WenmarOpen by Wenmar Pro

Service bulletin SSM 53994

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11020080
Published by NHTSA2025-07-02
Manufacturer's numberSSM 53994
Manufacturer's date2025-06-30
NHTSA componentVEHICLE SPEED CONTROL; POWER TRAIN

NHTSA's summary

Some 2023-2025 F-Super Duty vehicles may exhibit a no crank/no start with diagnostic trouble code (DTC) U0100 in various modules. This condition may be due to the ground connection at G113. Inspect G113 for proper connection and tighten to 12 +/- 1.8 Nm. If condition remains after tightening G113, continue with normal diagnostics. Refer to Workshop Manual, Section 303-06 Starting System.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Throttle and cruise control, Transmission and driveline

Trouble codes named

U0100

Vehicles listed
FORD F-250 SD2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it)
FORD F-350 SD2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it)
FORD F-450 SD2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it)
FORD F-550 SD2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20260972026-03-03. Powertrain
26V1190002026-03-03. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT
20253962025-07-25. Powertrain
20251332025-03-14. Powertrain
25V1630002025-03-14. POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
23V7580002023-11-09. WHEELS:LUGS/NUTS/BOLTS/STUDS; POWER TRAIN:AXLE HUBS
20234782023-08-29. Powertrain
23V5950002023-08-25. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
TSB 26-2375 v22026-10-13. Service bulletin. NOTE: This bulletin has been updated, refer to the change log at the bottom for details. Issue: Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: • Poor shift quality • Illuminated powertrain malfunction (wrench) indicator with DTCs P2704 and P0771 stored in the PCM / TCM . This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing theinput shaft O-rings to become damaged resulting in an open E clutch circuit. Action: For vehicles that meet all of the criteria in the Issue and Model statements, follow the Service Procedure toreprogram the PCM / TCM and/or replace the E clutch hub and input shaft O-rings
SSM 552182026-10-06. Service bulletin. For 20202026 vehicles equipped with the 10R140 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
TSB 26-22522026-09-12. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the powertrain control module (PCM)/transmission control module (TCM) This may be due to the software in the TCM (diesel only) and/or sticking valves in the main control valve body and/or damaged E clutch friction plates and E clutch steel plates. Additional model information: 6.7L Diesel Engine 7.3L Gas Engine 10R140 Automatic Transmission
TSB 26-23752026-08-19. Service bulletin. This article supersedes TSB 26-2050 to increase the labor operation allowance of labor operations A and B. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km)
SSM 549752026-07-07. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12650D, 12650D45, and 12650D81.
SSM 549002026-06-09. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12651D, 12651D45, and 12651D80.
TSB 26-22632026-06-05. Service bulletin. This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
TSB 26-22512026-06-05. Service bulletin. This article supersedes TSB 25-2545. Reason for update: To correct the current Pinpoint Test description. Some of the vehicles listed in the Model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
SSM 547382026-04-14. Service bulletin. Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op
26E012026-04-07. Other. Certain 2023 - 2026 Model Year F-250 – F600 Super Duty Vehicles with 6.7L Engines Powertrain Control Module (PCM) Software Update The affected vehicles were originally manufactured with Powertrain Control Module (PCM) software that did not provide the correct warnings when certain conditions are present in the Selective Catalyst Reduction (SCR) system as required and described in the Owner’s Manual.