TCM) with poor shift quality and over 5,000 miles (8,000 km) in service. This may be due to wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. To correct this condition, follow the Service Procedure to replace the E clutch hub and input shaft O-rings.
SSM 525952024-06-10. Service bulletin. POWER TRAIN. When replacing the E clutch hub (7P211) on 2020-2024 F-Super Duty and 2024-2025 F-650/F-750 vehicles equipped with a 10R140 transmission, a new washer (7482) has been added and must be installed with the new updated E clutch hub. Refer to the Workshop Manual (WSM), Section 307-01B for proper installation of the washer. Refer to the parts catalog for the appropriate part numbers for the E clutch hub and the washer.
24B272024-06-06. Service bulletin. POWER TRAIN; UNKNOWN OR OTHER. Certain 2023-2024 Super Duty and 2021-2025 Model Year Econoline Equipped With a 6.8L or 7.3L Gasoline Engine - Powertrain Control Module Software Update
SSM 525762024-06-06. Service bulletin. POWER TRAIN. 2023-2024 F-Super Duty/F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2023-2025 F-650/F-750/E-Series vehicles equipped with a Dana rear axle and built on or after 01-Nov-2022 may have orange/red RTV sealant used as the gasket on the differential housing cover. This does not indicate any previous repairs as it is used by Dana during assembly.
SSM 525482024-05-23. Service bulletin. POWER TRAIN. Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 524232024-04-25. Service bulletin. POWER TRAIN. Some 2024 F-Super Duty non-Tremor vehicles equipped with four-wheel drive (4WD) may exhibit a slight rotational grinding noise from the front axle while driving in two-wheel drive (2WD). If the noise does not occur with the vehicle driven in 4WD, this may be due to the non-selectable right side hublock on the front axle. To correct the condition, replace the right front hublock with a selectable hublock, service part number PC3Z-3B396-A. Refer to Workshop Manual (WSM), Section 307-07A. Vacuum lines with service base part numbers 3C125 and/or 3C124 may need to be installed if not present on the vehicle. Refer to the parts catalog. Suspension modifications may contribute to the concern. Inspect the vehicle for aftermarket levelling or lift kits as well as aftermarket caster/camber adjusting sleeves. If any vehicle modifications are present, this is not a warrantable repair. Do not submit a claim. Use the Report a Vehicle Concern link at the bottom of the OASIS report to submit a report detailing the presence or lack of aftermarket equipment with photos attached to the report. Reference this article by number in the text of the report.
SSM 523892024-04-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN:MANUAL TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2022-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with only diagnostic trouble code (DTC) U3012 stored in the PCM. If no drivability concerns or other DTCs are present, perform normal diagnostics per the Workshop Manual (WSM). If diagnostics lead to the powertrain control module (PCM) or body control module (BCM), the replacement of the PCM and/or the BCM will not resolve this concern. This illuminated MIL with DTC U3012 does not affect vehicle durability and no additional diagnosis or service is required for this condition at this time. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
TSB 24-20662024-04-03. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. This TSB supersedes article 24-2036 to update the vehicles affected. Some 2023-2024 F-Super Duty pickup vehicles built on or before 02-Jan-2024 equipped with a 6.7L engine may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0133, P0139, and/or P0145 stored in the powertrain control module (PCM). This may be due to the software in the PCM and does not affect vehicle operation.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 522992024-03-05. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2023-2024 F-Super Duty vehicles equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) U02A2, P206B, P203B, P208A, P20FA, P20FD, and/or P20FC stored in the powertrain control module (PCM). Before performing normal diagnostics, inspect connectors C1273C (32 pin) and C406 (14 pin) for proper connection. Also disconnect and inspect C1415 (32 pin), C406 (14 pin), C4863 (7 pin) and C4864 (5 pin) on the 14405 vehicle harness for signs of terminal push out, water intrusion and/or corrosion. Refer to the Wiring Diagram for connector locations. Repair as necessary. Refer to Wiring Diagram Cell 005 for repair procedures.
SANVol 2 Issue 12024-02-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN; ELECTRICAL SYSTEM. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.