Transport Canada recall 2026097
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2026097 |
| Manufacturer's number | 26S13 |
| Reported | 2026-03-03 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 567 |
What is wrong
Issue:
On certain vehicles, the rear driveshaft may not have been welded properly. As a result, the driveshaft could separate and cause a loss of power to the wheels.
Note: This recall also affects certain incomplete vehicles.
Safety Risk:
A loss of power to the wheels could increase the risk of a crash.
Corrective Actions:
Ford will notify owners by mail and advise you to take your vehicle to a dealership to inspect and, if necessary, replace the rear driveshaft.
| 2025 FORD F-250 CHASSIS CAB | Listed as a series or trim of this model. |
|---|---|
| 2026 FORD F-250 CHASSIS CAB | Listed as a series or trim of this model. |
| 2025 FORD F-250 SUPER DUTY | Listed as a series or trim of this model. |
| 2026 FORD F-250 SUPER DUTY | Listed as a series or trim of this model. |
| 2025 FORD F-350 CHASSIS CAB | Listed as a series or trim of this model. |
| 2026 FORD F-350 CHASSIS CAB | Listed as a series or trim of this model. |
| 2025 FORD F-350 SUPER DUTY | Listed as a series or trim of this model. |
| 2026 FORD F-350 SUPER DUTY | Listed as a series or trim of this model. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| SSM 55218 | 2026-10-06. Service bulletin. For 20202026 vehicles equipped with the 10R140 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement. |
|---|---|
| TSB 26-2406 | 2026-09-12. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the powertrain control module (PCM)/transmission control module (TCM) This may be due to sticking valves in the main control valve body and/or damaged E clutch friction plates and/or E clutch steel plates. Additional model information: 6.7L Diesel Engine 7.3L Gas Engine 10R140 Automatic Transmission |
| TSB 26-2252 | 2026-09-12. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the powertrain control module (PCM)/transmission control module (TCM) This may be due to the software in the TCM (diesel only) and/or sticking valves in the main control valve body and/or damaged E clutch friction plates and E clutch steel plates. Additional model information: 6.7L Diesel Engine 7.3L Gas Engine 10R140 Automatic Transmission |
| SSM 54975 | 2026-07-07. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12650D, 12650D45, and 12650D81. |
| SSM 54900 | 2026-06-09. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12651D, 12651D45, and 12651D80. |
| TSB 26-2263 | 2026-06-05. Service bulletin. This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC). |
| TSB 26-2251 | 2026-06-05. Service bulletin. This article supersedes TSB 25-2545. Reason for update: To correct the current Pinpoint Test description. Some of the vehicles listed in the Model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). |
| ECM-26.10.0 SuperDuty | 2026-05-15. Over-the-air update. 26E01 Recall remedy -Powertrain Control Module calibration update to ensure emissions system restrictions function properly when the vehicle is parked. |
| SSM 54738 | 2026-04-14. Service bulletin. Some 2023-2025 Escape 1.5L/F-Super Duty/Transit vehicles may exhibit a lack of cooling from the heating, ventilation, and air conditioning (HVAC) system, which may be accompanied by abnormal rattling, grinding and/or squealing noises from the engine compartment. This may be due to damage to the air conditioning (A/C) compressor internal components and/or clutch assembly. Confirm ambient air temperature is above approximately 0°C (32.0°F). On the HVAC controls, set the temperature to full cold (not MAX A/C), select PANEL, set the fan speed to the highest setting and select the A/C button (indicator on). If the A/C compressor clutch engages and the A/C compressor is noisy, and/or the belt is slipping on the A/C compressor pulley or the A/C compressor is seized, install a new A/C compressor as indicated in Section 412-00 of the Workshop Manual (WSM). For claiming, use causal part 19703 and labor operation MT19700SSM up to 0.3 hours to check for a damaged compressor. If the compressor requires replacement, claim labor operations 19700A and 19700A4. Also claim available Service Labor Time Standards (SLTS) op |
| 26E01 | 2026-04-07. Other. Certain 2023 - 2026 Model Year F-250 – F600 Super Duty Vehicles with 6.7L Engines Powertrain Control Module (PCM) Software Update The affected vehicles were originally manufactured with Powertrain Control Module (PCM) software that did not provide the correct warnings when certain conditions are present in the Selective Catalyst Reduction (SCR) system as required and described in the Owner’s Manual. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.