WenmarOpen by Wenmar Pro

Service bulletins for the 2024 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

336 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
TSB 25-22462025-06-10. Service bulletin. POWER TRAIN. This article supersedes TSB 25-2165 to update the labor operation allowance and update the Service Procedure. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.
SSM 537642025-05-21. Service bulletin. POWER TRAIN; ENGINE. Some 2020 Continental, 2020-2024 Edge/Nautilus, 2020-2025 Explorer/Aviator/Escape/Corsair/F-150/F-Super Duty/Ranger/Transit/E-Series, 2021-2025 Bronco, and 2022-2025 Maverick vehicles may require an engine cooling system flush to be performed for various concerns. Workshop Manual (WSM), Section 303-03 has been updated to eliminate the need to remove and install the radiator assembly to perform a radiator flush.
TSB 25-21652025-05-14. Service bulletin. POWER TRAIN. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2450 stored in the powertrain control module (PCM). This may be due to the software level of the PCM.
TSB 24-22602024-09-02. Service bulletin. POWER TRAIN. Some 2024 F-150 vehicles built on or before 08-Aug-2024 and equipped with a 3.5L PowerBoost engine may exhibit an illuminated MIL with DTC P144B stored in the powertrain control module (PCM). This may be due to the software level of the PCM. To correct this condition, follow the Service Procedure to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
TSB 24-22532024-09-02. Service bulletin. POWER TRAIN. Some 2021-2024 F-150 non-Lightning vehicles may exhibit a condition where the SelectShift®/SelectShift transmission will downshift to a lower gear when in drive (D) and shifting to a higher gear will be unavailable in the IPC. Downshifting may continue, when safe entry conditions are met for each gear, and the IPC display will show the available gears counting down one by one as the vehicles' speed and engine rpm decreases. This may be due to a chafed wire harness in the SelectShift® +/- circuit. To correct the condition, follow the Service Procedure to repair the circuit.
TSB 24-22002024-08-19. Service bulletin. POWER TRAIN. Some 2024 F-150 vehicles built on or before 14-May-2024 equipped with a 3.5L PowerBoost may exhibit an illuminated MIL with DTC P2C90 stored in the powertrain control module (PCM). To correct this condition, perform the Service Procedure to to inspect the positive crankcase ventilation (PCV) system and reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
TSB 24-21892024-07-01. Service bulletin. POWER TRAIN. Some 2021-2024 F-150 non-Raptor vehicles equipped with 4WD and ESOF transfer case (minor feature code FMLAS) may exhibit an intermittent grinding/hum/rumble noise from the front wheel area while in 2WD that goes away when the vehicle is put into 4WD. These vehicles will also have no diagnostic trouble codes (DTCs) stored in the transfer case control module (TCCM). To confirm a vehicle is built with a certain minor feature code, review the build information by double-clicking the vehicle identification number (VIN) in the upper left corner in the Professional Technician System (PTS). This may be due to incomplete disengagement of the integrated wheel end (IWE) actuator assemblies. To correct this condition, follow the Service Procedure to replace IWE actuator assemblies
TSB 24-21912024-06-19. Service bulletin. POWER TRAIN. Some 2024 F-150 vehicles built on or before 14-May-2024 equipped with a 3.5L PowerBoost may exhibit an illuminated MIL and set cylinder misfire DTCs P0300, P0316, P0301, P0302, P0302, P0304, P0305 and/or P0306. This may be due to the software level of the powertrain control module (PCM). To correct this condition, perform the Service Procedure to reprogram the PCM to the latest software level via the Ford Diagnosis and Repair System (FDRS).
SSM 526102024-06-11. Service bulletin. POWER TRAIN. Some 2021-2024 F-150 and 2023-2024 Expedition/Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit a rattle/scraping noise from the bellhousing area on start-up. This may be due to the torque converter studs contacting the engine-to-transmission spacer plate (separator plate). To correct this condition, remove the transmission and flexplate and inspect the engine-to-transmission spacer plate and torque converter studs for wear/damage. If wear/damage is found, replace the engine-to-transmission spacer plate. Refer to Workshop Manual (WSM) Section 303-01 Engine - 3.5L EcoBoost (BM), Removal and Installation, Crankshaft Rear Seal. When reinstalling the starter motor, make sure the starter is flush with the engine-to-transmission spacer plate prior to tightening the studbolts. Failure to do so may result in damaging the newly installed engine-to-transmission spacer plate.
SSM 525482024-05-23. Service bulletin. POWER TRAIN. Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 523182024-03-20. Service bulletin. UNKNOWN OR OTHER; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Some 2024 F-150 vehicles equipped with a 3.5L PowerBoost may set incorrect cylinder misfire DTCs while the CSER monitor is active. The CSER monitor runs for approximately 3 minutes after a cold soak start-up. If a misfire occurs while the CSER monitor is running, the powertrain control module (PCM) software strategy may set an incorrect cylinder misfire code. Prior to a repair attempt, allow the vehicle to run for at least 3 minutes and verify any individual cylinder misfire codes by performing a Power Balance Test using the Ford Diagnostic and Repair System (FDRS) scan tool. Engineering is currently working on a solution for this condition and will be released via Ford Power-Up software updates delivered over-the-air (OTA) expected in Q3 2024. Software will update automatically if vehicle connectivity is enabled in the vehicle's settings. Schedule a service visit for customers who have disabled vehicle connectivity or who report that they did not receive the update in Q3 2024. Monitor OASIS for additional information.
SSM 523142024-03-20. Service bulletin. POWER TRAIN. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
SSM 523092024-03-20. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. Some 2024 F-150 vehicles may set diagnostic trouble code (DTC) P0534:00 in the powertrain control module (PCM) when a diagnostic self-test is performed. This may be due to the PCM responding to large changes in ambient temperatures from warm to below freezing when the vehicle has less than 62 miles (100 km) and still in a rapid learn mode for the ambient air temperature logic. The rapid update to the temperature can result in the vehicle setting this DTC. DTC P0534:00 does not affect vehicle drivability and has no effect on vehicle operation. No additional diagnostics or service is required for this condition at this time. DTC P0534:00 is a background diagnostic code for service only and does not illuminate the malfunction indicator lamp (MIL), powertrain malfunction indicator (wrench), or provide any indication to the vehicle operator. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2024. Replacement or reprogramming of the PCM will not resolve this condition. Monitor OASIS for additional informati
SANVol 2 Issue 12024-02-06. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); POWER TRAIN; ELECTRICAL SYSTEM. The Service Awareness Newsletter is an informal communication that contains information that may not be presently available in a TSB, SSM, GSB, or other electronic communication. This artile includes ifnormation on warranty, technical service tips and other service information.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.