WenmarOpen by Wenmar Pro

Service bulletins for the 2020 Ford F-150

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

247 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
SSM 508042022-06-01. Service bulletin. ELECTRICAL SYSTEM. Some 2013-2023 Ford or Lincoln vehicles with modems activated through FordPass or LincolnWay may experience 12 volt battery drain symptoms when the customer uses non-Ford/Lincoln phone applications as an alternate channel to access vehicle commands such as door lock/unlock, remote start, vehicle location, etc. The battery drain may be caused by excessive calls for data through the vehicle network keeping it in an activated state. Recommend that the customer uninstall the app to ensure this is not contributing to battery symptoms experienced. Advise the customer that unaffiliated third-party app developers do not work directly with Ford to adhere to security, vehicle communication, and privacy requirements.
TSB 22-21912022-05-24. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2021 F-150 vehicles equipped with a 3.0L diesel engine, 2016-2022 F-650/F-750 vehicles equipped with a 6.7L engine, and 2017-2022 F-Super Duty vehicles equipped with a 6.7L engine and built on or before 08-Mar-2022 may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. This may also be due to movement of the wiring harness causing terminal fretting. To correct the condition, follow the Service Procedure to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank, as well as securing the wiring harness using a cable zip tie fastener.
SSM 506612022-04-13. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Some 2018-2022 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with Diagnostic Trouble Codes (DTCs) P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds (F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2022 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2022 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
SSM 503752021-12-27. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. Some 2016-2021 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit a condition where the navigation voice prompts are inoperative after a SYNC map update. This may be due to an incomplete installation of the SYNC map software. If possible, using the original USB that installed the update, reperform the update and verify the navigation voice prompts have returned. Multiple reboots are expected when this update is being performed. Verify the Installation Is Complete message displays in the touch screen. If the original USB is not available, go to website https://syncnavigation.com/ford/home or https://syncnavigation.com/lincoln/home to download the files once more for the affected vehicle. For further map update support, reference the FAQ section on these websites.
TSB 21-24112021-12-01. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. This article supersedes TSB 21-2342 to update the Issue, Action, and Service Procedure. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns including but not limited to: Sirius audio not functioning properly after a key cycle with active subscription Presets not responding or indicating properly Intermittent audio echo/robotic voice heard during a Bluetooth phone call Wi-Fi connection message pop-up every key cycle Frozen unresponsive touchscreen Solid blue screen when moving forward at speeds above 16 km/h (10 mph) (2019 vehicles only) Rear parking aid camera remains on the screen at speeds below 16 km/h (10 mph) (2019 vehicles only) Inoperative infotainment applications Poor/no AppLink function Apple CarPlay not launching on connection or a black screen when connected Voice prompts that skip or have short pauses while directions are being provided
TSB 21-23422021-11-02. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure to update the accessory protocol interface module (APIM) software.
TSB 21-23362021-10-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM; ENGINE. Some 2018-2020 F-150 vehicles built on or before 1-Apr-2020 equipped with a 3.0L diesel engine, 2017-2019 F-Super Duty vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine and 2016-2019 F-650/F-750 vehicles built on or before 30-Oct-2019 equipped with a 6.7L engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P21DD, P20BA. P20B9, P204C, P208A, P208B, P208C, P203B, P205B, P21CD and/or U02A2 in the powertrain control module (PCM). This may be due to water intrusion within connectors C3613 and/or C4851/C3610 on the reductant harness going to the reductant pump/heater assembly and the reductant level sensor/quality module. To correct the condition, follow the Service Procedure steps to replace the reductant tank harness, the reductant pump/heater assembly and/or the reductant tank.
21N03-S22021-09-30. Service bulletin. ELECTRICAL SYSTEM:ADAS:CONTROL MODULE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement; Owner letters are scheduled to mail during the week of September 27, 2021• Submitting Claims with Ford Protect for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA with Ford Protect.• Submitting Claims with Customer Loyalty Program for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA using CLP Funds. This program extends the warranty coverage of the engine cam phasers until January 1, 2023 provided the Repair Order (RO) date of Powertrain Control Module reflash under Customer Satisfaction Program 21B10 occurs on or before February 28, 2022
21N082021-09-30. Service bulletin. ELECTRICAL SYSTEM. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder ;In a very low percentage of the affected vehicles, an engine shudder may develop after receiving the PCM update provided in program 21B10. For peace of mind, Ford is providing a no-cost, one-time repair for customers who receive the PCM update under program 21B10 to revert the PCM calibration back to its original state before program 21B10.
21B10-S32021-09-30. Service bulletin. ELECTRICAL SYSTEM. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle
SSM 501542021-09-28. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. Some 2018-2020 Expedition/Navigator, 2015-2020 F150 and 2017-2020 F-Super Duty vehicles equipped with power running boards (PRB) may exhibit a condition where the PRBs are disabled, changing the feature menu setting from Auto to Off mode in the instrumental panel cluster (IPC), DTC U3003:16 stored in the running board control module (RBM) and with or without an illuminated charging system indicator lamp. This may be due to a low battery voltage event or a fully discharged battery. To correct this condition, inspect the charging system and correct the low battery voltage event. Refer to Workshop Manual (WSM), Section 501-08 > Diagnosis and Testing. Configure the PRB system mode from Off to Auto mode in the Advance Settings of the IPC. Refer to the Owner's Manual > Power Running Boards.
SSM 500672021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 500582021-09-04. Service bulletin. ELECTRICAL SYSTEM. 2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 or v122.06 stating "Unable To Communicate With The Module". This is due to an issue with the Transmission Characterization/Solenoid IDN tool in IDS v122.05 and v122.06. To resolve the issue, uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, install IDS v123.01 (123_FULL) and retry the Transmission Characterization/Solenoid IDN tool using IDS level v123.01.
SSM 500392021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS.
SSM 500302021-09-04. Service bulletin. ELECTRICAL SYSTEM. 2017-2020 F-150 vehicles equipped with a 3.5L engine and a 10R80 transmission may experience an error message while performing Transmission Characterization/Solenoid IDN with IDS v122.05 stating "Unable To Communicate With The Module". A temporary workaround to complete programming is as follows: Uninstall IDS from the computer. Then, run the IDS clean up utility tool, located on PTS > Rotunda Tab > Diagnostic Tool Support > IDS Support > IDS troubleshooting guide. Next, Install IDS v122.01 (122_FULL) and retry the Transmission Characterization/Solenoid IDN using IDS level 122.01. Monitor OASIS for updates.
TSB 21-22632021-09-02. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
TSB 21-21502021-06-03. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2019-2020 Edge/F-150/Fusion/Continental/MKZ/Nautilus, 2019-2021 Mustang/Ranger/Transit Connect, 2020-2021 EcoSport/Escape/Expedition/Explorer/F-Super Duty/Aviator/Corsair/Navigator and 2021 Bronco Sport vehicles with SYNC 3 may experience various SYNC performance related concerns. To correct the condition, follow the Service Procedure.
SSM 498202021-06-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Some 2017-2021 Ford and Lincoln vehicle owners may experience a condition of missing Authorization, Command and Control, Battery Charging Details or Phone-as-a-Key setup buttons/selections in their FordPass or LincolnWay App. This condition is due to an error within the FordPass or LincolnWay App and not due to a concern on the vehicle. Verify that the customers FordPass or LincolnWay App is at the latest version. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM)/remote function actuator (RFA) will not resolve this condition. If the condition persists, Utilize the FordPass Guides or Lincoln Way Concierge teams.
SSM 498032021-06-01. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EQUIPMENT ADAPTIVE/MOBILITY. Some 2018-2020 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 497952021-06-01. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS; ELECTRICAL SYSTEM. Some 2018-2021 Ford and Lincoln vehicles may not be able to perform remote commands via the FordPass/LincolnWay App due to an erroneous deep sleep message. If the vehicle has been driven within 14 days and the battery state of charge is above 9.5 volts when the deep sleep message set, this is an erroneous message. Starting and running the vehicle will clear the message and allow the remote commands to function again. Inform customers that engineering is currently working on a solution for this condition that will be released via an over the air (OTA) update that is expected in June 2021. Replacement or reprogramming of the telematics control unit (TCU)/gateway module (GWM) will not resolve this condition. Monitor OASIS for additional information and schedule service appointments for customers once the repair becomes available.
SSM 497082021-03-31. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2019 F-150/F-Super Duty/Expedition/Navigator and 2020 Explorer/Aviator vehicles may exhibit a 'Trailer Connected' or 'Trailer Disconnected' message in the vehicle's message center with no trailer attached to the vehicle. To address this condition, reprogram the trailer module (TRM) using the appropriate Ford diagnostic scan tool. For claiming use causal part 19H332 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual.
SSM 496182021-03-03. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2021 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with DTC P025A And/Or DTC U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs or loose/corroded grounds. Inspect FPCM connector, applicable grounds(F-150- G401, Expedition/Navigator- G403, Transit- G401, 2018-2019 Explorer G302, 2020-2021 Explorer/Aviator- G407) and confirm FPCM connector (F-150- C4336, Expedition/Navigator- C433, Transit- C433, 2018-2019 Explorer C3239, 2020-2021 Explorer/Aviator- C4033) is fully seated prior to performing PC/ED diagnostics or replacing any components.
TSB 20-24232021-01-05. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; POWER TRAIN. Some 2018-2020 F-150/Navigator vehicles equipped with a 3.5L EcoBoost High-Output engine and built on or before 11-Sept-2020 may exhibit excessive oil consumption with no visible oil leaks with or without diagnostic trouble code (DTC) P0365 and/or P0369. To correct the condition, follow the Service Procedure steps to reprogram the powertrain control module (PCM) and if necessary, replace the engine valve covers.
TSB 20-23852020-12-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Some 2020 F-150 Lariat vehicles equipped with the snow plow prep package may exhibit the snow plow button illuminating when you press the start/stop deactivation button, and the start/stop deactivation indicator illuminating when you press the snow plow button. Both features otherwise function correctly, and the correct messages illuminate in the message center when pressing either button. This may be due to incorrect switch circuitry. To correct the condition, follow the Service Procedure steps to swap circuit pin locations.
20B392020-12-05. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:ADAS:HUD:CAMERA/SENSOR. Certain 2020 Model Year Multiple Vehicle Lines Front View and Center High Mount Stop Lamp Camera Improper Function In some of the affected vehicles, insufficient electrical conductivity within the Printed Circuit Board (PCB) internal to the camera may lead to intermittent front view or Center High Mount Stop Lamp (CHMSL) camera operation. This could result in a blank or distorted image from the front of the vehicle or of the truck bed Dealers are to replace the front view camera or the CHMSL camera following the dealer bulletin technical information. This service must be performed on all affected vehicles at no charge to the vehicle owner.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.