WenmarOpen by Wenmar Pro

Service bulletins for the 2017 Ford Edge

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

180 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
TSB 19-20172019-04-01. Service bulletin. POWER TRAIN; EQUIPMENT. Some all-wheel drive (AWD) 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost/Fusion vehicles equipped with 2.0L/2.7L EcoBoost/MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost/Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost/Explorer vehicles equipped with 2.3L EcoBoost/Focus RS equipped with 2.3L EcoBoost, and 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure steps to correct the condition.
SSM 477492019-03-04. Service bulletin. EQUIPMENT. Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
SSM 477112019-03-04. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2019 Ford and Lincoln vehicles equipped with SYNC 3 and a 6, 8 or 10 inch screen may show a pop-up message every key cycle that states 'SYNC can check for updates when connected to a WiFi network'. To remove the inconvenience of the pop-up the customer can either connect to a trusted WiFi network to complete the setup process or turn off WiFi in the WiFi settings located under the Settings menu. Adjusting the setting for the customer is not a warrantable defect.
TSB 18-23782019-03-04. Service bulletin. FUEL SYSTEM, GASOLINE. Some 2015-2019 Edge, 2016-2018 MKX, and 2019 Nautilus vehicles equipped with all wheel drive (AWD) may exhibit a fuel slosh noise primarily when the fuel tank is over 3/4 full and when driving at low speeds. This may be due to the fuel moving around in the fuel tank. Follow the Service Procedure steps to correct the condition.
TSB 18-23612019-03-04. Service bulletin. EQUIPMENT; SEATS. Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
SSM 476622019-01-07. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the turbocharger or the turbocharger oil supply tube are replaced. Turbocharger bearing failure may occur if oil starvation occurs due to a restricted filter.
SSM 476382019-01-07. Service bulletin. STEERING; STEERING: STEERING WHEEL/HANDLE BAR. 2013-2019 vehicles equipped with a LKS system with customer complaints of steering wheel vibration, steering pull or vehicle drift may be due to an alert and/or steering aid input from the LKS. The LKS system detects unintentional drifting toward the outside of the lane and alerts and/or aids vehicle to stay in the lane. Be sure the customer understands how the lane departure warning feature settings work for Alert (steering wheel vibration) and Aid (steering input toward lane center). Further information on the LKS can be found in the owners manual. If the customers concern is due to the LKS functioning as intended, do not attempt to repair.
SSM 476352019-01-07. Service bulletin. ELECTRICAL SYSTEM. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
TSB 18-23392019-01-07. Service bulletin. STRUCTURE:BODY:DOOR. Some 2015-2018 Edge vehicles may exhibit dirt, dust and/or ice accumulation at the bottom of the inside of the front and/or rear door openings. This may be due to extended driving on non-paved or slushy roads. Follow the Service Procedure steps to correct the condition.
SSM 475382018-12-03. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 may exhibit the Android Auto Preference menu selection is not present after an update to version 3.0 software. In prior versions of SYNC 3 software this menu was present, however in version 3.0 software the Android Auto Preference menu will only show up once an Android Phone has been initially connected to SYNC. This an operating characteristic of the Android Auto application after the SYNC 3.0 update and no repairs should be attempted.
SSM 475762018-11-19. Service bulletin. EQUIPMENT; ENGINE; POWER TRAIN. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost engine may exhibit a rattle noise at idle. This may be due to a flexplate crack around the crankshaft. To resolve this concern, verify that the flexplate is cracked around the crankshaft using the inspection plate and a mirror. If the flexplate is cracked, replace the transmission fluid pump, flexplate, flexplate bolts and torque converter. Refer to Workshop Manual (WSM), Section 303-01A and 307-01. When replacing the torque converter, ensure that the torque converter pilot hub is lubricated with Multi-Purpose Grease XL-5-A (ESB-M1C930-B) prior to reassembly. For claiming, use causal part 6375 and applicable labor operations in Section 06 of the Service Labor Time Standards (SLTS) Manual.
SSM 474892018-09-24. Service bulletin. STEERING. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic trouble codes (DTCs), no start, no crank conditions or the IPC inoperative. If a vehicle displays these issues, disconnect the equipment from the DLC and disconnect the vehicle battery. Wait 10 minutes and reinstall with the ignition off. Clear any DTCs present and retest.
SSM 474622018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. 2015-2018 Edge, Fusion, Focus, MKZ, MKC, Escape vehicles equipped with a 2.0L EcoBoost engine may exhibit coolant consumption, white smoke and/or a runs rough condition. Refer to the extended coolant pressure test and checking for combustion gases in Workshop Manual (WSM), Section 303-03A. If internal coolant loss is confirmed, further investigation of the head gasket interface is required. Carefully inspect the cylinder block and head for erosion, pitting, and flatness defects, primarily between the cylinder to cylinder bore bridges. If defects to the aluminum surface on the cylinder block and/or cylinder head are found, follow the cost cap tool for component replacement. Follow WSM, Section 303-01A for the repair procedures
SSM 474462018-09-24. Service bulletin. ENGINE AND ENGINE COOLING. Some Ford and Lincoln vehicles equipped with a 2.7L or 3.0L EcoBoost engine may exhibit an oil leak from the engine oil pan RTV seal. Replace the oil pan following the procedure in Workshop Manual (WSM) Section, 303-01. After removing the oil pan it is suggested to allow the crankcase to drain overnight to minimize the chance of residual oil contaminating the crankcase sealing rail. Remove all traces of old RTV and clean the engine sealing surface using only Motorcraftù Metal Brake Parts Cleaner, then wipe with Motorcraftù Metal Surface Prep Wipes and allow to air dry. Refer to WSM, Section 303-00 > RTV Sealing Surface Cleaning and Preparation. If possible, allow the new RTV sealant to cure for 4 hours before refilling the engine with oil. Skipping or improperly completing steps may result in repeat oil pan leaks.
SSM 474442018-09-24. Service bulletin. ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 not at the latest software level may exhibit Various Performance Related concerns such as Display Operation, Navigation, Voice Recognition, Phone Pairing, Applink, Travel Link, Slow System Response, etc. Check for SYNC software update under the OASIS Tab SYNC selection. If an update is available refer to WSM, Section 415-00 and update the APIM software. After Installation, complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
TSB 18-22552018-09-24. Service bulletin. ENGINE. Some 2013-2018 Escape vehicles equipped with 1.5L/1.6L/2.0L EcoBoost, 2013-2018 Fusion vehicles equipped with 2.0L/2.7L EcoBoost, 2013-2018 MKZ vehicles equipped with 2.0L EcoBoost, 2017-18 MKZ vehicles equipped with 3.0L EcoBoost, 2015-2018 MKC vehicles equipped with 2.0L/2.3L EcoBoost, 2015-2018 Edge vehicles equipped with 2.0L/2.7L EcoBoost, 2016-2018 MKX vehicles equipped with 2.0L and 2.7L EcoBoost, 2016-2018 Explorer vehicles equipped with 2.3L EcoBoost, 2017-2018 Continental vehicles equipped with 2.7L/3.0L EcoBoost and 2016-2018 Focus RS equipped with 2.3L EcoBoost may exhibit a dark black fluid leak from the right side transfer case intermediate shaft seal. Follow the Service Procedure to correct the condition.
SSM 473982018-09-10. Service bulletin. POWER TRAIN; ENGINE; EQUIPMENT. Some 2015-2018 Edge vehicles equipped with a 2.0L EcoBoost and 6F35 transmission may exhibit a rattle noise from the transmission bellhousing area while running. This may be the result of a cracked engine flexplate. When replacing the flexplate, lubricate the torque converter pilot hub with Multi-Purpose Grease XL-5-A (ESB-M1C93-B) before reassembling. Make sure the transmission locator dowel pins are correctly installed. If the dowel pins were pulled out of the engine block, new dowel pins will need to be installed in the engine block. Failure to do so could result in a repeat repair. Refer to Workshop Manual (WSM), Section 307-01A. Engineering is investigating, monitor OASIS for updates. To assist with the investigation use the Report a Vehicle Concern link at the bottom of the OASIS report and fill out the form.
tsb18-22122018-09-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Some 2016-2018 Edge vehicles equipped with a 2.0L EcoBoost engine built on or before 12-Mar-2018 may exhibit an illuminated MIL with DTC P0036 stored in the powertrain control module (PCM). Follow the Service Procedure steps to correct the condition.
18L022018-07-23. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
18M022018-07-23. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. Certain 2017 Model Year Multiple Vehicle Lines - California Emission Warranty Parts Coverage
SSM 473802018-07-23. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM. Some 2016-2018 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key off for 5 minutes which is critical for a successful installation. If no updates are available or a blue or black screen is present after an update refer to WSM, Section 415-00 for diagnosis or SYNC 3 intermittent blank screen GSB for tips. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
SSM 473792018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Various 2016-2018 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 473392018-07-23. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Some 2017-2018 Edge vehicles with 3.5L engines and MKX vehicles with 3.7L engines may exhibit an illuminated MIL with DTC P013C in the powertrain control module (PCM). This may be due to an exhaust system leak. Exhaust leak inspection should be conducted before performing Powertrain Control/Emissions Diagnostics PC/ED Manual diagnostic routines. Inspect for carbon soot/moisture witness marks at all exhaust connections and catalyst monitor sensor (CMS) threads. Refer to Workshop Manual (WSM), Section 303-14C. Inspect CMS crush washer to confirm sensor is fully seated in the exhaust pipe. Apply soapy water to exhaust connections including CMS threads, while exhaust flow is restricted at the tailpipe and exhaust system is pressurized at 5 PSI (do not exceed 5 PSI), will increase ability to identify and confirm leaks.
SSM 470412018-06-11. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then turn the key back on before testing the touch screen. If the software is at a later version than 2.2, proceed with normal diagnostics in Workshop Manual (WSM), Section 415-00. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the Service Labor Times Standards (SLTS) manual.
SSM 470092018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT. The Accessory (Wireless) Keyless Entry Keypad can only be used with vehicles that are factory built with Remote Keyless Entry (RKE). The master code for the Accessory (Wireless) Keyless Entry Keypad can be retrieved from FMCDealer - Parts and Service - Parts Product Line Information - Keys/Entry Devices - Aftermarket Keyless Entry Keypad Code Access. Access to this site is granted through Dealer Program Enrollment System (DPES) and Dealer Principal, General Manager or Parts and Service Director can authorize users. Once authorized the retrieval process for master code can be obtained. The master code for the Accessory Keyless Entry Keypad cannot be retrieved from the body control module(BCM) with a diagnostic tool.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.