Service bulletins for the 2018 Ford Expedition
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
165 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| SSM 50346 | 2021-12-26. Service bulletin. EQUIPMENT:ELECTRICAL. Some 2018-2021 Ford and Lincoln vehicles may exhibit inoperative remote features via the Ford Pass/Lincoln Way mobile app, incomplete user authorization, no modem electronic serial number (ESN) displayed or DTCs U2100 and/or B156D in the telematics control unit (TCU). These symptoms may persist even after performing a TCU software update and/or replacement. To correct this condition, start a new session with the latest version of the appropriate diagnostic scan tool and perform a PMI on the TCU. If issues persist, open a hotline assistance request and include the IDS version (if applicable) used to perform the PMI and the Authorization Status PID value in the TCU datalogger. For claiming use causal part 14G229 and applicable labor times in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
|---|---|
| 21N03-S3 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement REASON FOR THIS SUPPLEMENT • Parts Requirements / Ordering Information - Due to limited availability of originally specified parts, alternate option parts have been added. • Submitting Claims with Customer Loyalty Program for Balance Remaining – Added instructions on how to use Lincoln Loyalty funds. |
| SSM 50306 | 2021-12-07. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2021 EcoSport, Expedition, Navigator; 2019-2021 Ranger; 2020-2021 Escape, Corsair, Explorer, Transit; 2021 Bronco, Bronco Sport, Edge, Nautilus, F-150, Mustang; 2019-2022 Transit Connect; 2020-2022 Aviator, F-Super Duty; and 2022 Maverick vehicles may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0496, P0456, P0455, P04F0, and/or P0451. Ford has tested returned EVAP canister purge valves and found them to be fully functional. Prior to replacing the canister purge valve or other EVAP components, perform the following tests using the Ford Diagnosis and Repair System (FDRS) Scan Tool: Full System EVAP Leak Test - FDRS Location: TOOLBOX > PCM > PCM - Evap Emissions System Test and the EVAP Purge Valve Leak Test - FDRS Location: TOOLBOX > PCM > Evap Emission System Toolbox > CPV Check. |
| SSM 50251 | 2021-12-07. Service bulletin. UNKNOWN OR OTHER; COMMUNICATION:MANUFACTURER TELEMATICS. Some 2017-2020 Ford and Lincoln vehicles equipped with a TCU may exhibit inoperative remote features via Ford Pass/Lincoln Way mobile app, incomplete user authorization and/or no modem electronic serial number (ESN) displayed. To correct this condition prior to programming, remove the TCU fuse for 5 minutes then reinstall. Delete all previous session files for the vehicle. Verify that the electronic serial number (ESN) is now displayed. Start a new IDS/FDRS session. Program the TCU to the latest IDS/FDRS version level. Make sure you are connected to the internet before retesting. If the concern is still present, follow normal diagnostics in Workshop Manual(WSM), Section 415-00. Refer to PTS OASIS home page for TCU version identification. For claiming, use causal part 14G229 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| TSB 21-2419 | 2021-12-01. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; STRUCTURE. Some 2018-2021 Expedition/Navigator vehicles built on or before 02-Aug-2021 may exhibit a condition where the gap hiders of the load floor compartment come detached. This may be due to the joint between the gap hiders and the bin. To correct the condition, follow the Service Procedure steps to replace the damaged gap hiders. |
| 21N08 | 2021-11-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ENGINE. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder; Owner Letter sent |
| TSB 21-2315 | 2021-10-05. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang and 2019-2021 Ranger vehicles equipped with a 10R80 automatic transmission may exhibit a harsh engagement/harsh shift/delayed shift. It is possible the vehicle may also have an illuminated malfunction indicator lamp (MIL) or diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to incompatibility of the adaptive calibration to adapt to hardware wear-in over time. To correct the condition, follow the Service Procedure steps to overhaul the main control valve body and/or perform an adaptive learning drive cycle. |
| 21N03-S2 | 2021-09-30. Service bulletin. ELECTRICAL SYSTEM:ADAS:CONTROL MODULE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Cam Phaser Replacement; Owner letters are scheduled to mail during the week of September 27, 2021• Submitting Claims with Ford Protect for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA with Ford Protect.• Submitting Claims with Customer Loyalty Program for Balance Remaining: Added instruction on how to claim the customer paid portion of the FSA using CLP Funds. This program extends the warranty coverage of the engine cam phasers until January 1, 2023 provided the Repair Order (RO) date of Powertrain Control Module reflash under Customer Satisfaction Program 21B10 occurs on or before February 28, 2022 |
| 21N08 | 2021-09-30. Service bulletin. ELECTRICAL SYSTEM. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine PCM Reprogram Due to Engine Shudder ;In a very low percentage of the affected vehicles, an engine shudder may develop after receiving the PCM update provided in program 21B10. For peace of mind, Ford is providing a no-cost, one-time repair for customers who receive the PCM update under program 21B10 to revert the PCM calibration back to its original state before program 21B10. |
| 21B10-S3 | 2021-09-30. Service bulletin. ELECTRICAL SYSTEM. Certain 2017-2020 Model Year F-150, 2018-2020 Expedition, and 2018-2020 Navigator Vehicles Equipped with a 3.5L GTDI Engine Powertrain Control Module Reprogram for Cam Phaser Rattle |
| TSB 21-2292 | 2021-09-30. Service bulletin. VISIBILITY:SUN/MOON ROOF ASSEMBLY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; STRUCTURE:BODY:ROOF AND PILLARS. Some 2015-2021 F-150, 2017-2021 F-Super Duty and 2018-2021 Expedition/Navigator vehicles equipped with a vista roof opening panel may exhibit a binding/sticking, glass stuck open or closed, noisy operation including chatter, rattling, or grinding. This may be due to the glass panel brackets cracking and/or breaking apart. The glass panel brackets are serviceable separately from the frame assembly and require the roof opening panel glass to be moved to the vent position. To correct the condition, follow the Service Procedure to replace the roof opening panel glass brackets |
| TSB 21-2250 | 2021-09-30. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. Some 2015-2020 F-150, 2017-2020 Super Duty and 2018-2020 Expedition/Navigator vehicles may exhibit poor air conditioning (A/C) performance, loss of airflow and/or engine cooling fans running continuously from high A/C pressures. This concern may be from the evaporator freezing up due to the evaporator temperature sensor being biased. To correct the condition, follow the Service Procedure steps to replace the evaporator temperature sensor. |
| SSM 50154 | 2021-09-28. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. Some 2018-2020 Expedition/Navigator, 2015-2020 F150 and 2017-2020 F-Super Duty vehicles equipped with power running boards (PRB) may exhibit a condition where the PRBs are disabled, changing the feature menu setting from Auto to Off mode in the instrumental panel cluster (IPC), DTC U3003:16 stored in the running board control module (RBM) and with or without an illuminated charging system indicator lamp. This may be due to a low battery voltage event or a fully discharged battery. To correct this condition, inspect the charging system and correct the low battery voltage event. Refer to Workshop Manual (WSM), Section 501-08 > Diagnosis and Testing. Configure the PRB system mode from Off to Auto mode in the Advance Settings of the IPC. Refer to the Owner's Manual > Power Running Boards. |
| SSM 50089 | 2021-09-28. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, GASOLINE. Some 2017-2021 Ford and Lincoln vehicles equipped with 3.3L, 3.5L EcoBoost, or 5.0L engines may exhibit stalling, lack of power, low fuel rail pressure and/or DTCs P0087 or P008A after a repair was made that required the removal of the fuel line that connects the high-pressure fuel pump to the port injection rail, such as injector replacements or base engine repairs. This line must be installed in the correct orientation as it has an internal one-way check valve. To determine if the fuel line has been installed improperly, look at the position of the Oetiker clamp (stainless band clamped around the black fuel line). The clamp holds the one-way check valve in place and should be located closest to the end connected to the port injection rail. If the clamp is not closest to the port injection rail, remove and reinstall the line in the proper orientation. |
| 21N03 | 2021-09-05. Service bulletin. ENGINE AND ENGINE COOLING. In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 21, 2021 and continue to experience cam phaser noise after receiving that PCM update. |
| 21B10-S2 | 2021-09-05. Service bulletin. ENGINE AND ENGINE COOLING. It may be possible that an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after your vehicle was turned off for an extended period of time, or as a knocking noise when the engine is idling after it is warmed up. |
| SSM 50067 | 2021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTC) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK12 to cycle the affected VCT solenoid 10 times to attempt to clear the debris. For claiming, use causal part 6M280 and applicable labor operations in Section 10 of the Service Labor Time Standards (SLTS) Manual. |
| SSM 50064 | 2021-09-04. Service bulletin. SERVICE BRAKES, ELECTRIC:SOFTWARE/PROGRAMMING. Some 2013-2021 Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting, bluing/discoloration and/or heat spots. For additional information, refer to WSM section 206-00. |
| SSM 50049 | 2021-09-04. Service bulletin. POWER TRAIN:MANUAL TRANSMISSION:INTERNAL:DOGS/SYNCHROS. Some 2017-2021 Ford and Lincoln vehicle customers may receive a message in their FordPass or Lincoln Way App stating Feature Unavailable. Since this is a fleet vehicle, it cannot access the SYNC Connect or FordPass Connect feature or Lincoln Connect or Embedded Modem Do not replace the TCU or perform any repair to resolve this condition. Refer the owner of the vehicle to Ford Pass Guides or Lincoln Way Concierge Teams to assist in removing the fleet telematics subscription. |
| SSM 50045 | 2021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2018-2021 Ford/Lincoln vehicles equipped with a wireless charging pad may exhibit an inoperative charging pad, slow charging, a notification that the phone has been mispositioned on the charging pad and/or the phone charging icon in the center screen is not showing. This may be due to the customer's phone if they are using an iPhone 12. Vehicles equipped with a wireless charging pad are designed to charge best with phones that follow the Qi standard. The iPhone 12 hardware currently does not follow the Qi standard for wireless charging. This may make it difficult for Ford and Lincoln vehicles to wirelessly charge this specific phone. The phone can still be charged using the USB cable if the vehicle experiences the above symptoms. If the customer is using an iPhone 12, verify the wireless charging pad works with a Qi certified phone prior to any part replacements. |
| SSM 50039 | 2021-09-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2021 Ford or Lincoln vehicles equipped with SYNC 3 or SYNC 4 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale. To prevent a SYNC system lockup during transport mode deactivation, follow the Workshop Manual (WSM) procedure exactly allowing time for the SYNC system to complete its tasks such as fully booting up or powering down and shutting off before moving to the next step of the procedure. If the vehicle exhibits a blank screen or SYNC symptoms after transport mode deactivation, refer to WSM, Section 415-00 for normal diagnosis. The SYNC version can be confirmed via OASIS. |
| TSB 21-2280 | 2021-09-02. Service bulletin. ENGINE AND ENGINE COOLING. Some 2018-2021 F-150 vehicles equipped with a 3.5L PowerBoost, 3.5L EcoBoost or 2.7L EcoBoost engine and some 2018-2021 Expedition and Navigator vehicles equipped with a 3.5L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04F0 and/or P144C stored in the powertrain control module (PCM). This may be due to loose or partially connected evaporative emissions (EVAP) vapor lines. |
| TSB 21-2275 | 2021-09-02. Service bulletin. LATCHES/LOCKS/LINKAGES. Some 2018-2020 Expedition/Navigator vehicles built on or before 7-Jun-2020 may exhibit a difficulty unlatching or latching doors and/or locking or unlocking doors. This may be due to water intrusion into the door handle cables. To correct the condition, follow the Service Procedure steps to replace the mini latch module assembly. |
| TSB 21-2236 | 2021-08-02. Service bulletin. SEATS. Some 2013-2018 C-Max, 2013-2020 Fusion/MKZ, 2013-2021 Escape, 2015-2018 Focus, 2015-2019 MKC, 2015-2021 Edge/F150/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017-2021 F-Super Duty, 2018-2021 EcoSport/Expedition, 2019-2021 Ranger/Nautilus, 2021 Bronco Sport/Mustang Mach-E vehicles may experience seat pan looseness, lateral movement, or a clunk/thump noise on turns. This may be due to the seat pan track. To correct the condition, follow the Service Procedure steps to install a reinforcement. |
| 21N03-S1 | 2021-08-02. Service bulletin. ENGINE AND ENGINE COOLING. In some of the affected vehicles, an undesirable noise may develop from the cam phasers in the 3.5L GTDI engine. This noise might occur as a rattle when starting the engine after the vehicle was turned off for an extended period of time or as a knocking noise when the engine is idling after it is warmed up. These concerns should be addressed by the updated calibration provided in FSA 21B10. However, for peace of mind, Ford is providing an extended warranty for customers who receive the PCM update under program 21B10 prior to December 31, 2021 and continue to experience cam phaser noise after receiving that PCM update, A cam phaser that has developed an undesirable noise does not affect the vehicle safety, performance, or emissions. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.