WenmarOpen by Wenmar Pro

Service bulletin TSB 26-2406

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id11037298
Published by NHTSA2026-09-12
Manufacturer's numberTSB 26-2406
Manufacturer's date2026-09-05
NHTSA componentUNKNOWN OR OTHER; POWER TRAIN

NHTSA's summary

Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTCs) P2704 and P0771 stored in the powertrain control module (PCM)/transmission control module (TCM) This may be due to sticking valves in the main control valve body and/or damaged E clutch friction plates and/or E clutch steel plates. Additional model information: 6.7L Diesel Engine 7.3L Gas Engine 10R140 Automatic Transmission

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Trouble codes named

P0771, P2704

Vehicles listed
FORD F-250 SD2026 (the catalog's model; the bulletin names a series or trim of it)
FORD F-350 SD2026 (the catalog's model; the bulletin names a series or trim of it)
FORD F-450 SD2026 (the catalog's model; the bulletin names a series or trim of it)
FORD F-550 SD2026 (the catalog's model; the bulletin names a series or trim of it)
FORD F-650 SD2026 (the catalog's model; the bulletin names a series or trim of it)
FORD F-750 SD2026 (the catalog's model; the bulletin names a series or trim of it)

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20260972026-03-03. Powertrain
26V1190002026-03-03. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT
20256882025-12-12. Powertrain
25V8660002025-12-12. POWER TRAIN:AXLE ASSEMBLY:AXLE SHAFT

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 552182026-10-06. Service bulletin. For 20202026 vehicles equipped with the 10R140 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
SSM 549762026-07-07. Service bulletin. Some 2023-2026 F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2024-2026 F-650/F-750/E-Series vehicles equipped with a 6R140 transmission may be limited to 5th gear and reverse gear only. Additionally, the driver will be able to shift back to park. Diagnostic trouble codes (DTC) P2701, P2704, P0757, and/or P0733 may be stored in the powertrain control module (PCM). This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SOC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on tr
SSM 549752026-07-07. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12650D, 12650D45, and 12650D81.
SSM 549002026-06-09. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a 10R100 or 10R140 transmission may exhibit an intermittent failure to engage forward or reverse gears and/or a loud whining noise. Additionally, the driver will be able to shift back to park. This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SoC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition. Inform the customer that the condition has no impact on transmission durability. For claiming, use causal part 12A650 and labor operations 12651D, 12651D45, and 12651D80.
SSM 548992026-06-09. Service bulletin. Some 2023-2026 F-53 Motorhome Chassis/F-59 Commercial Stripped Chassis and 2024-2026 F-650/F-750/E-Series vehicles equipped with a 6R140 transmission may be limited to 5th gear and reverse gear only. Additionally, the driver will be able to shift back to park. Diagnostic trouble codes (DTC) P2701, P2704, P0757, and/or P0733 may be stored in the powertrain control module (PCM). This may be due to PCM software being unable to command the transmission solenoid clutch actuators when the battery has a low state of charge (SOC) and/or the vehicle has been jump started. To restore proper transmission functionality, charge the battery as stated in the Workshop Manual (WSM), Section 414-01 Charging System > General Information. Cycle the ignition on then off and leave the vehicle off for 5 minutes to confirm the condition is no longer present. To prevent this issue from reoccurring, refer to the Owner's Manual > Storing Your Vehicle > Preparing Your Vehicle for Storage > 12V Battery. Replacement of transmission components will not resolve this condition.
TSB 26-22632026-06-05. Service bulletin. This bulletin supersedes 26-2112. Reason For Update: add 2026 model year vehicles, update LV fluid XT-10-QLVC and CXT-10-LV6 description to add "Transfer Case Fluid 4WD Only", and update Step 4 to inspect/replace 7H351 and 7B177 outside of this article. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: - No upshift past second gear - Unable to achieve third gear ratio - Illuminated MIL with DTCs P0757 and P2701 This may be due to a damaged one-way clutch (OWC).
ECM-26.10.0 SuperDuty2026-05-15. Over-the-air update. 26E01 Recall remedy -Powertrain Control Module calibration update to ensure emissions system restrictions function properly when the vehicle is parked.
26E012026-04-07. Other. Certain 2023 - 2026 Model Year F-250 – F600 Super Duty Vehicles with 6.7L Engines Powertrain Control Module (PCM) Software Update The affected vehicles were originally manufactured with Powertrain Control Module (PCM) software that did not provide the correct warnings when certain conditions are present in the Selective Catalyst Reduction (SCR) system as required and described in the Owner’s Manual.
SSM 545922026-02-27. Service bulletin. For 20172026 vehicles equipped with a 10R transmission, a revision to the Road Testing Vehicle procedure has been made in the WSM, located in Section 307-01 > Diagnosis and Testing. This updated procedure improves the diagnosis of customer reported transmission concerns and aids in locating the proper root cause. During diagnosis and testing, details regarding whether the condition is more prevalent when the vehicle is hot or cold, throttle percentage at the time of occurrence, vehicle speed, the specific shift involved, and whether the issue occurs during transmission engagements (N>R, N>D, R>D, or D>R) should be noted. Engineering requests including these detailed operating conditions that will significantly assist with root cause analysis. Diagnosis, testing, and repair should use established labor times outside this article.
SSM 545592026-02-12. Service bulletin. Some 2026 F-Super Duty and F-650/F-750 vehicles equipped with a 10R140 automatic transmission may exhibit fluid leakage from the transmission fluid pan area. Prior to performing any repairs, thoroughly clean the transmission fluid pan area to ensure accurate identification of the leak source. Before replacing the transmission fluid pan or gasket, verify the torque of the fluid pan bolts and stud bolts. If the torque is incorrect, tighten the pan bolts and stud bolts to the specified torque following the proper torque sequence in Workshop Manual (WSM), Section 307-01. After tightening, verify that the leak has been repaired. If the pan bolts and stud bolts are already torqued correctly, proceed with standard leak diagnosis. Should the diagnosis indicate that pan replacement is required, mark the area of the pan where the leak is present. This information will assist engineering with root cause analysis. For claiming, use causal part 7A194 and labor operation 7000E.